Add support for the following Maxim chips using the existing PCA954x
driver:
- MAX7356
- MAX7357
- MAX7358
- MAX7367
- MAX7368
- MAX7369
All added Maxim chips behave like the PCA954x, where a single SMBUS byte
write selects up to 8 channels to be bridged to the primary bus.
The MAX7357 exposes 6 additional registers at Power-On-Reset and is
configured to:
- Disabled interrupts on bus locked up detection
- Enable bus locked-up clearing
- Disconnect only locked bus instead of all channels
While the MAX7357/MAX7358 have interrupt support, they don't act as
interrupt controller like the PCA9545 does. Thus don't enable IRQ support
and handle them like the PCA9548.
Tested using the MAX7357 and verified that the stalled bus is disconnected
while the other channels remain operational.
Signed-off-by: Patrick Rudolph <patrick.rudolph@xxxxxxxxxxxxx>
---
drivers/i2c/muxes/Kconfig | 4 +-
drivers/i2c/muxes/i2c-mux-pca954x.c | 92 +++++++++++++++++++++++++++--
2 files changed, 90 insertions(+), 6 deletions(-)
diff --git a/drivers/i2c/muxes/Kconfig b/drivers/i2c/muxes/Kconfig
index 1708b1a82da2..2ac99d044199 100644
--- a/drivers/i2c/muxes/Kconfig
+++ b/drivers/i2c/muxes/Kconfig
@@ -65,11 +65,11 @@ config I2C_MUX_PCA9541
will be called i2c-mux-pca9541.
config I2C_MUX_PCA954x
- tristate "NXP PCA954x and PCA984x I2C Mux/switches"
+ tristate "NXP PCA954x/PCA984x and Maxim MAX735x/MAX736x I2C Mux/switches"
depends on GPIOLIB || COMPILE_TEST
help
If you say yes here you get support for the NXP PCA954x
- and PCA984x I2C mux/switch devices.
+ and PCA984x and Maxim MAX735x/MAX736x I2C mux/switch devices.
This driver can also be built as a module. If so, the module
will be called i2c-mux-pca954x.
diff --git a/drivers/i2c/muxes/i2c-mux-pca954x.c b/drivers/i2c/muxes/i2c-mux-pca954x.c
index 4ad665757dd8..33b9a6a1fffa 100644
--- a/drivers/i2c/muxes/i2c-mux-pca954x.c
+++ b/drivers/i2c/muxes/i2c-mux-pca954x.c
@@ -4,6 +4,7 @@
*
* Copyright (c) 2008-2009 Rodolfo Giometti <giometti@xxxxxxxx>
* Copyright (c) 2008-2009 Eurotech S.p.A. <info@xxxxxxxxxxx>
+ * Copyright (c) 2022 Patrick Rudolph <patrick.rudolph@xxxxxxxxxxxxx>
*
* This module supports the PCA954x and PCA984x series of I2C multiplexer/switch
* chips made by NXP Semiconductors.
@@ -11,6 +12,12 @@
* PCA9540, PCA9542, PCA9543, PCA9544, PCA9545, PCA9546, PCA9547,
* PCA9548, PCA9846, PCA9847, PCA9848 and PCA9849.
*
+ * It's also compatible to Maxims MAX735x I2C switch chips, which are controlled
+ * as the NXP PCA9548 and the MAX736x chips that act like the PCA9544.
+ *
+ * This includes the:
+ * MAX7356, MAX7357, MAX7358, MAX7367, MAX7368 and MAX7369
+ *
* These chips are all controlled via the I2C bus itself, and all have a
* single 8-bit register. The upstream "parent" bus fans out to two,
* four, or eight downstream busses or channels; which of these
@@ -50,7 +57,30 @@
#define PCA954X_IRQ_OFFSET 4
+/*
+ * MAX7357 exposes 7 registers on POR which allow to configure additional
+ * features. Disable interrupts, enable bus locked-up clearing,
+ * isolate only the locked channel instead of all channels.
+ */
+#define MAX7357_CONF_INT_ENABLE BIT(0)
+#define MAX7357_CONF_FLUSH_OUT BIT(1)
+#define MAX7357_CONF_RELEASE_INT BIT(2)
+#define MAX7357_CONF_LOCK_UP_CLEAR BIT(3)
+#define MAX7357_CONF_DISCON_SINGLE_CHAN BIT(4)
+#define MAX7357_CONF_BUS_LOCKUP_DETECTION BIT(5)
+#define MAX7357_CONF_ENABLE_BASIC_MODE BIT(6)
+#define MAX7357_CONF_PRECONNECT_TEST BIT(7)
+
+#define MAX7357_CONF_DEFAULTS (MAX7357_CONF_FLUSH_OUT | \
+ MAX7357_CONF_DISCON_SINGLE_CHAN)
+
enum pca_type {
+ max_7367,
+ max_7368,
+ max_7369,
+ max_7356,
+ max_7357,
+ max_7358,
pca_9540,
pca_9542,
pca_9543,
@@ -69,6 +99,7 @@ struct chip_desc {
u8 nchans;
u8 enable; /* used for muxes only */
u8 has_irq;
+ u8 max7357;
enum muxtype {
pca954x_ismux = 0,
pca954x_isswi
@@ -90,8 +121,42 @@ struct pca954x {
raw_spinlock_t lock;
};
-/* Provide specs for the PCA954x types we know about */
+/* Provide specs for the PCA954x and MAX735x types we know about */
static const struct chip_desc chips[] = {
+ [max_7356] = {
+ .nchans = 8,
+ .muxtype = pca954x_isswi,
+ .id = { .manufacturer_id = I2C_DEVICE_ID_NONE },
+ },
+ [max_7357] = {
+ .nchans = 8,
+ .muxtype = pca954x_isswi,
+ .max7357 = 1,
+ .id = { .manufacturer_id = I2C_DEVICE_ID_NONE },
+ },
+ [max_7358] = {
+ .nchans = 8,
+ .muxtype = pca954x_isswi,
+ .id = { .manufacturer_id = I2C_DEVICE_ID_NONE },
+ },
+ [max_7367] = {
+ .nchans = 4,
+ .muxtype = pca954x_isswi,
+ .has_irq = 1,
+ .id = { .manufacturer_id = I2C_DEVICE_ID_NONE },
+ },
+ [max_7368] = {
+ .nchans = 4,
+ .muxtype = pca954x_isswi,
+ .id = { .manufacturer_id = I2C_DEVICE_ID_NONE },
+ },
+ [max_7369] = {
+ .nchans = 4,
+ .enable = 0x4,
+ .muxtype = pca954x_ismux,
+ .has_irq = 1,
+ .id = { .manufacturer_id = I2C_DEVICE_ID_NONE },
+ },
[pca_9540] = {
.nchans = 2,
.enable = 0x4,
@@ -177,6 +242,12 @@ static const struct chip_desc chips[] = {
};
static const struct i2c_device_id pca954x_id[] = {
+ { "max7356", max_7356 },
+ { "max7357", max_7357 },
+ { "max7358", max_7358 },
+ { "max7367", max_7367 },
+ { "max7368", max_7368 },
+ { "max7369", max_7369 },
{ "pca9540", pca_9540 },
{ "pca9542", pca_9542 },
{ "pca9543", pca_9543 },
@@ -194,6 +265,12 @@ static const struct i2c_device_id pca954x_id[] = {
MODULE_DEVICE_TABLE(i2c, pca954x_id);
static const struct of_device_id pca954x_of_match[] = {
+ { .compatible = "maxim,max7356", .data = &chips[max_7356] },
+ { .compatible = "maxim,max7357", .data = &chips[max_7357] },
+ { .compatible = "maxim,max7358", .data = &chips[max_7358] },
+ { .compatible = "maxim,max7367", .data = &chips[max_7367] },
+ { .compatible = "maxim,max7368", .data = &chips[max_7368] },
+ { .compatible = "maxim,max7369", .data = &chips[max_7369] },
{ .compatible = "nxp,pca9540", .data = &chips[pca_9540] },
{ .compatible = "nxp,pca9542", .data = &chips[pca_9542] },
{ .compatible = "nxp,pca9543", .data = &chips[pca_9543] },
@@ -401,9 +478,16 @@ static int pca954x_init(struct i2c_client *client, struct pca954x *data)
else
data->last_chan = 0; /* Disconnect multiplexer */
- ret = i2c_smbus_write_byte(client, data->last_chan);
- if (ret < 0)
- data->last_chan = 0;
+ if (data->chip->max7357) {
+ ret = i2c_smbus_write_byte_data(client, data->last_chan,
+ MAX7357_CONF_DEFAULTS);
+ if (ret < 0)
+ data->last_chan = 0;
+ } else {
+ ret = i2c_smbus_write_byte(client, data->last_chan);
+ if (ret < 0)
+ data->last_chan = 0;
+ }
return ret;
}
--
2.34.1
