On Wed, Jan 18, 2017 at 04:57:12PM +0100, Peter Rosin wrote:
> Analog Devices ADG792A/G is a triple 4:1 mux.
>
> Acked-by: Jonathan Cameron <jic23@xxxxxxxxxx>
> Signed-off-by: Peter Rosin <peda@xxxxxxxxxx>
> ---
> .../devicetree/bindings/mux/mux-adg792a.txt | 79 ++++++++++++++++++++++
> 1 file changed, 79 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mux/mux-adg792a.txt
>
> diff --git a/Documentation/devicetree/bindings/mux/mux-adg792a.txt b/Documentation/devicetree/bindings/mux/mux-adg792a.txt
> new file mode 100644
> index 000000000000..0b26dd11f070
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mux/mux-adg792a.txt
> @@ -0,0 +1,79 @@
> +Bindings for Analog Devices ADG792A/G Triple 4:1 Multiplexers
> +
> +Required properties:
> +- compatible : "adi,adg792a" or "adi,adg792g"
> +- #mux-control-cells : <0> if parallel, or <1> if not.
> +* Standard mux-controller bindings as decribed in mux-controller.txt
> +
> +Optional properties for ADG792G:
> +- gpio-controller : if present, #gpio-cells below is required.
> +- #gpio-cells : should be <2>
> + - First cell is the GPO line number, i.e. 0 or 1
> + - Second cell is used to specify active high (0)
> + or active low (1)
> +
> +Optional properties:
> +- adi,parallel : if present, the three muxes are bound together with a single
> + mux controller, controlling all three muxes in parallel.
Can't this be implied by #mux-control-cells == 0?
> +- adi,idle-state : if present, array of 2-tuples with mux controller number
> + and state that mux controllers will have when idle. States 0 through 3
> + correspond to signals A through D in the datasheet.
> +- adi,idle-high-impedance : if present, array of mux controller numbers that
> + should be in the disconnected high-impedance state when idle.
Perhaps combine these 2 to a common idle-state with the index being the
mux controller number and a value of -1 (or 4) being hi-Z.
> +
> +Mux controller states 0 through 3 correspond to signals A through D in the
> +datasheet. If a mux controller is mentioned in neither adi,idle-state nor
> +adi,idle-high-impedance it is left in its previously selected state when idle.
> +
> +Example:
> +
> + /*
> + * Three independent mux controllers (of which one is used).
> + * Mux 0 is disconnected when idle, mux 1 idles with signal C
> + * and mux 2 idles with signal A.
> + */
> + &i2c0 {
> + mux: adg792a@50 {
mux-controller@50
> + compatible = "adi,adg792a";
> + reg = <0x50>;
> + #mux-control-cells = <1>;
> +
> + adi,idle-high-impedance = <0>;
> + adi,idle-state = <1 2>, <2 0>;
> + };
> + };
> +
> + adc-mux {
> + compatible = "io-channel-mux";
> + io-channels = <&adc 0>;
> + io-channel-names = "parent";
> +
> + mux-controls = <&mux 1>;
> +
> + channels = "sync-1", "", "out";
> + };
> +
> +
> + /*
> + * Three parallel muxes with one mux controller, useful e.g. if
> + * the adc is differential, thus needing two signals to be muxed
> + * simultaneously for correct operation.
> + */
> + &i2c0 {
> + pmux: adg792a@50 {
> + compatible = "adi,adg792a";
> + reg = <0x50>;
> + #mux-control-cells = <0>;
> + adi,parallel;
> + };
> + };
> +
> + diff-adc-mux {
> + compatible = "io-channel-mux";
> + io-channels = <&adc 0>;
> + io-channel-names = "parent";
> +
> + mux-controls = <&pmux>;
> +
> + channels = "sync-1", "", "out";
> + };
> --
> 2.1.4
>
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-i2c" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
