On 1/29/22 01:39, Jonathan Neuschäfer wrote:
> The comments in this driver have a few typos. Let's fix them.
>
> Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@xxxxxxx>
Reviewed-by: Randy Dunlap <rdunlap@xxxxxxxxxxxxx>
Thanks.
> ---
> drivers/i2c/busses/i2c-npcm7xx.c | 16 ++++++++--------
> 1 file changed, 8 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-npcm7xx.c b/drivers/i2c/busses/i2c-npcm7xx.c
> index 2ad166355ec9b..71aad029425d8 100644
> --- a/drivers/i2c/busses/i2c-npcm7xx.c
> +++ b/drivers/i2c/busses/i2c-npcm7xx.c
> @@ -781,7 +781,7 @@ static void npcm_i2c_set_fifo(struct npcm_i2c *bus, int nread, int nwrite)
> /*
> * if we are about to read the first byte in blk rd mode,
> * don't NACK it. If slave returns zero size HW can't NACK
> - * it immidiattly, it will read extra byte and then NACK.
> + * it immediately, it will read extra byte and then NACK.
> */
> if (bus->rd_ind == 0 && bus->read_block_use) {
> /* set fifo to read one byte, no last: */
> @@ -981,7 +981,7 @@ static void npcm_i2c_slave_xmit(struct npcm_i2c *bus, u16 nwrite,
> /*
> * npcm_i2c_slave_wr_buf_sync:
> * currently slave IF only supports single byte operations.
> - * in order to utilyze the npcm HW FIFO, the driver will ask for 16 bytes
> + * in order to utilize the npcm HW FIFO, the driver will ask for 16 bytes
> * at a time, pack them in buffer, and then transmit them all together
> * to the FIFO and onward to the bus.
> * NACK on read will be once reached to bus->adap->quirks->max_read_len.
> @@ -1175,7 +1175,7 @@ static irqreturn_t npcm_i2c_int_slave_handler(struct npcm_i2c *bus)
> /*
> * the i2c module can response to 10 own SA.
> * check which one was addressed by the master.
> - * repond to the first one.
> + * respond to the first one.
> */
> addr = ((i2ccst3 & 0x07) << 7) |
> (i2ccst2 & 0x7F);
> @@ -1753,8 +1753,8 @@ static void npcm_i2c_recovery_init(struct i2c_adapter *_adap)
> /*
> * npcm i2c HW allows direct reading of SCL and SDA.
> * However, it does not support setting SCL and SDA directly.
> - * The recovery function can togle SCL when SDA is low (but not set)
> - * Getter functions used internally, and can be used externaly.
> + * The recovery function can toggle SCL when SDA is low (but not set)
> + * Getter functions used internally, and can be used externally.
> */
> rinfo->get_scl = npcm_i2c_get_SCL;
> rinfo->get_sda = npcm_i2c_get_SDA;
> @@ -1768,10 +1768,10 @@ static void npcm_i2c_recovery_init(struct i2c_adapter *_adap)
>
> /*
> * npcm_i2c_init_clk: init HW timing parameters.
> - * NPCM7XX i2c module timing parameters are depenent on module core clk (APB)
> + * NPCM7XX i2c module timing parameters are dependent on module core clk (APB)
> * and bus frequency.
> - * 100kHz bus requires tSCL = 4 * SCLFRQ * tCLK. LT and HT are simetric.
> - * 400kHz bus requires assymetric HT and LT. A different equation is recomended
> + * 100kHz bus requires tSCL = 4 * SCLFRQ * tCLK. LT and HT are symmetric.
> + * 400kHz bus requires asymmetric HT and LT. A different equation is recommended
> * by the HW designer, given core clock range (equations in comments below).
> *
> */
> --
> 2.34.1
>
--
~Randy
