Hi Andy:
在 2022/12/6 23:23, Andy Shevchenko 写道:
On Tue, Dec 06, 2022 at 11:16:56AM +0800, Binbin Zhou wrote:
This I2C module is integrated into the Loongson-2K SoCs and Loongson
LS7A bridge chip.
Much better, thanks!
...
+/*
+ * The I2C controller has a fixed I2C bus frequency by default, but to
+ * be compatible with more client devices, we can obtain the set I2C
+ * bus frequency from ACPI or FDT.
+ */
+static void ls2x_i2c_adjust_bus_speed(struct ls2x_i2c_priv *priv)
+{
+ u16 val = 0x12c; /* Default value of I2C divider latch register */
Besides comment better to be placed on top of the commented line, the value
is better to have its own definition where you place the comment and elaborate
what it means in practice (The clock frequency is changed? Bus speed is
different?)
Ok, I'll put this comment on a separate line.
The LS2X I2C supports STANDARD_MODE and FAST_MODE, so the maximum bus
frequency is 400kHz.
"0x12c" is our empirical value after experimentation and represents 33KHz.
Also, I think the better way is:
@@ -53,6 +53,15 @@
#define LS2X_CTR_IEN BIT(6) /* Enable i2c interrupt */
#define LS2X_CTR_MST BIT(5) /* 0: Slave mode 1: Master mode */
+/* The PCLK clock frequency input from the LPB bus */
+#define LS2X_I2C_PCLK_FREQ (50 * HZ_PER_MHZ)
+/*
+ * The LS2X I2C controller supports standard mode and fast mode,
+ * so the maximum bus frequency is 400kHz.
+ * The '33KHz' is our empirical value after experimentation.
+ */
+#define LS2X_I2C_FREQ_STD (33 * HZ_PER_KHZ)
+
struct ls2x_i2c_priv {
struct i2c_adapter adapter;
struct device *dev;
@@ -231,17 +240,19 @@ static irqreturn_t ls2x_i2c_irq_handler(int
this_irq, void *dev_id)
*/
static void ls2x_i2c_adjust_bus_speed(struct ls2x_i2c_priv *priv)
{
- u16 val = 0x12c; /* Default value of I2C divider latch register */
struct i2c_timings *t = &priv->i2c_t;
u32 acpi_speed = i2c_acpi_find_bus_speed(priv->dev);
i2c_parse_fw_timings(priv->dev, t, false);
if (acpi_speed || t->bus_freq_hz)
- val = 10 * HZ_PER_MHZ / max(t->bus_freq_hz, acpi_speed) - 1;
+ t->bus_freq_hz = max(t->bus_freq_hz, acpi_speed);
+ else
+ t->bus_freq_hz = LS2X_I2C_FREQ_STD;
- /* Set LS2X I2C frequency */
- writel(val, priv->base + I2C_LS2X_PRER_LO);
+ /* Calculate and set LS2X I2C frequency */
+ writel((LS2X_I2C_PCLK_FREQ / (5 * t->bus_freq_hz) - 1),
+ priv->base + I2C_LS2X_PRER_LO);
}
+ struct i2c_timings *t = &priv->i2c_t;
+ u32 acpi_speed = i2c_acpi_find_bus_speed(priv->dev);
+
+ i2c_parse_fw_timings(priv->dev, t, false);
+
+ if (acpi_speed || t->bus_freq_hz)
+ val = 10 * HZ_PER_MHZ / max(t->bus_freq_hz, acpi_speed) - 1;
+
+ /* Set LS2X I2C frequency */
+ writel(val, priv->base + I2C_LS2X_PRER_LO);
+}
...
+ writeb(data | LS2X_CTR_EN | LS2X_CTR_IEN | LS2X_CTR_MST,
+ priv->base + I2C_LS2X_CTR);
Wrong indentation.
...
+ r = devm_request_irq(dev, irq, ls2x_i2c_irq_handler,
+ IRQF_SHARED, "ls2x-i2c", priv);
+ if (r < 0)
+ return dev_err_probe(dev, r, "Unable to request irq %d\n", irq);
You requested IRQ without filling all data structures. Is it fine? Have you
checked that with CONFIG_DEBUG_SHIRQ being enabled?
Sorry, I don't quite understand what you mean by "without filling all
data structures", I need call ls2x_i2c_reginit(priv) before it ?
I see that other i2c drivers request interrupts at about the same time
as I do.
I tested it with CONFIG_DEBUG_SHIRQ and no exceptions were reported.
...
+ r = devm_i2c_add_adapter(dev, adap);
+ if (r)
+ return dev_err_probe(dev, r, "Failure adding adapter\n");
+
+ return 0;
+}
Looking at the above...
+static int ls2x_i2c_remove(struct platform_device *pdev)
+{
+ struct ls2x_i2c_priv *priv = platform_get_drvdata(pdev);
+
+ i2c_del_adapter(&priv->adapter);
...are you sure this is correct?
When we use devm_i2c_add_adapter(), the adapter will be auto deleted on
driver detach.
So I just drop the ls2x_i2c_remove() ?
+ return 0;
+}
...
+static int ls2x_i2c_suspend(struct device *dev)
+{
+ struct ls2x_i2c_priv *priv = dev_get_drvdata(dev);
+ priv->suspended = 1;
No protection needed?
Actually this variable is not used elsewhere, maybe it is useless, I
will try to remove it and add some necessary actions in the
suspend/rusume callbacks, such as disable i2c interrupts, to ensure
integrity.
+ return 0;
+}
+
+static int ls2x_i2c_resume(struct device *dev)
+{
+ struct ls2x_i2c_priv *priv = dev_get_drvdata(dev);
+ priv->suspended = 0;
Ditto.
+ ls2x_i2c_reginit(priv);
+ return 0;
+}
...
+MODULE_ALIAS("platform:ls2x-i2c");
Why is this required?
I just referred to other drivers before, and now the MODULE_DEVICE_TABLE
already creates proper alias for platform driver.
I will drop it.
Thanks.
Binbin
