From: Tin Huynh <tnhuynh@xxxxxxx>
Free and Open IPMI use SMBUS BLOCK Read/Write to support SSIF protocol.
However, I2C Designwave Core Driver doesn't handle the case at the moment.
The below patch supports this feature.
Change from V1:
-Remove empty lines
-Add flags variable to make clean code
-Change DW_DEFAULT_FUNCTIONALITY in i2c-designware-pcidrv.c
Signed-off-by: Tin Huynh <tnhuynh@xxxxxxx>
---
drivers/i2c/busses/i2c-designware-core.c | 36 ++++++++++++++++++++++++--
drivers/i2c/busses/i2c-designware-pcidrv.c | 1 +
drivers/i2c/busses/i2c-designware-platdrv.c | 1 +
3 files changed, 35 insertions(+), 3 deletions(-)
diff --git a/drivers/i2c/busses/i2c-designware-core.c b/drivers/i2c/busses/i2c-designware-core.c
index 1fe93c4..c77a83f 100644
--- a/drivers/i2c/busses/i2c-designware-core.c
+++ b/drivers/i2c/busses/i2c-designware-core.c
@@ -543,6 +543,7 @@ static void i2c_dw_xfer_init(struct dw_i2c_dev *dev)
intr_mask = DW_IC_INTR_DEFAULT_MASK;
for (; dev->msg_write_idx < dev->msgs_num; dev->msg_write_idx++) {
+ u32 flags = msgs[dev->msg_write_idx].flags;
/*
* if target address has changed, we need to
* reprogram the target address in the i2c
@@ -588,8 +589,15 @@ static void i2c_dw_xfer_init(struct dw_i2c_dev *dev)
* detected from the registers so we set it always
* when writing/reading the last byte.
*/
+
+ /*
+ * i2c-core.c always set the buffer length of
+ * I2C_FUNC_SMBUS_BLOCK_DATA to 1. The length will
+ * be adjusted when receiving the first byte.
+ * Thus we can't stop the transaction here.
+ */
if (dev->msg_write_idx == dev->msgs_num - 1 &&
- buf_len == 1)
+ buf_len == 1 && !(flags & I2C_M_RECV_LEN))
cmd |= BIT(9);
if (need_restart) {
@@ -614,7 +622,12 @@ static void i2c_dw_xfer_init(struct dw_i2c_dev *dev)
dev->tx_buf = buf;
dev->tx_buf_len = buf_len;
- if (buf_len > 0) {
+ /*
+ * Because we don't know the buffer length in the
+ * I2C_FUNC_SMBUS_BLOCK_DATA case, we can't stop
+ * the transaction here.
+ */
+ if (buf_len > 0 || flags & I2C_M_RECV_LEN) {
/* more bytes to be written */
dev->status |= STATUS_WRITE_IN_PROGRESS;
break;
@@ -659,7 +672,24 @@ static void i2c_dw_xfer_init(struct dw_i2c_dev *dev)
rx_valid = dw_readl(dev, DW_IC_RXFLR);
for (; len > 0 && rx_valid > 0; len--, rx_valid--) {
- *buf++ = dw_readl(dev, DW_IC_DATA_CMD);
+ u32 flags = msgs[dev->msg_read_idx].flags;
+ *buf = dw_readl(dev, DW_IC_DATA_CMD);
+ /* ensure length byte is a valid value */
+ if (flags & I2C_M_RECV_LEN &&
+ *buf <= I2C_SMBUS_BLOCK_MAX && *buf > 0) {
+ /*
+ * Adjust the buffer length and mask the flag
+ * after receiving the first byte
+ */
+ len = (flags & I2C_CLIENT_PEC) ?
+ *buf + 2 : *buf + 1;
+ dev->tx_buf_len = len > dev->rx_outstanding ?
+ len - dev->rx_outstanding : 0;
+ msgs[dev->msg_read_idx].len = len;
+ flags &= ~I2C_M_RECV_LEN;
+ msgs[dev->msg_read_idx].flags = flags;
+ }
+ buf++;
dev->rx_outstanding--;
}
diff --git a/drivers/i2c/busses/i2c-designware-pcidrv.c b/drivers/i2c/busses/i2c-designware-pcidrv.c
index 96f8230..8ffe2da 100644
--- a/drivers/i2c/busses/i2c-designware-pcidrv.c
+++ b/drivers/i2c/busses/i2c-designware-pcidrv.c
@@ -75,6 +75,7 @@ struct dw_pci_controller {
I2C_FUNC_SMBUS_BYTE | \
I2C_FUNC_SMBUS_BYTE_DATA | \
I2C_FUNC_SMBUS_WORD_DATA | \
+ I2C_FUNC_SMBUS_BLOCK_DATA | \
I2C_FUNC_SMBUS_I2C_BLOCK)
/* Merrifield HCNT/LCNT/SDA hold time */
diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c b/drivers/i2c/busses/i2c-designware-platdrv.c
index 0b42a12..886fb62 100644
--- a/drivers/i2c/busses/i2c-designware-platdrv.c
+++ b/drivers/i2c/busses/i2c-designware-platdrv.c
@@ -220,6 +220,7 @@ static int dw_i2c_plat_probe(struct platform_device *pdev)
I2C_FUNC_SMBUS_BYTE |
I2C_FUNC_SMBUS_BYTE_DATA |
I2C_FUNC_SMBUS_WORD_DATA |
+ I2C_FUNC_SMBUS_BLOCK_DATA |
I2C_FUNC_SMBUS_I2C_BLOCK;
dev->master_cfg = DW_IC_CON_MASTER | DW_IC_CON_SLAVE_DISABLE |
--
1.7.1
--
To unsubscribe from this list: send the line "unsubscribe linux-i2c" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
