Am Dienstag, 29. April 2014, 01:34:15 schrieb Max Schwarz: > Driver for the native I2C adapter found in Rockchip RK3xxx SoCs. > > Configuration is only possible through devicetree. The driver is > interrupt driven and supports the I2C_M_IGNORE_NAK mangling bit. > > Tested on the Radxa Rock board, which is based on RK3188. > > Signed-off-by: Max Schwarz <max.schwarz@xxxxxxxxx> > --- > > changes since v1: > - dt property names "rockchip,*" suggested by Heiko Stübner > - fixed overly specific RK3188 comment (Heiko Stübner) > > The dts files needed for testing on Radxa Rock are in my tree on > > https://github.com/xqms/linux.git topic/i2c-rk3x-clean-v2 > > Documentation/devicetree/bindings/i2c/i2c-rk3x.txt | 34 + > drivers/i2c/busses/Kconfig | 10 + > drivers/i2c/busses/Makefile | 1 + > drivers/i2c/busses/i2c-rk3x.c | 731 > +++++++++++++++++++++ 4 files changed, 776 insertions(+) > create mode 100644 Documentation/devicetree/bindings/i2c/i2c-rk3x.txt > create mode 100644 drivers/i2c/busses/i2c-rk3x.c > > diff --git a/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt > b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt new file mode 100644 > index 0000000..19bd386 > --- /dev/null > +++ b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt > @@ -0,0 +1,34 @@ > +* Rockchip RK3xxx I2C controller > + > +This driver interfaces with the native I2C controller present in Rockchip > +RK3xxx SoCs. > + > +Required properties : > + > + - reg : Offset and length of the register set for the device > + - compatible : should be "rockchip,rk3x-i2c" sorry to see it only in the second iteration, but I think the common way for compatibles is to name it after the first device to introduce it (like "rockchip,rk3066-i2c") and newer devices are then simply compatible with it. > + - interrupts : interrupt number > + - clocks : parent clock > + - rockchip,grf : the phandle of the syscon node for the general register > + file (GRF) > + - rockchip,bus-index : index of the bus in the GRF here I only want to make sure, we'll be handling the GRF in general correctly - see other thread about rockchip-pinctrl from some minutes ago. If the whole-grf-as-syscon case wins, the best way to declare the offset would probably be to use the data field of rk3x_i2c_match below and introduce a second "rockchip,rk3188-i2c" compatible for it, for example like the rockchip- pinctrl driver does in its rockchip_pinctrl_dt_match array. Heiko > + > +Optional properties : > + > + - clock-frequency : SCL frequency to use (in Hz). If omitted, 100kHz is > used. + > +Example: > + > +i2c0: i2c@2002d000 { > + compatible = "rockchip,rk3x-i2c"; > + reg = <0x2002d000 0x1000>; > + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + rockchip,grf = <&grf>; > + rockchip,bus-index = <0>; > + > + clock-names = "i2c"; > + clocks = <&cru PCLK_I2C0>; > +}; > diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig > index c94db1c..f973632 100644 > --- a/drivers/i2c/busses/Kconfig > +++ b/drivers/i2c/busses/Kconfig > @@ -663,6 +663,16 @@ config I2C_PXA_SLAVE > is necessary for systems where the PXA may be a target on the > I2C bus. > > +config I2C_RK3X > + tristate "Rockchip RK3xxx I2C adapter" > + depends on OF > + help > + Say Y here to include support for the I2C adapter in Rockchip RK3xxx > + SoCs. > + > + This driver can also be built as a module. If so, the module will > + be called i2c-rk3x. > + > config I2C_QUP > tristate "Qualcomm QUP based I2C controller" > depends on ARCH_QCOM > diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile > index 18d18ff..39b6851 100644 > --- a/drivers/i2c/busses/Makefile > +++ b/drivers/i2c/busses/Makefile > @@ -65,6 +65,7 @@ obj-$(CONFIG_I2C_PNX) += i2c-pnx.o > obj-$(CONFIG_I2C_PUV3) += i2c-puv3.o > obj-$(CONFIG_I2C_PXA) += i2c-pxa.o > obj-$(CONFIG_I2C_PXA_PCI) += i2c-pxa-pci.o > +obj-$(CONFIG_I2C_RK3X) += i2c-rk3x.o > obj-$(CONFIG_I2C_QUP) += i2c-qup.o > obj-$(CONFIG_I2C_RIIC) += i2c-riic.o > obj-$(CONFIG_I2C_S3C2410) += i2c-s3c2410.o > diff --git a/drivers/i2c/busses/i2c-rk3x.c b/drivers/i2c/busses/i2c-rk3x.c > new file mode 100644 > index 0000000..73f1eb7 > --- /dev/null > +++ b/drivers/i2c/busses/i2c-rk3x.c > @@ -0,0 +1,731 @@ > +/* > + * Driver for I2C adapter in Rockchip RK3xxx SoC > + * > + * Max Schwarz <max.schwarz@xxxxxxxxx> > + * based on the patches by Rockchip Inc. > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > + > +#include <linux/kernel.h> > +#include <linux/module.h> > + > +#include <linux/i2c.h> > +#include <linux/time.h> > +#include <linux/interrupt.h> > +#include <linux/delay.h> > +#include <linux/errno.h> > +#include <linux/err.h> > +#include <linux/platform_device.h> > +#include <linux/io.h> > +#include <linux/of_address.h> > +#include <linux/of_irq.h> > +#include <linux/spinlock.h> > +#include <linux/clk.h> > +#include <linux/wait.h> > +#include <linux/mfd/syscon.h> > +#include <linux/regmap.h> > + > + > +/* Register Map */ > +#define REG_CON 0x00 /* control register */ > +#define REG_CLKDIV 0x04 /* clock divisor register */ > +#define REG_MRXADDR 0x08 /* slave address for REGISTER_TX */ > +#define REG_MRXRADDR 0x0c /* slave register address for REGISTER_TX */ > +#define REG_MTXCNT 0x10 /* number of bytes to be transmitted */ > +#define REG_MRXCNT 0x14 /* number of bytes to be received */ > +#define REG_IEN 0x18 /* interrupt enable */ > +#define REG_IPD 0x1c /* interrupt pending */ > +#define REG_FCNT 0x20 /* finished count */ > + > +/* Data buffer offsets */ > +#define TXBUFFER_BASE 0x100 > +#define RXBUFFER_BASE 0x200 > + > +/* REG_CON bits */ > +#define REG_CON_EN (1 << 0) > +enum { > + REG_CON_MOD_TX = 0, /* transmit data */ > + REG_CON_MOD_REGISTER_TX, /* select register and restart */ > + REG_CON_MOD_RX, /* receive data */ > + REG_CON_MOD_REGISTER_RX, /* broken: transmits read addr AND writes > + * register addr */ > +}; > +#define REG_CON_MOD(mod) ((mod) << 1) > +#define REG_CON_MOD_MASK (3 << 1) > +#define REG_CON_START (1 << 3) > +#define REG_CON_STOP (1 << 4) > +#define REG_CON_LASTACK (1 << 5) /* 1: do not send ACK after last receive > */ +#define REG_CON_ACTACK (1 << 6) /* 1: stop if NACK is received */ + > +/* REG_MRXADDR bits */ > +#define REG_MRXADDR_LOW (1 << 24) /* bits [7:0] of MRX[R]ADDR are valid > */ +#define REG_MRXADDR_MID (1 << 25) /* bits [15:8] of MRX[R]ADDR are > valid */ +#define REG_MRXADDR_HIGH (1 << 26) /* bits [23:16] of MRX[R]ADDR > are valid */ + > +/* REG_IEN/REG_IPD bits */ > +#define REG_INT_BTF (1 << 0) /* a byte was transmitted */ > +#define REG_INT_BRF (1 << 1) /* a byte was received */ > +#define REG_INT_MBTF (1 << 2) /* master data transmit finished */ > +#define REG_INT_MBRF (1 << 3) /* master data receive finished */ > +#define REG_INT_START (1 << 4) /* START condition generated */ > +#define REG_INT_STOP (1 << 5) /* STOP condition generated */ > +#define REG_INT_NAKRCV (1 << 6) /* NACK received */ > +#define REG_INT_ALL 0x7f > + > +/* Registers in the GRF (General Register File) */ > +#define GRF_SOC_CON1 4 > + > +/* Constants */ > +#define WAIT_TIMEOUT 200 /* ms */ > + > +enum rk3x_i2c_state { > + STATE_IDLE, > + STATE_START, > + STATE_READ, > + STATE_WRITE, > + STATE_STOP > +}; > + > +struct rk3x_i2c { > + struct i2c_adapter adap; > + struct device *dev; > + > + /* Hardware resources */ > + void __iomem *regs; > + struct regmap *grf; > + unsigned int bus_index; > + struct clk *clk; > + int irq; > + > + /* Settings */ > + unsigned int scl_frequency; > + > + /* Synchronization & notification */ > + spinlock_t lock; > + wait_queue_head_t wait; > + bool busy; > + > + /* Current message */ > + struct i2c_msg *msg; > + u8 addr; > + unsigned int mode; > + > + /* I2C state machine */ > + enum rk3x_i2c_state state; > + unsigned int processed; /* sent/received bytes */ > + int error; > +}; > + > +static inline void i2c_writel(struct rk3x_i2c *i2c, u32 value, > + unsigned int offset) > +{ > + writel(value, i2c->regs + offset); > +} > + > +static inline u32 i2c_readl(struct rk3x_i2c *i2c, unsigned int offset) > +{ > + return readl(i2c->regs + offset); > +} > + > +static inline int rk3x_i2c_set_grf_enable(struct rk3x_i2c *i2c, bool on) > +{ > + u32 con = BIT(27 + i2c->bus_index); /* write mask */ > + > + if (on) > + con |= BIT(11 + i2c->bus_index); > + > + return regmap_write(i2c->grf, GRF_SOC_CON1, con); > +} > + > +/* Reset all interrupt pending bits */ > +static inline void rk3x_i2c_clean_ipd(struct rk3x_i2c *i2c) > +{ > + i2c_writel(i2c, REG_INT_ALL, REG_IPD); > +} > + > +/** > + * Generate a START condition, which triggers a REG_INT_START interrupt. > + */ > +static void rk3x_i2c_start(struct rk3x_i2c *i2c) > +{ > + u32 val; > + > + rk3x_i2c_clean_ipd(i2c); > + i2c_writel(i2c, REG_INT_START, REG_IEN); > + > + /* enable adapter with correct mode, send START condition */ > + val = REG_CON_EN | REG_CON_MOD(i2c->mode) | REG_CON_START; > + > + /* if we want to react to NACK, set ACTACK bit */ > + if (!(i2c->msg->flags & I2C_M_IGNORE_NAK)) > + val |= REG_CON_ACTACK; > + > + i2c_writel(i2c, val, REG_CON); > +} > + > +/** > + * Generate a STOP condition, which triggers a REG_INT_STOP interrupt. > + * > + * @error: Error code to return in rk3x_i2c_xfer > + */ > +static void rk3x_i2c_stop(struct rk3x_i2c *i2c, int error) > +{ > + unsigned int ctrl; > + > + i2c->processed = 0; > + i2c->msg = 0; > + i2c->error = error; > + > + /* Enable stop interrupt */ > + i2c_writel(i2c, REG_INT_STOP, REG_IEN); > + > + i2c->state = STATE_STOP; > + > + ctrl = i2c_readl(i2c, REG_CON); > + ctrl |= REG_CON_STOP; > + i2c_writel(i2c, ctrl, REG_CON); > +} > + > +/** > + * Setup a read according to i2c->msg > + */ > +static void rk3x_i2c_prepare_read(struct rk3x_i2c *i2c) > +{ > + unsigned int len = i2c->msg->len - i2c->processed; > + u32 con; > + > + con = i2c_readl(i2c, REG_CON); > + > + /* the hw can read up to 32 bytes at a time. If we need more than one > + * chunk, send an ACK after the last byte of the current chunk. */ > + if (unlikely(len > 32)) { > + len = 32; > + con &= ~REG_CON_LASTACK; > + } else > + con |= REG_CON_LASTACK; > + > + /* make sure we are in plain RX mode if we read a second chunk */ > + if (i2c->processed != 0) { > + con &= ~REG_CON_MOD_MASK; > + con |= REG_CON_MOD(REG_CON_MOD_RX); > + } > + > + i2c_writel(i2c, con, REG_CON); > + i2c_writel(i2c, len, REG_MRXCNT); > +} > + > +/** > + * Fill the transmit buffer with data from i2c->msg > + */ > +static void rk3x_i2c_fill_transmit_buf(struct rk3x_i2c *i2c) > +{ > + unsigned int i, j; > + u32 cnt = 0; > + u32 val; > + u8 byte; > + > + for (i = 0; i < 8; ++i) { > + val = 0; > + for (j = 0; j < 4; ++j) { > + if (i2c->processed == i2c->msg->len) > + break; > + > + if (i2c->processed == 0 && cnt == 0) > + byte = (i2c->addr & 0x7f) << 1; > + else > + byte = i2c->msg->buf[i2c->processed++]; > + > + val |= byte << (j*8); > + cnt++; > + } > + > + i2c_writel(i2c, val, TXBUFFER_BASE + 4*i); > + > + if (i2c->processed == i2c->msg->len) > + break; > + } > + > + i2c_writel(i2c, cnt, REG_MTXCNT); > +} > + > + > +/* IRQ handlers for individual states */ > + > +static void rk3x_i2c_handle_start(struct rk3x_i2c *i2c, unsigned int ipd) > +{ > + if (!(ipd & REG_INT_START)) { > + rk3x_i2c_stop(i2c, -ENXIO); > + dev_warn(i2c->dev, "unexpected irq in START: 0x%x\n", ipd); > + rk3x_i2c_clean_ipd(i2c); > + return; > + } > + > + /* ack interrupt */ > + i2c_writel(i2c, REG_INT_START, REG_IPD); > + > + /* disable start bit */ > + i2c_writel(i2c, i2c_readl(i2c, REG_CON) & ~REG_CON_START, REG_CON); > + > + /* enable appropriate interrupts and transition */ > + if (i2c->mode == REG_CON_MOD_TX) { > + i2c_writel(i2c, REG_INT_MBTF | REG_INT_NAKRCV, REG_IEN); > + i2c->state = STATE_WRITE; > + rk3x_i2c_fill_transmit_buf(i2c); > + } else { > + /* in any other case, we are going to be reading. */ > + i2c_writel(i2c, REG_INT_MBRF | REG_INT_NAKRCV, REG_IEN); > + i2c->state = STATE_READ; > + rk3x_i2c_prepare_read(i2c); > + } > +} > + > +static void rk3x_i2c_handle_write(struct rk3x_i2c *i2c, unsigned int ipd) > +{ > + if (!(ipd & REG_INT_MBTF)) { > + rk3x_i2c_stop(i2c, -ENXIO); > + dev_err(i2c->dev, "unexpected irq in WRITE: 0x%x\n", ipd); > + rk3x_i2c_clean_ipd(i2c); > + return; > + } > + > + /* ack interrupt */ > + i2c_writel(i2c, REG_INT_MBTF, REG_IPD); > + > + /* are we finished? */ > + if (i2c->processed == i2c->msg->len) > + rk3x_i2c_stop(i2c, i2c->error); > + else > + rk3x_i2c_fill_transmit_buf(i2c); > +} > + > +static void rk3x_i2c_handle_read(struct rk3x_i2c *i2c, unsigned int ipd) > +{ > + unsigned int i; > + unsigned int len = i2c->msg->len - i2c->processed; > + unsigned int val; > + u8 byte; > + > + /* we only care for MBRF here. */ > + if (!(ipd & REG_INT_MBRF)) > + return; > + > + /* ack interrupt */ > + i2c_writel(i2c, REG_INT_MBRF, REG_IPD); > + > + /* read the data from receive buffer */ > + for (i = 0; i < len; ++i) { > + if (i%4 == 0) > + val = i2c_readl(i2c, RXBUFFER_BASE + (i/4)*4); > + > + byte = (val >> ((i%4) * 8)) & 0xff; > + i2c->msg->buf[i2c->processed++] = byte; > + } > + > + /* are we finished? */ > + if (i2c->processed == i2c->msg->len) > + rk3x_i2c_stop(i2c, i2c->error); > + else > + rk3x_i2c_prepare_read(i2c); > +} > + > +static void rk3x_i2c_handle_stop(struct rk3x_i2c *i2c, unsigned int ipd) > +{ > + unsigned int con; > + > + if (!(ipd & REG_INT_STOP)) { > + rk3x_i2c_stop(i2c, -ENXIO); > + dev_err(i2c->dev, "unexpected irq in STOP: 0x%x\n", ipd); > + rk3x_i2c_clean_ipd(i2c); > + return; > + } > + > + /* ack interrupt */ > + i2c_writel(i2c, REG_INT_STOP, REG_IPD); > + > + /* disable STOP bit */ > + con = i2c_readl(i2c, REG_CON); > + con &= ~REG_CON_STOP; > + i2c_writel(i2c, con, REG_CON); > + > + i2c->busy = 0; > + i2c->state = STATE_IDLE; > + > + /* signal rk3x_i2c_xfer that we are finished */ > + wake_up(&i2c->wait); > +} > + > +static irqreturn_t rk3x_i2c_irq(int irqno, void *dev_id) > +{ > + struct rk3x_i2c *i2c = dev_id; > + unsigned int ipd; > + > + spin_lock(&i2c->lock); > + > + ipd = i2c_readl(i2c, REG_IPD); > + if (i2c->state == STATE_IDLE) { > + dev_warn(i2c->dev, "irq in STATE_IDLE, ipd = 0x%x\n", ipd); > + rk3x_i2c_clean_ipd(i2c); > + goto out; > + } > + > + dev_dbg(i2c->dev, "IRQ: state %d, ipd: %x\n", i2c->state, ipd); > + > + /* Clean interrupt bits we don't care about */ > + ipd &= ~(REG_INT_BRF | REG_INT_BTF); > + > + if (ipd & REG_INT_NAKRCV) { > + /* We got a NACK in the last operation. Depending on whether > + * IGNORE_NAK is set, we have to stop the operation and report > + * an error. */ > + i2c_writel(i2c, REG_INT_NAKRCV, REG_IPD); > + > + ipd &= ~REG_INT_NAKRCV; > + > + if (!(i2c->msg->flags & I2C_M_IGNORE_NAK)) > + rk3x_i2c_stop(i2c, -EAGAIN); > + } > + > + /* is there anything left to handle? */ > + if (unlikely(ipd == 0)) > + goto out; > + > + switch (i2c->state) { > + case STATE_START: > + rk3x_i2c_handle_start(i2c, ipd); > + break; > + case STATE_WRITE: > + rk3x_i2c_handle_write(i2c, ipd); > + break; > + case STATE_READ: > + rk3x_i2c_handle_read(i2c, ipd); > + break; > + case STATE_STOP: > + rk3x_i2c_handle_stop(i2c, ipd); > + break; > + case STATE_IDLE: > + break; > + } > + > +out: > + spin_unlock(&i2c->lock); > + return IRQ_HANDLED; > +} > + > +static void rk3x_i2c_set_scl_rate(struct rk3x_i2c *i2c, unsigned long > scl_rate) +{ > + unsigned long i2c_rate = clk_get_rate(i2c->clk); > + unsigned int div; > + > + /* SCL rate = (clk rate) / (8 * DIV) */ > + div = DIV_ROUND_UP(i2c_rate, scl_rate * 8); > + > + /* The lower and upper half of the CLKDIV reg describe the length of > + * SCL low & high periods. */ > + div = DIV_ROUND_UP(div, 2); > + > + i2c_writel(i2c, (div << 16) | (div & 0xffff), REG_CLKDIV); > +} > + > +/** > + * Setup I2C registers for an I2C operation specified by msgs, num. > + * > + * Must be called with i2c->lock held. > + * > + * @msgs: I2C msgs to process > + * @num: Number of msgs > + * > + * returns: Number of I2C msgs processed or negative in case of error > + */ > +static int rk3x_i2c_setup(struct rk3x_i2c *i2c, struct i2c_msg *msgs, int > num) +{ > + u32 addr = (msgs[0].addr & 0x7f) << 1; > + int ret = 0; > + > + /* > + * The I2C adapter can issue a small (len < 4) write packet before > + * reading. This speeds up SMBus-style register reads. > + * The MRXADDR/MRXRADDR hold the slave address and the slave register > + * address in this case. > + */ > + > + if (num >= 2 && msgs[0].len < 4 > + && !(msgs[0].flags & I2C_M_RD) > + && (msgs[1].flags & I2C_M_RD)) { > + u32 reg_addr = 0; > + > + dev_dbg(i2c->dev, "Combined write/read from addr 0x%x\n", > + addr >> 1); > + > + if (msgs[0].len == 0) > + return -EINVAL; > + > + /* Fill MRXRADDR with the register address(es) */ > + reg_addr = msgs[0].buf[0]; > + reg_addr |= REG_MRXADDR_LOW; > + > + if (msgs[0].len >= 2) { > + reg_addr |= msgs[0].buf[1] << 8; > + reg_addr |= REG_MRXADDR_MID; > + > + if (msgs[0].len >= 3) { > + reg_addr |= msgs[0].buf[2] << 16; > + reg_addr |= REG_MRXADDR_HIGH; > + } > + } > + > + /* msgs[0] is handled by hw. */ > + i2c->msg = &msgs[1]; > + > + i2c->mode = REG_CON_MOD_REGISTER_TX; > + > + i2c_writel(i2c, addr | REG_MRXADDR_LOW, REG_MRXADDR); > + i2c_writel(i2c, reg_addr, REG_MRXRADDR); > + > + ret = 2; > + } else { > + /* We'll have to do it the boring way and process the msgs > + * one-by-one. */ > + > + if (msgs[0].flags & I2C_M_RD) { > + addr |= 1; /* set read bit */ > + > + /* We have to transmit the slave addr first. Use > + * MOD_REGISTER_TX for that purpose. */ > + i2c->mode = REG_CON_MOD_REGISTER_TX; > + i2c_writel(i2c, addr | REG_MRXADDR_LOW, REG_MRXADDR); > + i2c_writel(i2c, 0, REG_MRXRADDR); > + } else { > + i2c->mode = REG_CON_MOD_TX; > + } > + > + i2c->msg = &msgs[0]; > + > + ret = 1; > + } > + > + i2c->addr = msgs[0].addr; > + i2c->busy = true; > + i2c->state = STATE_START; > + i2c->processed = 0; > + i2c->error = 0; > + > + rk3x_i2c_clean_ipd(i2c); > + > + return ret; > +} > + > +static int rk3x_i2c_xfer(struct i2c_adapter *adap, > + struct i2c_msg *msgs, int num) > +{ > + struct rk3x_i2c *i2c = (struct rk3x_i2c *)adap->algo_data; > + unsigned long timeout, flags; > + int ret = 0; > + int i; > + > + spin_lock_irqsave(&i2c->lock, flags); > + > + clk_enable(i2c->clk); > + > + /* The clock rate might have changed, so setup the divider again */ > + rk3x_i2c_set_scl_rate(i2c, i2c->scl_frequency); > + > + /* Process msgs. We can handle more than one message at once (see > + * rk3x_i2c_setup()). */ > + for (i = 0; i < num; i += ret) { > + ret = rk3x_i2c_setup(i2c, msgs + i, num); > + > + if (ret < 0) { > + dev_err(i2c->dev, "rk3x_i2c_setup() failed\n"); > + break; > + } > + > + spin_unlock_irqrestore(&i2c->lock, flags); > + > + rk3x_i2c_start(i2c); > + > + timeout = wait_event_timeout(i2c->wait, !i2c->busy, > + msecs_to_jiffies(WAIT_TIMEOUT)); > + > + spin_lock_irqsave(&i2c->lock, flags); > + > + if (timeout == 0) { > + dev_err(i2c->dev, "timeout, ipd: 0x%08X", > + i2c_readl(i2c, REG_IPD)); > + > + /* Force a STOP condition without interrupt */ > + i2c_writel(i2c, 0, REG_IEN); > + i2c_writel(i2c, REG_CON_EN | REG_CON_STOP, REG_CON); > + > + i2c->state = STATE_IDLE; > + > + ret = -ETIMEDOUT; > + break; > + } > + > + if (i2c->error) { > + ret = i2c->error; > + break; > + } > + } > + > + clk_disable(i2c->clk); > + spin_unlock_irqrestore(&i2c->lock, flags); > + > + return ret; > +} > + > +static u32 rk3x_i2c_func(struct i2c_adapter *adap) > +{ > + return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_PROTOCOL_MANGLING; > +} > + > +static const struct i2c_algorithm rk3x_i2c_algorithm = { > + .master_xfer = rk3x_i2c_xfer, > + .functionality = rk3x_i2c_func, > +}; > + > +static int rk3x_i2c_probe(struct platform_device *pdev) > +{ > + struct device_node *np = pdev->dev.of_node; > + struct rk3x_i2c *i2c; > + struct resource *mem; > + int ret = 0; > + > + if (!pdev->dev.of_node) { > + dev_err(&pdev->dev, "rk3x-i2c needs a devicetree node\n"); > + return -EINVAL; > + } > + > + i2c = devm_kzalloc(&pdev->dev, sizeof(struct rk3x_i2c), GFP_KERNEL); > + if (!i2c) { > + dev_err(&pdev->dev, "Could not alloc driver memory\n"); > + return -ENOMEM; > + } > + > + if (of_property_read_u32(pdev->dev.of_node, "rockchip,bus-index", > + &i2c->bus_index)) { > + dev_err(&pdev->dev, > + "rk3x-i2c requires 'rockchip,bus-index' property\n"); > + return -EINVAL; > + } > + > + if (of_property_read_u32(pdev->dev.of_node, "clock-frequency", > + &i2c->scl_frequency)) { > + i2c->scl_frequency = 100 * 1000; > + dev_info(&pdev->dev, "using default SCL frequency: 100kHz\n"); > + } > + > + strlcpy(i2c->adap.name, "rk3x-i2c", sizeof(i2c->adap.name)); > + i2c->adap.owner = THIS_MODULE; > + i2c->adap.algo = &rk3x_i2c_algorithm; > + i2c->adap.retries = 3; > + i2c->adap.dev.of_node = np; > + i2c->adap.algo_data = i2c; > + i2c->adap.dev.parent = &pdev->dev; > + > + i2c->dev = &pdev->dev; > + > + spin_lock_init(&i2c->lock); > + init_waitqueue_head(&i2c->wait); > + > + i2c->clk = devm_clk_get(&pdev->dev, 0); > + if (IS_ERR(i2c->clk)) { > + dev_err(&pdev->dev, "cannot get clock\n"); > + return -ENOENT; > + } > + > + clk_prepare_enable(i2c->clk); > + > + mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); > + i2c->regs = devm_ioremap_resource(&pdev->dev, mem); > + if (IS_ERR(i2c->regs)) { > + ret = PTR_ERR(i2c->regs); > + goto err_clk; > + } > + > + /* Enable the I2C bus in the SOC general register file */ > + i2c->grf = syscon_regmap_lookup_by_phandle(np, "rockchip,grf"); > + if (IS_ERR(i2c->grf)) { > + dev_err(&pdev->dev, > + "rk3x-i2c requires a 'rockchip,grf' property\n"); > + ret = PTR_ERR(i2c->grf); > + goto err_clk; > + } > + > + ret = rk3x_i2c_set_grf_enable(i2c, true); > + if (ret != 0) { > + dev_err(&pdev->dev, "could not enable I2C adapter in GRF: %d\n", > + ret); > + ret = -EIO; > + goto err_clk; > + } > + > + /* IRQ setup */ > + i2c->irq = ret = platform_get_irq(pdev, 0); > + if (ret <= 0) { > + dev_err(&pdev->dev, "cannot find rk3x IRQ\n"); > + ret = -EINVAL; > + goto err_grf; > + } > + > + ret = devm_request_irq(&pdev->dev, i2c->irq, rk3x_i2c_irq, > + 0, dev_name(&pdev->dev), i2c); > + if (ret != 0) { > + dev_err(&pdev->dev, "cannot request IRQ\n"); > + goto err_grf; > + } > + > + platform_set_drvdata(pdev, i2c); > + > + if (i2c_add_adapter(&i2c->adap) != 0) { > + pr_err("rk3x-i2c: Could not register adapter\n"); > + goto err_grf; > + } > + > + dev_info(&pdev->dev, "Initialized RK3xxx I2C bus at 0x%08x\n", > + (unsigned int)i2c->regs); > + > + clk_disable(i2c->clk); > + return 0; > + > +err_grf: > + rk3x_i2c_set_grf_enable(i2c, false); > +err_clk: > + clk_disable_unprepare(i2c->clk); > + return ret; > +} > + > +static int rk3x_i2c_remove(struct platform_device *pdev) > +{ > + struct rk3x_i2c *i2c = platform_get_drvdata(pdev); > + > + rk3x_i2c_set_grf_enable(i2c, false); > + > + clk_unprepare(i2c->clk); > + i2c_del_adapter(&i2c->adap); > + > + return 0; > +} > + > +static const struct of_device_id rk3x_i2c_match[] = { > + { .compatible = "rockchip,rk3x-i2c" }, > +}; > + > +static struct platform_driver rk3x_i2c_driver = { > + .probe = rk3x_i2c_probe, > + .remove = rk3x_i2c_remove, > + .driver = { > + .owner = THIS_MODULE, > + .name = "rk3x-i2c", > + .of_match_table = rk3x_i2c_match, > + }, > +}; > + > +module_platform_driver(rk3x_i2c_driver); > + > +MODULE_DESCRIPTION("Rockchip RK3xxx I2C Bus driver"); > +MODULE_AUTHOR("Max Schwarz <max.schwarz@xxxxxxxxx>"); > +MODULE_LICENSE("GPL v2"); -- To unsubscribe from this list: send the line "unsubscribe linux-i2c" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
