Re: vmemmap alloc failure in hot_add_req()

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Michael,

On 6/17/2021 5:16 PM, Michael Kelley wrote:
From: David Hildenbrand <david@xxxxxxxxxx> Sent: Thursday, June 17, 2021 1:43 AM

It does look like this kernel configuration has
CONFIG_MEMORY_HOTPLUG_DEFAULT_ONLINE=y.

Okay, so then it's most likely really more of an issue with fragmented
physical memory -- which is suboptimal but not a show blocker in your setup.

(there are still cases where memory onlining can fail, especially with
kasan running, but these are rather corner cases)


If it's not getting onlined, you easily sport after hotplug e.g., via
"lsmem" that there are quite some offline memory blocks.

Note that x86_64 code will fallback from populating huge pages to
populating base pages for the vmemmap; this can happen easily when under
memory pressure.

Not sure if it is relevant or not but this warning can show up within a
minute of startup without me doing anything in particular.

I remember that Hyper-V will start with a certain (configured) boot VM
memory size and once the guest is up and running, use memory stats of
the guest to decide whether to add (hotplug) or remove (balloon inflate)
memory from the VM.

So this could just be Hyper-V trying to apply its heuristics.

Nathan --

Could you clarify if your VM is running in the context of the Windows
Subsystem for Linux (WSL) v2 feature in Windows 10?  Or are you
running a "traditional" VM created using the Hyper-V Manager UI
or Powershell?

This is a traditional VM created using the Hyper-V Manager.

If the latter, how do you have the memory configuration set up?  In
the UI, first you can specify the RAM allocated to the VM.  Then
separately, you can enable the "Dynamic Memory" feature, in which
case you also specify a "Minimum RAM" and "Maximum RAM".  It
looks like you must have the "Dynamic Memory" feature enabled
since the original stack trace includes the hot_add_req() function
from the hv_balloon driver.

That is correct. I believe Dynamic Memory is the default setting so I just left that as it was. The startup memory for this virtual machine is 2GB as it is a lightweight Arch Linux Xfce4 configuration and aside from occasionally compiling software, it will just be sitting there because it is mainly there for testing kernels.

The Dynamic Memory feature is generally used only when you
need to allow Hyper-V to manage the allocation of physical memory
across multiple VMs.  Dynamic Memory is essentially Hyper-V's way of
allowing memory overcommit.  If you don't need that capability,
turning off Dynamic Memory and just specifying the amount of
memory you want to assign to the VM is the best course of action.

Ack. My workstation was occasionally memory constrained so I figured relying on the Dynamic Memory feature would make sense. I upgraded the amount of RAM that I had today so I will probably just end up disabling the Dynamic Memory feature and allocating the amount of memory up front.

With Dynamic Memory enabled, you may have encountered a
situation where the memory needs of the VM grew very quickly,
and Hyper-V balloon driver got into a situation where it needed
to allocate memory in order to add memory, and it couldn't.  If
you want to continue to use the Dynamic Memory feature, then
you probably need to increase the initial amount of RAM assigned
to the VM (the "RAM" setting in the Hyper-V Manager UI).

I will keep that in mind and see if I can find a good number.

Thanks for the reply!

Cheers,
Nathan



[Index of Archives]     [Linux Samsung SoC]     [Linux Rockchip SoC]     [Linux Actions SoC]     [Linux for Synopsys ARC Processors]     [Linux NFS]     [Linux NILFS]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]


  Powered by Linux