add Hisilicon BVT I2C controller driver support.
Signed-off-by: Pan Wen <wenpan@xxxxxxxxxxxxx>
---
change log
v4:
Modify the default frequency to 100KHz.
v3:
Add a SoC specific compatible string.
v2:
1)Fixed a compile error.
2)Dropped the clock-names property.
.../devicetree/bindings/i2c/i2c-hibvt.txt | 24 +
drivers/i2c/busses/Kconfig | 10 +
drivers/i2c/busses/Makefile | 1 +
drivers/i2c/busses/i2c-hibvt.c | 737 +++++++++++++++++++++
4 files changed, 772 insertions(+)
create mode 100644 Documentation/devicetree/bindings/i2c/i2c-hibvt.txt
create mode 100644 drivers/i2c/busses/i2c-hibvt.c
diff --git a/Documentation/devicetree/bindings/i2c/i2c-hibvt.txt b/Documentation/devicetree/bindings/i2c/i2c-hibvt.txt
new file mode 100644
index 0000000..db3d2e2
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-hibvt.txt
@@ -0,0 +1,24 @@
+Hisilicon BVT I2C master controller
+
+Required properties:
+- compatible: should be "hisilicon,hibvt-i2c" and one of the following:
+ "hisilicon,hi3516cv300-i2c"
+- reg: physical base address of the controller and length of memory mapped.
+ region.
+- interrupts: interrupt number to the cpu.
+- clocks: phandles to input clocks.
+
+Optional properties:
+- clock-frequency: Desired I2C bus frequency in Hz, otherwise defaults to 100000.
+
+Other properties:
+see Documentation/devicetree/bindings/i2c/i2c.txt.
+
+Examples:
+i2c_bus0: i2c@12110000 {
+ compatible = "hisilicon,hi3516cv300-i2c", "hisilicon,hibvt-i2c";
+ reg = <0x12110000 0x100>;
+ interrupts = <20>;
+ clocks = <&crg_ctrl HI3516CV300_APB_CLK>;
+ clock-frequency = <100000>;
+};
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 5c3993b..fc1b679 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -555,6 +555,16 @@ config I2C_GPIO
This is a very simple bitbanging I2C driver utilizing the
arch-neutral GPIO API to control the SCL and SDA lines.
+config I2C_HIBVT
+ tristate "Hisilicon BVT I2C Controller"
+ depends on ARCH_HISI
+ help
+ Say Y here to include support for Hisilicon BVT I2C controller in the
+ Hisilicon BVT SoCs.
+
+ This driver can also be built as a module. If so, the module
+ will be called i2c-hibvt.
+
config I2C_HIGHLANDER
tristate "Highlander FPGA SMBus interface"
depends on SH_HIGHLANDER
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index 37f2819..42ef2e0 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -51,6 +51,7 @@ obj-$(CONFIG_I2C_EG20T) += i2c-eg20t.o
obj-$(CONFIG_I2C_EMEV2) += i2c-emev2.o
obj-$(CONFIG_I2C_EXYNOS5) += i2c-exynos5.o
obj-$(CONFIG_I2C_GPIO) += i2c-gpio.o
+obj-$(CONFIG_I2C_HIBVT) += i2c-hibvt.o
obj-$(CONFIG_I2C_HIGHLANDER) += i2c-highlander.o
obj-$(CONFIG_I2C_HIX5HD2) += i2c-hix5hd2.o
obj-$(CONFIG_I2C_IBM_IIC) += i2c-ibm_iic.o
diff --git a/drivers/i2c/busses/i2c-hibvt.c b/drivers/i2c/busses/i2c-hibvt.c
new file mode 100644
index 0000000..e8af63e
--- /dev/null
+++ b/drivers/i2c/busses/i2c-hibvt.c
@@ -0,0 +1,737 @@
+/*
+ * Hisilicon BVT I2C Controller Driver
+ *
+ * Copyright (c) 2016 HiSilicon Technologies Co., Ltd.
+ *
+ * Authors: wenpan@xxxxxxxxxxxxx
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+/*
+ * I2C Registers offsets
+ */
+#define HIBVT_I2C_GLB 0x0
+#define HIBVT_I2C_SCL_H 0x4
+#define HIBVT_I2C_SCL_L 0x8
+#define HIBVT_I2C_DATA1 0x10
+#define HIBVT_I2C_TXF 0x20
+#define HIBVT_I2C_RXF 0x24
+#define HIBVT_I2C_CMD_BASE 0x30
+#define HIBVT_I2C_LOOP1 0xb0
+#define HIBVT_I2C_DST1 0xb4
+#define HIBVT_I2C_TX_WATER 0xc8
+#define HIBVT_I2C_RX_WATER 0xcc
+#define HIBVT_I2C_CTRL1 0xd0
+#define HIBVT_I2C_STAT 0xd8
+#define HIBVT_I2C_INTR_RAW 0xe0
+#define HIBVT_I2C_INTR_EN 0xe4
+#define HIBVT_I2C_INTR_STAT 0xe8
+
+/*
+ * I2C Global Config Register -- HIBVT_I2C_GLB
+ */
+#define GLB_EN_MASK BIT(0)
+#define GLB_SDA_HOLD_MASK GENMASK(23, 8)
+#define GLB_SDA_HOLD_SHIFT (8)
+
+/*
+ * I2C Timing CMD Register -- HIBVT_I2C_CMD_BASE + n * 4 (n = 0, 1, 2, ... 31)
+ */
+#define CMD_EXIT 0x0
+#define CMD_TX_S 0x1
+#define CMD_TX_D1_2 0x4
+#define CMD_TX_D1_1 0x5
+#define CMD_TX_FIFO 0x9
+#define CMD_RX_FIFO 0x12
+#define CMD_RX_ACK 0x13
+#define CMD_IGN_ACK 0x15
+#define CMD_TX_ACK 0x16
+#define CMD_TX_NACK 0x17
+#define CMD_JMP1 0x18
+#define CMD_UP_TXF 0x1d
+#define CMD_TX_RS 0x1e
+#define CMD_TX_P 0x1f
+
+/*
+ * I2C Control Register 1 -- HIBVT_I2C_CTRL1
+ */
+#define CTRL1_CMD_START_MASK BIT(0)
+
+/*
+ * I2C Status Register -- HIBVT_I2C_STAT
+ */
+#define STAT_RXF_NOE_MASK BIT(16) /* RX FIFO not empty flag */
+#define STAT_TXF_NOF_MASK BIT(19) /* TX FIFO not full flag */
+
+
+/*
+ * I2C Interrupt status and mask Register --
+ * HIBVT_I2C_INTR_RAW, HIBVT_I2C_STAT, HIBVT_I2C_INTR_STAT
+ */
+#define INTR_ABORT_MASK (BIT(0) | BIT(11))
+#define INTR_RX_MASK BIT(2)
+#define INTR_TX_MASK BIT(4)
+#define INTR_CMD_DONE_MASK BIT(12)
+#define INTR_USE_MASK (INTR_ABORT_MASK \
+ |INTR_RX_MASK \
+ | INTR_TX_MASK \
+ | INTR_CMD_DONE_MASK)
+#define INTR_ALL_MASK GENMASK(31, 0)
+
+#define I2C_DEFAULT_FREQUENCY 100000
+#define I2C_TXF_DEPTH 64
+#define I2C_RXF_DEPTH 64
+#define I2C_TXF_WATER 32
+#define I2C_RXF_WATER 32
+#define I2C_WAIT_TIMEOUT 0x10000
+#define I2C_IRQ_TIMEOUT (msecs_to_jiffies(1000))
+
+
+struct hibvt_i2c_dev {
+ struct device *dev;
+ struct i2c_adapter adap;
+ void __iomem *base;
+ struct clk *clk;
+ int irq;
+
+ unsigned int freq;
+ struct i2c_msg *msg;
+ unsigned int msg_num;
+ unsigned int msg_idx;
+ unsigned int msg_buf_ptr;
+ struct completion msg_complete;
+
+ spinlock_t lock;
+ int status;
+};
+
+static inline void hibvt_i2c_disable(struct hibvt_i2c_dev *i2c)
+{
+ unsigned int val;
+
+ val = readl(i2c->base + HIBVT_I2C_GLB);
+ val &= ~GLB_EN_MASK;
+ writel(val, i2c->base + HIBVT_I2C_GLB);
+}
+
+static inline void hibvt_i2c_enable(struct hibvt_i2c_dev *i2c)
+{
+ unsigned int val;
+
+ val = readl(i2c->base + HIBVT_I2C_GLB);
+ val |= GLB_EN_MASK;
+ writel(val, i2c->base + HIBVT_I2C_GLB);
+}
+
+static inline void hibvt_i2c_cfg_irq(struct hibvt_i2c_dev *i2c,
+ unsigned int flag)
+{
+ writel(flag, i2c->base + HIBVT_I2C_INTR_EN);
+}
+
+static inline void hibvt_i2c_disable_irq(struct hibvt_i2c_dev *i2c,
+ unsigned int flag)
+{
+ unsigned int val;
+
+ val = readl(i2c->base + HIBVT_I2C_INTR_EN);
+ val &= ~flag;
+ writel(val, i2c->base + HIBVT_I2C_INTR_EN);
+}
+
+static inline unsigned int hibvt_i2c_clr_irq(struct hibvt_i2c_dev *i2c)
+{
+ unsigned int val;
+
+ val = readl(i2c->base + HIBVT_I2C_INTR_STAT);
+ writel(INTR_ALL_MASK, i2c->base + HIBVT_I2C_INTR_RAW);
+
+ return val;
+}
+
+static inline void hibvt_i2c_cmdreg_set(struct hibvt_i2c_dev *i2c,
+ unsigned int cmd, unsigned int *offset)
+{
+ dev_dbg(i2c->dev, "hii2c reg: offset=0x%x, cmd=0x%x...\n",
+ *offset * 4, cmd);
+ writel(cmd, i2c->base + HIBVT_I2C_CMD_BASE + *offset * 4);
+ (*offset)++;
+}
+
+/*
+ * config i2c slave addr
+ */
+static inline void hibvt_i2c_set_addr(struct hibvt_i2c_dev *i2c)
+{
+ struct i2c_msg *msg = i2c->msg;
+ u16 addr;
+
+ if (msg->flags & I2C_M_TEN) {
+ /* First byte is 11110XX0 where XX is upper 2 bits */
+ addr = ((msg->addr & 0x300) << 1) | 0xf000;
+ if (msg->flags & I2C_M_RD)
+ addr |= 1 << 8;
+
+ /* Second byte is the remaining 8 bits */
+ addr |= msg->addr & 0xff;
+ } else {
+ addr = (msg->addr & 0x7f) << 1;
+ if (msg->flags & I2C_M_RD)
+ addr |= 1;
+ }
+
+ writel(addr, i2c->base + HIBVT_I2C_DATA1);
+}
+
+/*
+ * Start command sequence
+ */
+static inline void hibvt_i2c_start_cmd(struct hibvt_i2c_dev *i2c)
+{
+ unsigned int val;
+
+ val = readl(i2c->base + HIBVT_I2C_CTRL1);
+ val |= CTRL1_CMD_START_MASK;
+ writel(val, i2c->base + HIBVT_I2C_CTRL1);
+}
+
+static int hibvt_i2c_wait_rx_noempty(struct hibvt_i2c_dev *i2c)
+{
+ unsigned int time_cnt = 0;
+ unsigned int val;
+
+ do {
+ val = readl(i2c->base + HIBVT_I2C_STAT);
+ if (val & STAT_RXF_NOE_MASK)
+ return 0;
+
+ udelay(50);
+ } while (time_cnt++ < I2C_WAIT_TIMEOUT);
+
+ dev_err(i2c->dev, "wait rx no empty timeout, RIS: 0x%x, SR: 0x%x\n",
+ readl(i2c->base + HIBVT_I2C_INTR_RAW), val);
+ return -EIO;
+}
+
+static int hibvt_i2c_wait_tx_nofull(struct hibvt_i2c_dev *i2c)
+{
+ unsigned int time_cnt = 0;
+ unsigned int val;
+
+ do {
+ val = readl(i2c->base + HIBVT_I2C_STAT);
+ if (val & STAT_TXF_NOF_MASK)
+ return 0;
+
+ udelay(50);
+ } while (time_cnt++ < I2C_WAIT_TIMEOUT);
+
+ dev_err(i2c->dev, "wait rx no empty timeout, RIS: 0x%x, SR: 0x%x\n",
+ readl(i2c->base + HIBVT_I2C_INTR_RAW), val);
+ return -EIO;
+}
+
+static int hibvt_i2c_wait_idle(struct hibvt_i2c_dev *i2c)
+{
+ unsigned int time_cnt = 0;
+ unsigned int val;
+
+ do {
+ val = readl(i2c->base + HIBVT_I2C_INTR_RAW);
+ if (val & (INTR_ABORT_MASK)) {
+ dev_err(i2c->dev, "wait idle abort!, RIS: 0x%x\n",
+ val);
+ return -EIO;
+ }
+
+ if (val & INTR_CMD_DONE_MASK)
+ return 0;
+
+ udelay(50);
+ } while (time_cnt++ < I2C_WAIT_TIMEOUT);
+
+ dev_err(i2c->dev, "wait idle timeout, RIS: 0x%x, SR: 0x%x\n",
+ val, readl(i2c->base + HIBVT_I2C_STAT));
+
+ return -EIO;
+}
+
+static void hibvt_i2c_set_freq(struct hibvt_i2c_dev *i2c)
+{
+ unsigned int max_freq, freq;
+ unsigned int clk_rate;
+ unsigned int val, sda_hold;
+
+ freq = i2c->freq;
+ clk_rate = clk_get_rate(i2c->clk);
+ max_freq = clk_rate >> 1;
+
+ if (freq > max_freq) {
+ i2c->freq = max_freq;
+ freq = i2c->freq;
+ }
+
+ if (freq <= 100000) {
+ val = clk_rate / (freq * 2) - 1;
+ writel(val, i2c->base + HIBVT_I2C_SCL_H);
+ writel(val, i2c->base + HIBVT_I2C_SCL_L);
+ } else {
+ val = (clk_rate * 36) / (freq * 100);
+ writel(val, i2c->base + HIBVT_I2C_SCL_H);
+ val = (clk_rate * 64) / (freq * 100);
+ writel(val, i2c->base + HIBVT_I2C_SCL_L);
+ }
+
+ sda_hold = val * 3 / 10;
+ sda_hold = (sda_hold << GLB_SDA_HOLD_SHIFT) & GLB_SDA_HOLD_MASK;
+ val = readl(i2c->base + HIBVT_I2C_GLB);
+ val &= ~GLB_SDA_HOLD_MASK;
+ val |= sda_hold;
+ writel(val, i2c->base + HIBVT_I2C_GLB);
+}
+
+/*
+ * set i2c controller TX and RX FIFO water
+ */
+static inline void hibvt_i2c_set_water(struct hibvt_i2c_dev *i2c)
+{
+ writel(I2C_TXF_WATER, i2c->base + HIBVT_I2C_TX_WATER);
+ writel(I2C_RXF_WATER, i2c->base + HIBVT_I2C_RX_WATER);
+}
+
+/*
+ * initialise the controller, set i2c bus interface freq
+ */
+static void hibvt_i2c_hw_init(struct hibvt_i2c_dev *i2c)
+{
+ hibvt_i2c_disable(i2c);
+ hibvt_i2c_disable_irq(i2c, INTR_ALL_MASK);
+ hibvt_i2c_set_freq(i2c);
+ hibvt_i2c_set_water(i2c);
+}
+
+/*
+ * hibvt_i2c_cfg_cmd - config i2c controller command sequence
+ *
+ * After all the timing command is configured,
+ * and then start the command, you can i2c communication,
+ * and then only need to read and write i2c fifo.
+ */
+static void hibvt_i2c_cfg_cmd(struct hibvt_i2c_dev *i2c)
+{
+ struct i2c_msg *msg = i2c->msg;
+ int offset = 0;
+
+ if (i2c->msg_idx == 0)
+ hibvt_i2c_cmdreg_set(i2c, CMD_TX_S, &offset);
+ else
+ hibvt_i2c_cmdreg_set(i2c, CMD_TX_RS, &offset);
+
+ if (msg->flags & I2C_M_TEN) {
+ if (i2c->msg_idx == 0) {
+ hibvt_i2c_cmdreg_set(i2c, CMD_TX_D1_2, &offset);
+ hibvt_i2c_cmdreg_set(i2c, CMD_TX_D1_1, &offset);
+ } else {
+ hibvt_i2c_cmdreg_set(i2c, CMD_TX_D1_2, &offset);
+ }
+ } else {
+ hibvt_i2c_cmdreg_set(i2c, CMD_TX_D1_1, &offset);
+ }
+
+ if (msg->flags & I2C_M_IGNORE_NAK)
+ hibvt_i2c_cmdreg_set(i2c, CMD_IGN_ACK, &offset);
+ else
+ hibvt_i2c_cmdreg_set(i2c, CMD_RX_ACK, &offset);
+
+ if (msg->flags & I2C_M_RD) {
+ if (msg->len >= 2) {
+ writel(offset, i2c->base + HIBVT_I2C_DST1);
+ writel(msg->len - 2, i2c->base + HIBVT_I2C_LOOP1);
+ hibvt_i2c_cmdreg_set(i2c, CMD_RX_FIFO, &offset);
+ hibvt_i2c_cmdreg_set(i2c, CMD_TX_ACK, &offset);
+ hibvt_i2c_cmdreg_set(i2c, CMD_JMP1, &offset);
+ }
+ hibvt_i2c_cmdreg_set(i2c, CMD_RX_FIFO, &offset);
+ hibvt_i2c_cmdreg_set(i2c, CMD_TX_NACK, &offset);
+ } else {
+ writel(offset, i2c->base + HIBVT_I2C_DST1);
+ writel(msg->len - 1, i2c->base + HIBVT_I2C_LOOP1);
+ hibvt_i2c_cmdreg_set(i2c, CMD_UP_TXF, &offset);
+ hibvt_i2c_cmdreg_set(i2c, CMD_TX_FIFO, &offset);
+
+ if (msg->flags & I2C_M_IGNORE_NAK)
+ hibvt_i2c_cmdreg_set(i2c, CMD_IGN_ACK, &offset);
+ else
+ hibvt_i2c_cmdreg_set(i2c, CMD_RX_ACK, &offset);
+
+ hibvt_i2c_cmdreg_set(i2c, CMD_JMP1, &offset);
+ }
+
+ if ((i2c->msg_idx == (i2c->msg_num - 1)) || (msg->flags & I2C_M_STOP)) {
+ dev_dbg(i2c->dev, "run to %s %d...TX STOP\n",
+ __func__, __LINE__);
+ hibvt_i2c_cmdreg_set(i2c, CMD_TX_P, &offset);
+ }
+
+ hibvt_i2c_cmdreg_set(i2c, CMD_EXIT, &offset);
+}
+
+static int hibvt_i2c_polling_xfer_one_msg(struct hibvt_i2c_dev *i2c)
+{
+ int status;
+ unsigned int val;
+ struct i2c_msg *msg = i2c->msg;
+
+ dev_dbg(i2c->dev, "[%s,%d]msg->flags=0x%x, len=0x%x\n",
+ __func__, __LINE__, msg->flags, msg->len);
+
+ hibvt_i2c_enable(i2c);
+ hibvt_i2c_clr_irq(i2c);
+ hibvt_i2c_set_addr(i2c);
+ hibvt_i2c_cfg_cmd(i2c);
+ hibvt_i2c_start_cmd(i2c);
+
+ i2c->msg_buf_ptr = 0;
+
+ if (msg->flags & I2C_M_RD) {
+ while (i2c->msg_buf_ptr < msg->len) {
+ status = hibvt_i2c_wait_rx_noempty(i2c);
+ if (status)
+ goto end;
+
+ val = readl(i2c->base + HIBVT_I2C_RXF);
+ msg->buf[i2c->msg_buf_ptr] = val;
+ i2c->msg_buf_ptr++;
+
+ }
+ } else {
+ while (i2c->msg_buf_ptr < msg->len) {
+ status = hibvt_i2c_wait_tx_nofull(i2c);
+ if (status)
+ goto end;
+
+ val = msg->buf[i2c->msg_buf_ptr];
+ writel(val, i2c->base + HIBVT_I2C_TXF);
+ i2c->msg_buf_ptr++;
+ }
+ }
+
+ status = hibvt_i2c_wait_idle(i2c);
+end:
+ hibvt_i2c_disable(i2c);
+
+ return status;
+}
+
+static irqreturn_t hibvt_i2c_isr(int irq, void *dev_id)
+{
+ struct hibvt_i2c_dev *i2c = dev_id;
+ unsigned int irq_status;
+ struct i2c_msg *msg = i2c->msg;
+
+ spin_lock(&i2c->lock);
+
+ irq_status = hibvt_i2c_clr_irq(i2c);
+ dev_dbg(i2c->dev, "%s RIS: 0x%x\n", __func__, irq_status);
+
+ if (!irq_status) {
+ dev_dbg(i2c->dev, "no irq\n");
+ goto end;
+ }
+
+ if (irq_status & INTR_ABORT_MASK) {
+ dev_err(i2c->dev, "irq handle abort, RIS: 0x%x\n",
+ irq_status);
+ i2c->status = -EIO;
+ hibvt_i2c_disable_irq(i2c, INTR_ALL_MASK);
+
+ complete(&i2c->msg_complete);
+ goto end;
+ }
+
+ if (msg->flags & I2C_M_RD) {
+ while ((readl(i2c->base + HIBVT_I2C_STAT) & STAT_RXF_NOE_MASK)
+ && (i2c->msg_buf_ptr < msg->len)) {
+ msg->buf[i2c->msg_buf_ptr] =
+ readl(i2c->base + HIBVT_I2C_RXF);
+ i2c->msg_buf_ptr++;
+ }
+ } else {
+ while ((readl(i2c->base + HIBVT_I2C_STAT) & STAT_TXF_NOF_MASK)
+ && (i2c->msg_buf_ptr < msg->len)) {
+ writel(msg->buf[i2c->msg_buf_ptr],
+ i2c->base + HIBVT_I2C_TXF);
+ i2c->msg_buf_ptr++;
+ }
+ }
+
+ if (i2c->msg_buf_ptr >= msg->len)
+ hibvt_i2c_disable_irq(i2c, INTR_TX_MASK | INTR_RX_MASK);
+
+ if (irq_status & INTR_CMD_DONE_MASK) {
+ dev_dbg(i2c->dev, "cmd done\n");
+ i2c->status = 0;
+ hibvt_i2c_disable_irq(i2c, INTR_ALL_MASK);
+
+ complete(&i2c->msg_complete);
+ }
+
+end:
+ spin_unlock(&i2c->lock);
+
+ return IRQ_HANDLED;
+}
+
+static int hibvt_i2c_interrupt_xfer_one_msg(struct hibvt_i2c_dev *i2c)
+{
+ int status;
+ struct i2c_msg *msg = i2c->msg;
+ unsigned long timeout;
+ unsigned long flags;
+
+ dev_dbg(i2c->dev, "[%s,%d]msg->flags=0x%x, len=0x%x\n",
+ __func__, __LINE__, msg->flags, msg->len);
+
+ reinit_completion(&i2c->msg_complete);
+ i2c->msg_buf_ptr = 0;
+ i2c->status = -EIO;
+
+ spin_lock_irqsave(&i2c->lock, flags);
+ hibvt_i2c_enable(i2c);
+ hibvt_i2c_clr_irq(i2c);
+ if (msg->flags & I2C_M_RD)
+ hibvt_i2c_cfg_irq(i2c, INTR_USE_MASK & ~INTR_TX_MASK);
+ else
+ hibvt_i2c_cfg_irq(i2c, INTR_USE_MASK & ~INTR_RX_MASK);
+
+ hibvt_i2c_set_addr(i2c);
+ hibvt_i2c_cfg_cmd(i2c);
+ hibvt_i2c_start_cmd(i2c);
+ spin_unlock_irqrestore(&i2c->lock, flags);
+
+ timeout = wait_for_completion_timeout(&i2c->msg_complete,
+ I2C_IRQ_TIMEOUT);
+
+ if (timeout == 0) {
+ hibvt_i2c_disable_irq(i2c, INTR_ALL_MASK);
+ status = -EIO;
+ dev_err(i2c->dev, "%s timeout\n",
+ msg->flags & I2C_M_RD ? "rx" : "tx");
+ } else {
+ status = i2c->status;
+ }
+
+ hibvt_i2c_disable(i2c);
+
+ return status;
+}
+
+/*
+ * Master transfer function
+ */
+static int hibvt_i2c_xfer(struct i2c_adapter *adap,
+ struct i2c_msg *msgs, int num)
+{
+ struct hibvt_i2c_dev *i2c = i2c_get_adapdata(adap);
+ int status;
+
+ if (!msgs) {
+ dev_err(i2c->dev, "msgs == NULL\n");
+ return -EIO;
+ }
+
+ i2c->msg = msgs;
+ i2c->msg_num = num;
+ i2c->msg_idx = 0;
+
+ if (i2c->irq >= 0) {
+ while (i2c->msg_idx < i2c->msg_num) {
+ status = hibvt_i2c_interrupt_xfer_one_msg(i2c);
+ if (status)
+ break;
+
+ i2c->msg++;
+ i2c->msg_idx++;
+ }
+ } else {
+ while (i2c->msg_idx < i2c->msg_num) {
+ status = hibvt_i2c_polling_xfer_one_msg(i2c);
+ if (status)
+ break;
+
+ i2c->msg++;
+ i2c->msg_idx++;
+ }
+ }
+
+ if (!status || i2c->msg_idx > 0)
+ status = i2c->msg_idx;
+
+ return status;
+}
+
+static u32 hibvt_i2c_func(struct i2c_adapter *adap)
+{
+ return I2C_FUNC_I2C | I2C_FUNC_10BIT_ADDR
+ | I2C_FUNC_PROTOCOL_MANGLING;
+}
+
+static const struct i2c_algorithm hibvt_i2c_algo = {
+ .master_xfer = hibvt_i2c_xfer,
+ .functionality = hibvt_i2c_func,
+};
+
+static int hibvt_i2c_probe(struct platform_device *pdev)
+{
+ int status;
+ struct hibvt_i2c_dev *i2c;
+ struct i2c_adapter *adap;
+ struct resource *res;
+
+ i2c = devm_kzalloc(&pdev->dev, sizeof(*i2c), GFP_KERNEL);
+ if (!i2c)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, i2c);
+ i2c->dev = &pdev->dev;
+ spin_lock_init(&i2c->lock);
+ init_completion(&i2c->msg_complete);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ i2c->base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(i2c->base)) {
+ dev_err(i2c->dev, "cannot ioremap resource\n");
+ return -ENOMEM;
+ }
+
+ i2c->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(i2c->clk)) {
+ dev_err(i2c->dev, "cannot get clock\n");
+ return -ENOENT;
+ }
+ clk_prepare_enable(i2c->clk);
+
+ if (of_property_read_u32(pdev->dev.of_node, "clock-frequency",
+ &i2c->freq)) {
+ dev_warn(i2c->dev, "setting default clock-frequency@%dHz\n",
+ I2C_DEFAULT_FREQUENCY);
+ i2c->freq = I2C_DEFAULT_FREQUENCY;
+ }
+
+ /* i2c controller initialization, disable interrupt */
+ hibvt_i2c_hw_init(i2c);
+
+ i2c->irq = platform_get_irq(pdev, 0);
+ status = devm_request_irq(&pdev->dev, i2c->irq, hibvt_i2c_isr,
+ IRQF_SHARED, dev_name(&pdev->dev), i2c);
+ if (status) {
+ dev_dbg(i2c->dev, "falling back to polling mode");
+ i2c->irq = -1;
+ }
+
+ adap = &i2c->adap;
+ i2c_set_adapdata(adap, i2c);
+ adap->owner = THIS_MODULE;
+ strlcpy(adap->name, "hibvt-i2c", sizeof(adap->name));
+ adap->dev.parent = &pdev->dev;
+ adap->dev.of_node = pdev->dev.of_node;
+ adap->algo = &hibvt_i2c_algo;
+
+ /* Add the i2c adapter */
+ status = i2c_add_adapter(adap);
+ if (status) {
+ dev_err(i2c->dev, "failed to add bus to i2c core\n");
+ goto err_add_adapter;
+ }
+
+ dev_info(i2c->dev, "%s%d@%dhz registered\n",
+ adap->name, adap->nr, i2c->freq);
+
+ return 0;
+
+err_add_adapter:
+ clk_disable_unprepare(i2c->clk);
+ return status;
+}
+
+static int hibvt_i2c_remove(struct platform_device *pdev)
+{
+ struct hibvt_i2c_dev *i2c = platform_get_drvdata(pdev);
+
+ clk_disable_unprepare(i2c->clk);
+ i2c_del_adapter(&i2c->adap);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int hibvt_i2c_suspend(struct device *dev)
+{
+ struct hibvt_i2c_dev *i2c = dev_get_drvdata(dev);
+
+ i2c_lock_adapter(&i2c->adap);
+ clk_disable_unprepare(i2c->clk);
+ i2c_unlock_adapter(&i2c->adap);
+
+ return 0;
+}
+
+static int hibvt_i2c_resume(struct device *dev)
+{
+ struct hibvt_i2c_dev *i2c = dev_get_drvdata(dev);
+
+ i2c_lock_adapter(&i2c->adap);
+ clk_prepare_enable(i2c->clk);
+ hibvt_i2c_hw_init(i2c);
+ i2c_unlock_adapter(&i2c->adap);
+
+ return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(hibvt_i2c_dev_pm, hibvt_i2c_suspend,
+ hibvt_i2c_resume);
+
+static const struct of_device_id hibvt_i2c_match[] = {
+ { .compatible = "hisilicon,hibvt-i2c"},
+ { .compatible = "hisilicon,hi3516cv300-i2c"},
+ {},
+};
+MODULE_DEVICE_TABLE(of, hibvt_i2c_match);
+
+static struct platform_driver hibvt_i2c_driver = {
+ .driver = {
+ .name = "hibvt-i2c",
+ .of_match_table = hibvt_i2c_match,
+ .pm = &hibvt_i2c_dev_pm,
+ },
+ .probe = hibvt_i2c_probe,
+ .remove = hibvt_i2c_remove,
+};
+
+module_platform_driver(hibvt_i2c_driver);
+
+MODULE_AUTHOR("Pan Wen, <wenpan@xxxxxxxxxxxxx>");
+MODULE_DESCRIPTION("HISILICON BVT I2C Bus driver");
+MODULE_LICENSE("GPL v2");
--
2.9.3
--
To unsubscribe from this list: send the line "unsubscribe linux-i2c" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
