Dne torek, 01. november 2022 ob 15:16:53 CET je Andre Przywara napisal(a):
> The Allwinner F1C100s series of SoCs contain three I2C controllers
> compatible to the ones used in other Allwinner SoCs.
>
> Add the DT nodes describing the resources of the controllers.
> I2C1 has only one possible pinmux, so add the pinctrl properties for
> that already.
> At least one board connects an on-board I2C chip to PD0/PD12 (I2C0), so
> include those pins already, to simplify referencing them later.
>
> Signed-off-by: Andre Przywara <andre.przywara@xxxxxxx>
> ---
> arch/arm/boot/dts/suniv-f1c100s.dtsi | 50 ++++++++++++++++++++++++++++
> 1 file changed, 50 insertions(+)
>
> diff --git a/arch/arm/boot/dts/suniv-f1c100s.dtsi
> b/arch/arm/boot/dts/suniv-f1c100s.dtsi index d5a6324e76465..2901c586971b4
> 100644
> --- a/arch/arm/boot/dts/suniv-f1c100s.dtsi
> +++ b/arch/arm/boot/dts/suniv-f1c100s.dtsi
> @@ -166,6 +166,18 @@ mmc0_pins: mmc0-pins {
> drive-strength = <30>;
> };
>
> + /omit-if-no-ref/
> + i2c0_pd_pins: i2c0-pd-pins {
> + pins = "PD0", "PD12";
> + function = "i2c0";
> + };
> +
> + /omit-if-no-ref/
Above flag is meaningless if i2c1_pins is always referenced by i2c1. Anyway, I
see in pinctrl driver that there are actually two possible pin assignments for
i2c1. One on port D and another on port B.
Best regards,
Jernej
> + i2c1_pins: i2c1-pins {
> + pins = "PD5", "PD6";
> + function = "i2c1";
> + };
> +
> spi0_pc_pins: spi0-pc-pins {
> pins = "PC0", "PC1", "PC2",
"PC3";
> function = "spi0";
> @@ -177,6 +189,44 @@ uart0_pe_pins: uart0-pe-pins {
> };
> };
>
> + i2c0: i2c@1c27000 {
> + compatible = "allwinner,suniv-f1c100s-i2c",
> + "allwinner,sun6i-a31-i2c";
> + reg = <0x01c27000 0x400>;
> + interrupts = <7>;
> + clocks = <&ccu CLK_BUS_I2C0>;
> + resets = <&ccu RST_BUS_I2C0>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c1: i2c@1c27400 {
> + compatible = "allwinner,suniv-f1c100s-i2c",
> + "allwinner,sun6i-a31-i2c";
> + reg = <0x01c27400 0x400>;
> + interrupts = <8>;
> + clocks = <&ccu CLK_BUS_I2C1>;
> + resets = <&ccu RST_BUS_I2C1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1_pins>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c2: i2c@1c27800 {
> + compatible = "allwinner,suniv-f1c100s-i2c",
> + "allwinner,sun6i-a31-i2c";
> + reg = <0x01c27800 0x400>;
> + interrupts = <9>;
> + clocks = <&ccu CLK_BUS_I2C2>;
> + resets = <&ccu RST_BUS_I2C2>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> timer@1c20c00 {
> compatible = "allwinner,suniv-f1c100s-
timer";
> reg = <0x01c20c00 0x90>;
