Hi Corentin,
On Wed, 06 Jul 2011 13:53:36 +0200, corentin.labbe wrote:
> hello
>
> I have a sun blade 100 and I want to get the sensors working with
> lm_sensors, but in current state, it doesn't work.
>
> After some research, I have found that all SMBUS driver and the i2c_ali1535 particularly can't work.
> It assumes that ioport address are 16bits wide (address stored with an unsigned short).
> But on SPARC arch, ioports are mapped in memory and so are stored with an unsigned long.
>
> So I write this patch for i2c_ali1535 for supporting SPARC architecture.
> With this patch, the driver i2c_ali1535 loads and works successfully.
> # sensors
> adm1023-i2c-0-18
> Adapter: SMBus ALI1535 adapter at 0x1fe02000620
> temp1: +31.0 C (low = -55.0 C, high = +127.0 C)
> temp2: +61.6 C (low = -55.0 C, high = +127.0 C)
>
> I sent this patch for review at sparclinux@xxxxxxxxxxxxxxx and one person confirm me that it works on his sun-blade 100.
>
> Bests regards,
>
> Signed-off-by: LABBE Corentin <corentin.labbe@xxxxxxxxxxx>
Overall I like the patch. Minor comments below:
> ---
> --- linux/drivers/i2c/busses/i2c-ali1535.c.orig 2011-06-15 18:02:56.000000000 +0200
> +++ linux/drivers/i2c/busses/i2c-ali1535.c 2011-06-15 18:05:26.000000000 +0200
> @@ -132,7 +132,7 @@
> #define ALI1535_SMBIO_EN 0x04 /* SMB I/O Space enable */
>
> static struct pci_driver ali1535_driver;
> -static unsigned short ali1535_smba;
> +static unsigned long ali1535_smba;
>
> /* Detect whether a ALI1535 can be found, and initialize it, where necessary.
> Note the differences between kernels with the old PCI BIOS interface and
> @@ -142,6 +142,7 @@ static int __devinit ali1535_setup(struc
> {
> int retval = -ENODEV;
> unsigned char temp;
> + unsigned short offset;
>
> /* Check the following things:
> - SMB I/O address is initialized
> @@ -149,15 +150,27 @@ static int __devinit ali1535_setup(struc
> - We can use the addresses
> */
>
> + if (pci_enable_device(dev)) {
> + dev_err(&dev->dev, "ALI1535_smb cant enable device");
cant -> can't, and missing trailing \n.
> + goto exit;
> + }
Please return the error code from pci_enable_device() instead of
crafting your own.
> +
> /* Determine the address of the SMBus area */
> - pci_read_config_word(dev, SMBBA, &ali1535_smba);
> - ali1535_smba &= (0xffff & ~(ALI1535_SMB_IOSIZE - 1));
> - if (ali1535_smba == 0) {
> + pci_read_config_word(dev, SMBBA, &offset);
> + dev_dbg(&dev->dev, "ALI1535_smb is at offset 0x%04x", offset);
Missing trailing \n.
> + offset &= (0xffff & ~(ALI1535_SMB_IOSIZE - 1));
> + if (offset == 0) {
> dev_warn(&dev->dev,
> "ALI1535_smb region uninitialized - upgrade BIOS?\n");
> goto exit;
> }
>
> + ali1535_smba = pci_resource_start(dev, 0) + offset;
> + if ((pci_resource_flags(dev, 0) & IORESOURCE_IO) == 0) {
> + dev_err(&dev->dev, "ALI1535_smb bar 0 is not IORESOURCE_IO");
Missing trailing \n.
> + goto exit;
> + }
You should swap these: first check the resource type, and if it is
correct, call pci_resource_start(). I agree it makes no difference in
practice, but it is cleaner.
> +
> retval = acpi_check_region(ali1535_smba, ALI1535_SMB_IOSIZE,
> ali1535_driver.name);
> if (retval)
> @@ -165,7 +178,7 @@ static int __devinit ali1535_setup(struc
>
> if (!request_region(ali1535_smba, ALI1535_SMB_IOSIZE,
> ali1535_driver.name)) {
> - dev_err(&dev->dev, "ALI1535_smb region 0x%x already in use!\n",
> + dev_err(&dev->dev, "ALI1535_smb region 0x%lx already in use!\n",
> ali1535_smba);
> goto exit;
> }
> @@ -196,7 +209,7 @@ static int __devinit ali1535_setup(struc
> */
> pci_read_config_byte(dev, SMBREV, &temp);
> dev_dbg(&dev->dev, "SMBREV = 0x%X\n", temp);
> - dev_dbg(&dev->dev, "ALI1535_smba = 0x%X\n", ali1535_smba);
> + dev_dbg(&dev->dev, "ALI1535_smba = 0x%0lx\n", ali1535_smba);
Prefix "0" alone is meaningless.
>
> retval = 0;
> exit:
> @@ -499,7 +512,7 @@ static int __devinit ali1535_probe(struc
> ali1535_adapter.dev.parent = &dev->dev;
>
> snprintf(ali1535_adapter.name, sizeof(ali1535_adapter.name),
> - "SMBus ALI1535 adapter at %04x", ali1535_smba);
> + "SMBus ALI1535 adapter at %0lx", ali1535_smba);
This would potentially change the string on other systems. The adapter
name can be used as a unique identifier in sensors.conf or i2c tools
command line, so changing it is bad. Please keep the "04" as is, it
won't change anything for large ali1535_smba values.
> return i2c_add_adapter(&ali1535_adapter);
> }
Please adjust these small mistakes, resend, and I'll be happy to take
your patch in kernel 3.2.
--
Jean Delvare
--
To unsubscribe from this list: send the line "unsubscribe linux-i2c" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
