[PATCH v2 4/6] i2c: designware: add MSCC Ocelot support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



The Microsemi Ocelot I2C controller is a designware IP. It also has a
second set of registers to allow tweaking SDA hold time and spike
filtering.

Cc: Rob Herring <robh+dt@xxxxxxxxxx>
Signed-off-by: Alexandre Belloni <alexandre.belloni@xxxxxxxxxxx>
---
Changes in v2:
 - improved binding doc
 - changed the model handling as suggested by Andy

 .../bindings/i2c/i2c-designware.txt           |  9 ++++-
 drivers/i2c/busses/i2c-designware-core.h      |  3 ++
 drivers/i2c/busses/i2c-designware-platdrv.c   | 40 +++++++++++++++++++
 3 files changed, 50 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/i2c/i2c-designware.txt b/Documentation/devicetree/bindings/i2c/i2c-designware.txt
index fbb0a6d8b964..0fb17387c735 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-designware.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-designware.txt
@@ -2,7 +2,8 @@
 
 Required properties :
 
- - compatible : should be "snps,designware-i2c"
+ - compatible : should be "snps,designware-i2c" or "mscc,ocelot-i2c" followed by
+   "snps,designware-i2c" for fallback
  - reg : Offset and length of the register set for the device
  - interrupts : <IRQ> where IRQ is the interrupt number.
 
@@ -11,8 +12,12 @@ Recommended properties :
  - clock-frequency : desired I2C bus clock frequency in Hz.
 
 Optional properties :
+ - reg : for "mscc,ocelot-i2c", a second register set to configure the SDA hold
+   time, named ICPU_CFG:TWI_DELAY in the datasheet.
+
  - i2c-sda-hold-time-ns : should contain the SDA hold time in nanoseconds.
-   This option is only supported in hardware blocks version 1.11a or newer.
+   This option is only supported in hardware blocks version 1.11a or newer and
+   on Microsemi SoCs ("mscc,ocelot-i2c" compatible).wtf
 
  - i2c-scl-falling-time-ns : should contain the SCL falling time in nanoseconds.
    This value which is by default 300ns is used to compute the tLOW period.
diff --git a/drivers/i2c/busses/i2c-designware-core.h b/drivers/i2c/busses/i2c-designware-core.h
index 870444bbbcc4..5e240ce9968e 100644
--- a/drivers/i2c/busses/i2c-designware-core.h
+++ b/drivers/i2c/busses/i2c-designware-core.h
@@ -225,6 +225,7 @@
 struct dw_i2c_dev {
 	struct device		*dev;
 	void __iomem		*base;
+	void __iomem		*ext;
 	struct completion	cmd_complete;
 	struct clk		*clk;
 	struct reset_control	*rst;
@@ -279,6 +280,8 @@ struct dw_i2c_dev {
 #define ACCESS_INTR_MASK	0x00000004
 
 #define MODEL_CHERRYTRAIL	0x00000100
+#define MODEL_MSCC_OCELOT	0x00000200
+#define MODEL_MASK		0x00000f00
 
 u32 dw_readl(struct dw_i2c_dev *dev, int offset);
 void dw_writel(struct dw_i2c_dev *dev, u32 b, int offset);
diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c b/drivers/i2c/busses/i2c-designware-platdrv.c
index ba142d7c0e05..68619b270b4c 100644
--- a/drivers/i2c/busses/i2c-designware-platdrv.c
+++ b/drivers/i2c/busses/i2c-designware-platdrv.c
@@ -158,11 +158,48 @@ static inline int dw_i2c_acpi_configure(struct platform_device *pdev)
 #endif
 
 #ifdef CONFIG_OF
+#define MSCC_ICPU_CFG_TWI_DELAY		0x0
+#define MSCC_ICPU_CFG_TWI_DELAY_ENABLE	BIT(0)
+#define MSCC_ICPU_CFG_TWI_SPIKE_FILTER	0x4
+
+static int mscc_twi_set_sda_hold_time(struct dw_i2c_dev *dev)
+{
+	writel((dev->sda_hold_time << 1) | MSCC_ICPU_CFG_TWI_DELAY_ENABLE,
+	       dev->ext + MSCC_ICPU_CFG_TWI_DELAY);
+
+	return 0;
+}
+
+int dw_i2c_of_configure(struct platform_device *pdev)
+{
+	struct dw_i2c_dev *dev = platform_get_drvdata(pdev);
+	struct resource *mem;
+
+	switch (dev->flags & MODEL_MASK) {
+	case MODEL_MSCC_OCELOT:
+		mem = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+		dev->ext = devm_ioremap_resource(&pdev->dev, mem);
+		if (!IS_ERR(dev->ext))
+			dev->set_sda_hold_time = mscc_twi_set_sda_hold_time;
+		break;
+	default:
+		break;
+	}
+
+	return 0;
+}
+
 static const struct of_device_id dw_i2c_of_match[] = {
 	{ .compatible = "snps,designware-i2c", },
+	{ .compatible = "mscc,ocelot-i2c", .data = (void *)MODEL_MSCC_OCELOT },
 	{},
 };
 MODULE_DEVICE_TABLE(of, dw_i2c_of_match);
+#else
+static inline int dw_i2c_of_configure(struct platform_device *pdev)
+{
+	return -ENODEV;
+}
 #endif
 
 static void i2c_dw_configure_master(struct dw_i2c_dev *dev)
@@ -275,6 +312,9 @@ static int dw_i2c_plat_probe(struct platform_device *pdev)
 
 	dev->flags |= (u32)device_get_match_data(&pdev->dev);
 
+	if (pdev->dev.of_node)
+		dw_i2c_of_configure(pdev);
+
 	acpi_speed = i2c_acpi_find_bus_speed(&pdev->dev);
 	/*
 	 * Some DSTDs use a non standard speed, round down to the lowest
-- 
2.18.0




[Index of Archives]     [Linux GPIO]     [Linux SPI]     [Linux Hardward Monitoring]     [LM Sensors]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux