On Sun, 2015-11-01 at 17:32 +0100, Christian Fetzer wrote:
> The SB800 chipset supports a multiplexed main SMBus controller with
> four ports. The multiplexed ports share the same SMBus address and
> register set. The port is selected by bits 2:1 of the smb_en register
> (0x2C).
>
> Only one port can be active at any point in time therefore a mutex is
> needed in order to synchronize access.
>
> Tested on HP ProLiant MicroServer G7 N54L (where this patch adds
> support to access sensor data from the w83795adg).
>
> +static int piix4_add_adapters_sb800(struct pci_dev *dev, unsigned
> short smba)
> +{
> + unsigned short port;
> + int retval;
> + struct i2c_piix4_adapdata *adapdata;
> +
> + for (port = 0; port < PIIX4_MAX_ADAPTERS; port++) {
> + retval = piix4_add_adapter(dev, smba,
> + &piix4_main_adapters[port
> ]);
> + if (retval < 0)
> + goto error;
> +
> + piix4_main_adapters[port]->algo =
> &piix4_smbus_algorithm_sb800;
> +
> + adapdata =
> i2c_get_adapdata(piix4_main_adapters[port]);
> + adapdata->port = port;
> + }
> +
> + return retval;
> +
> +error:
> + dev_err(&dev->dev, "Error setting up SB800 adapters. "
> + "Unregistering all adapters!\n");
This one Mika told already about.
You might use as well
dev_err(&dev->dev,
"…\n")
> + for (port--; port >= 0; port--) {
Isn't look complicated? Like I comment in one of previous patches:
while (--port) {
> + adapdata =
> i2c_get_adapdata(piix4_main_adapters[port]);
> + if (adapdata->smba) {
> + i2c_del_adapter(piix4_main_adapters[port]);
> + kfree(adapdata);
> + kfree(piix4_main_adapters[port]);
> + piix4_main_adapters[port] = NULL;
> + }
> + }
> +
> + return retval;
> +}
> +
> static int piix4_probe(struct pci_dev *dev, const struct
> pci_device_id *id)
> {
> unsigned short smba_idx = 0xcd6;
> @@ -629,19 +714,26 @@ static int piix4_probe(struct pci_dev *dev,
> const struct pci_device_id *id)
>
> /* base address location etc changed in SB800 */
> retval = piix4_setup_sb800(dev, id, 0);
> + if (retval < 0)
> + return retval;
> +
> + /* Try to register multiplexed main SMBus adapter,
> + * give up if we can't */
Block comment
/*
* text1
* text2
*/
> + retval = piix4_add_adapters_sb800(dev, retval);
> } else {
> retval = piix4_setup(dev, id);
> + if (retval < 0)
> + return retval;
> +
> + /* Try to register main SMBus adapter, give up if we
> can't */
> + retval = piix4_add_adapter(dev, retval,
> + &piix4_main_adapters[0]);
> }
>
> /* If no main SMBus found, give up */
> if (retval < 0)
> return retval;
>
> - /* Try to register main SMBus adapter, give up if we can't
> */
> - retval = piix4_add_adapter(dev, retval,
> &piix4_main_adapters[0]);
> - if (retval < 0)
> - return retval;
> -
> /* Check for auxiliary SMBus on some AMD chipsets */
> retval = -ENODEV;
>
--
Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx>
Intel Finland Oy
--
To unsubscribe from this list: send the line "unsubscribe linux-i2c" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
