Hi,
On Wed, Jun 13, 2018 at 12:34:46AM +0900, Akinobu Mita wrote:
> (This is 2nd version of SCCB helpers patch. After 1st version was
> submitted, I sent alternative patch titled "i2c: add I2C_M_FORCE_STOP".
> But it wasn't accepted because it makes the I2C core code unreadable.
> I couldn't find out a way to untangle it, so I returned to the original
> approach.)
>
> This adds Serial Camera Control Bus (SCCB) helper functions (sccb_read_byte
> and sccb_write_byte) that are intended to be used by some of Omnivision
> sensor drivers.
>
> The ov772x driver is going to use these functions in order to make it work
> with most i2c controllers.
>
> As the ov772x device doesn't support repeated starts, this driver currently
> requires I2C_FUNC_PROTOCOL_MANGLING that is not supported by many i2c
> controller drivers.
>
> With the sccb_read_byte() that issues two separated requests in order to
> avoid repeated start, the driver doesn't require I2C_FUNC_PROTOCOL_MANGLING.
>
> Cc: Sebastian Reichel <sebastian.reichel@xxxxxxxxxxxxxxx>
> Cc: Wolfram Sang <wsa@xxxxxxxxxxxxx>
> Cc: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
> Cc: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> Cc: Hans Verkuil <hans.verkuil@xxxxxxxxx>
> Cc: Sakari Ailus <sakari.ailus@xxxxxxxxxxxxxxx>
> Cc: Mauro Carvalho Chehab <mchehab@xxxxxxxxxxxxxxxx>
> Signed-off-by: Akinobu Mita <akinobu.mita@xxxxxxxxx>
> ---
Reviewed-by: Sebastian Reichel <sebastian.reichel@xxxxxxxxxxxxxxx>
-- Sebastian
> * v2
> - Convert all helpers into static inline functions, and remove C source
> and Kconfig option.
> - Acquire i2c adapter lock while issuing two requests for sccb_read_byte
>
> drivers/media/i2c/sccb.h | 74 ++++++++++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 74 insertions(+)
> create mode 100644 drivers/media/i2c/sccb.h
>
> diff --git a/drivers/media/i2c/sccb.h b/drivers/media/i2c/sccb.h
> new file mode 100644
> index 0000000..a531fdc
> --- /dev/null
> +++ b/drivers/media/i2c/sccb.h
> @@ -0,0 +1,74 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Serial Camera Control Bus (SCCB) helper functions
> + */
> +
> +#ifndef __SCCB_H__
> +#define __SCCB_H__
> +
> +#include <linux/i2c.h>
> +
> +/**
> + * sccb_read_byte - Read data from SCCB slave device
> + * @client: Handle to slave device
> + * @addr: Register to be read from
> + *
> + * This executes the 2-phase write transmission cycle that is followed by a
> + * 2-phase read transmission cycle, returning negative errno else a data byte
> + * received from the device.
> + */
> +static inline int sccb_read_byte(struct i2c_client *client, u8 addr)
> +{
> + u8 val;
> + struct i2c_msg msg[] = {
> + {
> + .addr = client->addr,
> + .len = 1,
> + .buf = &addr,
> + },
> + {
> + .addr = client->addr,
> + .flags = I2C_M_RD,
> + .len = 1,
> + .buf = &val,
> + },
> + };
> + int ret;
> + int i;
> +
> + i2c_lock_adapter(client->adapter);
> +
> + /* Issue two separated requests in order to avoid repeated start */
> + for (i = 0; i < 2; i++) {
> + ret = __i2c_transfer(client->adapter, &msg[i], 1);
> + if (ret != 1)
> + break;
> + }
> +
> + i2c_unlock_adapter(client->adapter);
> +
> + return i == 2 ? val : ret;
> +}
> +
> +/**
> + * sccb_write_byte - Write data to SCCB slave device
> + * @client: Handle to slave device
> + * @addr: Register to write to
> + * @data: Value to be written
> + *
> + * This executes the SCCB 3-phase write transmission cycle, returning negative
> + * errno else zero on success.
> + */
> +static inline int sccb_write_byte(struct i2c_client *client, u8 addr, u8 data)
> +{
> + int ret;
> + unsigned char msgbuf[] = { addr, data };
> +
> + ret = i2c_master_send(client, msgbuf, 2);
> + if (ret < 0)
> + return ret;
> +
> + return 0;
> +}
> +
> +#endif /* __SCCB_H__ */
> --
> 2.7.4
>
Attachment:
signature.asc
Description: PGP signature
