[PATCH v3] i2c: designware: Do not require clock when SSCN and FFCN are provided

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



The current driver uses input clock source frequency to calculate
values for [SS|FS]_[HC|LC] registers. However, when booting ACPI, we do not
currently have a good way to provide the frequency information.
Instead, we can leverage the SSCN and FFCN ACPI methods, which can be used
to directly provide these values. So, the clock information should
no longer be required during probing.

However, since clk can be invalid, additional checks must be done where
we are making use of it.

Signed-off-by: Mika Westerberg <mika.westerberg@xxxxxxxxxxxxxxx>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@xxxxxxx>
---
Note: This has been tested on AMD Seattle RevB for both DT and ACPI.

Changes from V2 (https://lkml.org/lkml/2015/12/22/584):
    * Add the i2c_dw_clk_rate from Mika.
    * Add check if get_clk_rate_khz is set before setting sda_hold_time

Changes from V1 (https://lkml.org/lkml/2015/12/15/792):
    In v1, I disregarded the clock if SSCN and FMCN are provided,
    assuming that it was not needed. That was incorrect assumption,
    and is now fixed in v2.

 drivers/i2c/busses/i2c-designware-core.c    | 22 +++++++++++++++-------
 drivers/i2c/busses/i2c-designware-platdrv.c | 24 ++++++++++++------------
 2 files changed, 27 insertions(+), 19 deletions(-)

diff --git a/drivers/i2c/busses/i2c-designware-core.c b/drivers/i2c/busses/i2c-designware-core.c
index 8c48b27..25dccd8 100644
--- a/drivers/i2c/busses/i2c-designware-core.c
+++ b/drivers/i2c/busses/i2c-designware-core.c
@@ -271,6 +271,17 @@ static void __i2c_dw_enable(struct dw_i2c_dev *dev, bool enable)
 		 enable ? "en" : "dis");
 }
 
+static unsigned long i2c_dw_clk_rate(struct dw_i2c_dev *dev)
+{
+	/*
+	 * Clock is not necessary if we got LCNT/HCNT values directly from
+	 * the platform code.
+	 */
+	if (WARN_ON_ONCE(!dev->get_clk_rate_khz))
+		return 0;
+	return dev->get_clk_rate_khz(dev);
+}
+
 /**
  * i2c_dw_init() - initialize the designware i2c master hardware
  * @dev: device private data
@@ -281,7 +292,6 @@ static void __i2c_dw_enable(struct dw_i2c_dev *dev, bool enable)
  */
 int i2c_dw_init(struct dw_i2c_dev *dev)
 {
-	u32 input_clock_khz;
 	u32 hcnt, lcnt;
 	u32 reg;
 	u32 sda_falling_time, scl_falling_time;
@@ -295,8 +305,6 @@ int i2c_dw_init(struct dw_i2c_dev *dev)
 		}
 	}
 
-	input_clock_khz = dev->get_clk_rate_khz(dev);
-
 	reg = dw_readl(dev, DW_IC_COMP_TYPE);
 	if (reg == ___constant_swab32(DW_IC_COMP_TYPE_VALUE)) {
 		/* Configure register endianess access */
@@ -325,12 +333,12 @@ int i2c_dw_init(struct dw_i2c_dev *dev)
 		hcnt = dev->ss_hcnt;
 		lcnt = dev->ss_lcnt;
 	} else {
-		hcnt = i2c_dw_scl_hcnt(input_clock_khz,
+		hcnt = i2c_dw_scl_hcnt(i2c_dw_clk_rate(dev),
 					4000,	/* tHD;STA = tHIGH = 4.0 us */
 					sda_falling_time,
 					0,	/* 0: DW default, 1: Ideal */
 					0);	/* No offset */
-		lcnt = i2c_dw_scl_lcnt(input_clock_khz,
+		lcnt = i2c_dw_scl_lcnt(i2c_dw_clk_rate(dev),
 					4700,	/* tLOW = 4.7 us */
 					scl_falling_time,
 					0);	/* No offset */
@@ -344,12 +352,12 @@ int i2c_dw_init(struct dw_i2c_dev *dev)
 		hcnt = dev->fs_hcnt;
 		lcnt = dev->fs_lcnt;
 	} else {
-		hcnt = i2c_dw_scl_hcnt(input_clock_khz,
+		hcnt = i2c_dw_scl_hcnt(i2c_dw_clk_rate(dev),
 					600,	/* tHD;STA = tHIGH = 0.6 us */
 					sda_falling_time,
 					0,	/* 0: DW default, 1: Ideal */
 					0);	/* No offset */
-		lcnt = i2c_dw_scl_lcnt(input_clock_khz,
+		lcnt = i2c_dw_scl_lcnt(i2c_dw_clk_rate(dev),
 					1300,	/* tLOW = 1.3 us */
 					scl_falling_time,
 					0);	/* No offset */
diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c b/drivers/i2c/busses/i2c-designware-platdrv.c
index 8ffc36b..04edd09 100644
--- a/drivers/i2c/busses/i2c-designware-platdrv.c
+++ b/drivers/i2c/busses/i2c-designware-platdrv.c
@@ -205,16 +205,14 @@ static int dw_i2c_plat_probe(struct platform_device *pdev)
 			DW_IC_CON_RESTART_EN | DW_IC_CON_SPEED_FAST;
 
 	dev->clk = devm_clk_get(&pdev->dev, NULL);
-	dev->get_clk_rate_khz = i2c_dw_get_clk_rate_khz;
-	if (IS_ERR(dev->clk))
-		return PTR_ERR(dev->clk);
-	clk_prepare_enable(dev->clk);
-
-	if (!dev->sda_hold_time && ht) {
-		u32 ic_clk = dev->get_clk_rate_khz(dev);
-
-		dev->sda_hold_time = div_u64((u64)ic_clk * ht + 500000,
-					     1000000);
+	if (!IS_ERR(dev->clk)) {
+		dev->get_clk_rate_khz = i2c_dw_get_clk_rate_khz;
+		clk_prepare_enable(dev->clk);
+
+		if (!dev->sda_hold_time && ht)
+			dev->sda_hold_time = div_u64(
+				(u64)dev->get_clk_rate_khz(dev) * ht + 500000,
+				1000000);
 	}
 
 	if (!dev->tx_fifo_depth) {
@@ -297,7 +295,8 @@ static int dw_i2c_plat_suspend(struct device *dev)
 	struct dw_i2c_dev *i_dev = platform_get_drvdata(pdev);
 
 	i2c_dw_disable(i_dev);
-	clk_disable_unprepare(i_dev->clk);
+	if (!IS_ERR(i_dev->clk))
+		clk_disable_unprepare(i_dev->clk);
 
 	return 0;
 }
@@ -307,7 +306,8 @@ static int dw_i2c_plat_resume(struct device *dev)
 	struct platform_device *pdev = to_platform_device(dev);
 	struct dw_i2c_dev *i_dev = platform_get_drvdata(pdev);
 
-	clk_prepare_enable(i_dev->clk);
+	if (!IS_ERR(i_dev->clk))
+		clk_prepare_enable(i_dev->clk);
 
 	if (!i_dev->pm_runtime_disabled)
 		i2c_dw_init(i_dev);
-- 
2.5.0

--
To unsubscribe from this list: send the line "unsubscribe linux-i2c" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux GPIO]     [Linux SPI]     [Linux Hardward Monitoring]     [LM Sensors]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux