Hi,
On Mon, Nov 19, 2012 at 02:30:26PM +0530, Abhilash Kesavan wrote:
> The I2C driver makes a gpio_request during initialization. This request
> happens again on resume and fails due to the earlier successful request.
> Re-factor the code to only initialize the gpios during probe.
>
> Errors on resume without this:
> [ 16.020000] s3c-i2c s3c2440-i2c.0: gpio [42] request failed
> [ 16.020000] s3c-i2c s3c2440-i2c.1: gpio [44] request failed
> [ 16.020000] s3c-i2c s3c2440-i2c.2: gpio [6] request failed
>
> Signed-off-by: Abhilash Kesavan <a.kesavan@xxxxxxxxxxx>
> ---
> Changes from v1:
> Refactor code to initialize gpios only during probe
>
> drivers/i2c/busses/i2c-s3c2410.c | 26 +++++++++++++++++++-------
> 1 files changed, 19 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-s3c2410.c b/drivers/i2c/busses/i2c-s3c2410.c
> index 081e261..0ca321b 100644
> --- a/drivers/i2c/busses/i2c-s3c2410.c
> +++ b/drivers/i2c/busses/i2c-s3c2410.c
> @@ -856,6 +856,7 @@ static int s3c24xx_i2c_parse_dt_gpio(struct s3c24xx_i2c *i2c)
> dev_err(i2c->dev, "invalid gpio[%d]: %d\n", idx, gpio);
> goto free_gpio;
> }
> + i2c->gpios[idx] = gpio;
Without this line, gpios won't be freed at all, right? This should be a
separate patch then, since it fixes a seperate issue.
>
> ret = gpio_request(gpio, "i2c-bus");
> if (ret) {
> @@ -892,6 +893,18 @@ static void s3c24xx_i2c_dt_gpio_free(struct s3c24xx_i2c *i2c)
> }
> #endif
>
> +static int s3c24xx_i2c_cfg_gpio(struct s3c24xx_i2c *i2c)
> +{
> + struct s3c2410_platform_i2c *pdata = i2c->pdata;
> +
> + if (pdata->cfg_gpio)
> + pdata->cfg_gpio(to_platform_device(i2c->dev));
> + else if (IS_ERR(i2c->pctrl) && s3c24xx_i2c_parse_dt_gpio(i2c))
> + return -EINVAL;
> +
> + return 0;
> +}
> +
> /* s3c24xx_i2c_init
> *
> * initialise the controller, set the IO lines and frequency
> @@ -907,13 +920,6 @@ static int s3c24xx_i2c_init(struct s3c24xx_i2c *i2c)
>
> pdata = i2c->pdata;
>
> - /* inititalise the gpio */
> -
> - if (pdata->cfg_gpio)
> - pdata->cfg_gpio(to_platform_device(i2c->dev));
> - else if (IS_ERR(i2c->pctrl) && s3c24xx_i2c_parse_dt_gpio(i2c))
> - return -EINVAL;
> -
> /* write slave address */
>
> writeb(pdata->slave_addr, i2c->regs + S3C2410_IICADD);
> @@ -1054,6 +1060,12 @@ static int s3c24xx_i2c_probe(struct platform_device *pdev)
>
> i2c->pctrl = devm_pinctrl_get_select_default(i2c->dev);
>
> + /* inititalise the i2c gpio lines */
> +
> + ret = s3c24xx_i2c_cfg_gpio(i2c);
> + if (ret != 0)
> + goto err_clk;
> +
I don't think the seperate function is needed here, just copy the code block?
Thanks,
Wolfram
--
Pengutronix e.K. | Wolfram Sang |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Attachment:
signature.asc
Description: Digital signature
