On 15 April 2016 at 17:35, Jon Hunter <jonathanh@xxxxxxxxxx> wrote:
> Hi all,
>
> For Tegra we have an i2c device for display port, namely the display
> port auxiliary channel (or dpaux) as specified by the display port
> standard. If an design using Tegra does not utilise the display port
> interface, then the pads assigned to the dpaux can be re-assigned to
> another generic i2c controller (i2c6 for Tegra124/210). In other words,
> the pads can be re-used for a generic i2c interface.
>
> The registers that control whether the pads are mapped to the dpaux or
> i2c6 are located in the dpaux register space. Therefore, I am looking at
> adding pin controller support for dpaux so that i2c6 can request these
> pads if it is enabled and I was hoping to add a pinmux node the to dpaux
> device in device-tree to do this. For example, something like ...
>
> dpaux@0,545c0000 {
> ...
>
> /* pinctrl node */
> pinmux {
> ...
> };
> };
>
> Although the above works, when doing this I noticed that when the device
> booted, I would seeing the following error messages on boot ...
>
> i2c i2c-5: of_i2c: modalias failure on ...
>
> These error messages being caused by the new pinmux node because it is
> not recognised as an i2c device. To avoid this error messages we have
> come up with a couple solutions but wanted to get some feedback on the
> best approach.
Hi,
I'm finding this issue as well on Rockchip SoCs, this is the specific
node that is raising this warning when an adapter is registered with
it:
edp: dp@ff970000 {
compatible = "rockchip,rk3288-dp";
...
ports {
...
};
};
Has there been any agreement since this thread waned?
Thanks,
Tomeu
> 1. Add a i2c-bus sub-node to the dpaux binding (suggested by Stephen
> Warren), so we would have something like the below. Then i2c devices
> for dpaux would be place in the i2c-bus sub-node.
>
> dpaux@0,545c0000 {
> ...
>
> /* pinctrl node */
> pinmux {
> ...
> };
>
> /* place-holder for i2c devices */
> i2c-bus {
> ...
> };
> };
>
> To make the above work ideally we would like to make the 'i2c-bus'
> node a generic solution for all i2c devices, so the i2c core would
> check for the presence of this node and if it is found then would
> default to this node for looking for i2c-devices.
>
> 2. When registering i2c devices via device-tree, the function
> of_i2c_register_devices() checks to see if OF_POPULATED flag is set
> for a given node. If it is set, then the node is skipped. I believe
> this was added for device-tree overlays (commit 4f001fd30145 i2c:
> Mark instantiated device nodes with OF_POPULATE). Another option is
> for the dpaux driver to mark the pinmux node as populated before
> registering the i2c adapter and this will prevent the i2c core from
> trying to parse the pinmux node. I am not sure if this would be
> frowned upon in anyway or if we can guarantee that no future changes
> to DT overlays would change this in a way where it would not work.
>
> Let me know your thoughts.
>
> Cheers
> Jon
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-tegra" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-i2c" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
