Re: [PATCH 2/3] hwmon: (pmbus/core) add POWER_GOOD signal limits support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue 10 Sep 2024 at 07:37, Guenter Roeck <linux@xxxxxxxxxxxx> wrote:

> On 9/9/24 23:43, Jerome Brunet wrote:
>> On Mon 09 Sep 2024 at 11:16, Guenter Roeck <linux@xxxxxxxxxxxx> wrote:
>> 
>>> On 9/9/24 08:39, Jerome Brunet wrote:
>>>> Add support for POWER_GOOD_ON and POWER_GOOD_OFF standard PMBus commands.
>>>> For PMBus devices that offer a POWER_GOOD signal, these commands are used
>>>> for setting the output voltage at which a power good signal should be
>>>> asserted and negated.
>>>> Power Good signals are device and manufacturer specific. Many factors
>>>> other
>>>> than output voltage may be used to determine whether or not the POWER_GOOD
>>>> signal is to be asserted. PMBus device users are instructed to consult the
>>>> device manufacturer’s product literature for the specifics of the device
>>>> they are using.
>>>> Note that depending on the choice of the device manufacturer that a
>>>> device
>>>> may drive a POWER_GOOD signal high or low to indicate that the signal is
>>>> asserted.
>>>> Signed-off-by: Jerome Brunet <jbrunet@xxxxxxxxxxxx>
>>>> ---
>>>>    drivers/hwmon/pmbus/pmbus.h      | 3 +++
>>>>    drivers/hwmon/pmbus/pmbus_core.c | 6 ++++++
>>>>    2 files changed, 9 insertions(+)
>>>> diff --git a/drivers/hwmon/pmbus/pmbus.h b/drivers/hwmon/pmbus/pmbus.h
>>>> index 5d5dc774187b..e322d2dd9fb7 100644
>>>> --- a/drivers/hwmon/pmbus/pmbus.h
>>>> +++ b/drivers/hwmon/pmbus/pmbus.h
>>>> @@ -78,6 +78,9 @@ enum pmbus_regs {
>>>>    	PMBUS_IIN_OC_FAULT_LIMIT	= 0x5B,
>>>>    	PMBUS_IIN_OC_WARN_LIMIT		= 0x5D,
>>>>    +	PMBUS_POWER_GOOD_ON		= 0x5E,
>>>> +	PMBUS_POWER_GOOD_OFF		= 0x5F,
>>>> +
>>>>    	PMBUS_POUT_OP_FAULT_LIMIT	= 0x68,
>>>>    	PMBUS_POUT_OP_WARN_LIMIT	= 0x6A,
>>>>    	PMBUS_PIN_OP_WARN_LIMIT		= 0x6B,
>>>> diff --git a/drivers/hwmon/pmbus/pmbus_core.c b/drivers/hwmon/pmbus/pmbus_core.c
>>>> index 0ea6fe7eb17c..94ddf0166770 100644
>>>> --- a/drivers/hwmon/pmbus/pmbus_core.c
>>>> +++ b/drivers/hwmon/pmbus/pmbus_core.c
>>>> @@ -1768,6 +1768,12 @@ static const struct pmbus_limit_attr vout_limit_attrs[] = {
>>>>    		.attr = "crit",
>>>>    		.alarm = "crit_alarm",
>>>>    		.sbit = PB_VOLTAGE_OV_FAULT,
>>>> +	}, {
>>>> +		.reg = PMBUS_POWER_GOOD_ON,
>>>> +		.attr = "good_on",
>>>> +	}, {
>>>> +		.reg = PMBUS_POWER_GOOD_OFF,
>>>> +		.attr = "good_off",
>>>>    	}, {
>>>>    		.reg = PMBUS_VIRT_READ_VOUT_AVG,
>>>>    		.update = true,
>>>>
>>>
>>> Those attributes are not hardware monitoring attributes and therefore not
>>> acceptable. In general I am not sure if they should be configurable in the
>>> first place, but definitely not from the hardware monitoring subsystem.
>>> Maybe the regulator subsystem callbacks set_over_voltage_protection and
>>> set_under_voltage_protection would be appropriate (with severity
>>> REGULATOR_SEVERITY_PROT), but that should be discussed with regulator
>>> subsystem maintainers.
>> According to PMBUS spec, there is no protection associated with that
>> command. It just tells when the output voltage is considered good, when
>> it is not. What it does after that really depends the device, it may
>> drive a pin for example (or an LED indicator in my case).
>> 
>
> It is much more likely that it connects to the reset signal on the board,
> or it enables/disables power to parts of the board.

That's not what PMBus spec says about it:

"""
15.32. POWER_GOOD Signal Limits
For PMBus devices that offer a POWER_GOOD signal, these commands are used for
setting the output voltage at which a power good signal should be asserted and negated.
Power Good signals will be device and manufacturer specific. Many factors other than
output voltage may be used to determine whether or not the POWER_GOOD signal is to
be asserted. PMBus device users are instructed to consult the device manufacturer’s
product literature for the specifics of the device they are using.
"""

It's only supposed to have an effect on the power_good signal, not the
reset. I guess someone could wire that signal to a reset. Same could be
done with the alert or the fault one, I suppose

>
>> It is very similar to 'crit' or other limits in that sense,
>> I think. I don't really get why such property is not OK in hwmon then
>> and why it should not be configurable, if the other limits are ?
>> 
>
> Its use is for hardware control, not monitoring, even if it may be connected
> to a status LED. MAX15301, for example, groups the command under "Voltage
> Sequencing Commands".
>
> On top of that, the voltages are value/hysteresis values. The "off" voltage
> is lower than the "on" voltage.
>
> TPS25990 doesn't even support the command according to its datasheet, so I am
> at loss about your use case in the context of this patch series (the PGOOD pin
> on this chip signals to the downstream load that it is ok to draw
> power).

It does support GOOD_OFF, althought TI renamed the register to
VOUT_PGTH (Section 8.3.14.7.1.52, p87):

"""
VOUT_PGTH is a standard PMBus® command for setting or reading an 8-bit
output voltage threshold at which Power Good (PGOOD) is be de-asserted.
"""

Same as the PMBus spec. Changing the value through this command does
affect the signal as intented. How the signal is depends on the
implementation. It just drives an LED on the EVM.

Anyway, I don't want to hold things on this. I'll drop it from the next version.

>
> Guenter

-- 
Jerome





[Index of Archives]     [LM Sensors]     [Linux Sound]     [ALSA Users]     [ALSA Devel]     [Linux Audio Users]     [Linux Media]     [Kernel]     [Gimp]     [Yosemite News]     [Linux Media]

  Powered by Linux