>> The board is built around the Poulsbo and therefore using the 'i2c-isch' >> driver. > > Check for error messages when you load the i2c-isch driver. Note that > in kernel 2.6.34 the structure of the i2c-isch driver was changed, from > a standalone PCI driver to a MFD driver. Please make sure that you have > CONFIG_LPC_SCH installed and driver lpc_sch loaded, otherwise i2c-isch > will never see the platform device it is looking for. Thanks for the suggestion, unfortunately there is an issue with lpc_sch loading, and error is reported via dmesg. -- [ 403.809826] ACPI: resource (null) [io 0x0480-0x04bf] conflicts with ACPI region PHO_ [io 0x4bc-0x4bc] [ 403.809834] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 403.809921] lpc_sch: probe of 0000:00:1f.0 failed with error -16 -- 34 rmmod i2c_isch 35 rmmod lpc_sch 36 rmmod i2c_gpio 37 tree /sys/bus/i2c/ 38 modprobe i2c_isch 39 modprobe i2c_gpio 40 modprobe lpc_sch 41 dmesg | tail -- Any further suggestions would be much appreciated. The system reports the poulsbo under 'lspci' as: -- 00:1b.0 Audio device: Intel Corporation System Controller Hub (SCH Poulsbo) HD Audio Controller (rev 07) Subsystem: Intel Corporation Device 8119 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at dff5c000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM L0s Enabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01 Status: NegoPending- InProgress- VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable- ID=0 ArbSelect=Fixed TC/VC=00 Status: NegoPending- InProgress- Capabilities: [130 v1] Root Complex Link Desc: PortNumber=0f ComponentID=00 EltType=Config Link0: Desc: TargetPort=00 TargetComponent=00 AssocRCRB- LinkType=MemMapped LinkValid+ Addr: 00000000f0000000 Kernel driver in use: HDA Intel 00:1c.0 PCI bridge: Intel Corporation System Controller Hub (SCH Poulsbo) PCI Express Port 1 (rev 07) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00001000-00001fff Memory behind bridge: cfd00000-cfdfffff Prefetchable memory behind bridge: 80000000-801fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us ClockPM+ Surprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Slot #0, PowerLimit 0.000W; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [90] Subsystem: Intel Corporation Device 8119 Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pcieport 00:1d.0 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #1 (rev 07) (prog-if 00 [UHCI]) Subsystem: Intel Corporation Device 8119 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 20 Region 4: I/O ports at e480 [size=32] Kernel driver in use: uhci_hcd 00:1d.1 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #2 (rev 07) (prog-if 00 [UHCI]) Subsystem: Intel Corporation Device 8119 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 21 Region 4: I/O ports at e080 [size=32] Kernel driver in use: uhci_hcd 00:1d.2 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #3 (rev 07) (prog-if 00 [UHCI]) Subsystem: Intel Corporation Device 8119 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 22 Region 4: I/O ports at ef00 [size=32] Kernel driver in use: uhci_hcd 00:1d.7 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB EHCI #1 (rev 07) (prog-if 20 [EHCI]) Subsystem: Intel Corporation Device 8119 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 23 Region 0: Memory at dff5bc00 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Debug port: BAR=1 offset=00a0 Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge: Intel Corporation System Controller Hub (SCH Poulsbo) LPC Bridge (rev 07) Subsystem: Intel Corporation System Controller Hub (SCH Poulsbo) LPC Bridge Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:1f.1 IDE interface: Intel Corporation System Controller Hub (SCH Poulsbo) IDE Controller (rev 07) (prog-if 80 [Master]) Subsystem: Intel Corporation Device 8119 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] Region 4: I/O ports at ffa0 [size=16] Kernel driver in use: pata_sch -- >> Reviewing the schematic I see that there are several buses, each going >> to >> individual components: >> IT8516 U5/110+111 -> LTC1760 U6/18+22 [battery charger â?? 0x1A/0x12] >> IT8516 U5/115+116 -> W83L771 U60/8+7 [thermal sensor â?? 0x18??] >> IT8516 U5/117+118 -> LSM303DLH U64/19+20 [accel/compass â?? 0x19] >> POULSBO U2/G37+H38 -> PCI Express Socket > > This suggests that the board uses the SMBus controllers in the ITE IT8516 > Super-I/O chip rather than the Intel SCH south bridge. Unfortunately we > have no support for the SMBus controllers of the IT8516, and I doubt we > get support anytime soon as I was unable to find a datasheet for the > ITE IT8516. > I believe that Jean is correct, we have exchanged a few emails regarding the IT8516 SuperIO chip and have some ideas about getting some support. Simon. -- To unsubscribe from this list: send the line "unsubscribe linux-i2c" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
