[PATCH v3 6/7] arm64: dts: rockchip: hook up the MCU on the QNAP TS433

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



The MCU is an important part of the device functionality. It provides
functionality like fan-control, more leds, etc and even more important
without it, the NAS-device cannot even fully turned off.

Hook up the serial device to its uart and hook into the thermal
management to control the fan according to the cpu temperature.

While the MCU also provides a temperature sensor for the case, this one
is just polled and does not provide functionality for handling trip
points in hardware, so a lot of polling would be involved.
As the cpu is only cooled passively in these devices, it's temperature
rising will indicate the temperature level of the system just earlier.

Signed-off-by: Heiko Stuebner <heiko@xxxxxxxxx>
---
 .../boot/dts/rockchip/rk3568-qnap-ts433.dts   | 54 +++++++++++++++++++
 1 file changed, 54 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts b/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts
index 6c4269b3d9597..bff21684a3970 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts
@@ -465,6 +465,54 @@ rgmii_phy0: ethernet-phy@0 {
 	};
 };
 
+/*
+ * The MCU can provide system temperature too, but only by polling and of
+ * course also cannot set trip points. So attach to the cpu thermal-zone
+ * instead to control the fan.
+ */
+&cpu_thermal {
+	trips {
+		case_fan0: case-fan0 {
+			hysteresis = <2000>;
+			temperature = <35000>;
+			type = "active";
+		};
+
+		case_fan1: case-fan1 {
+			hysteresis = <2000>;
+			temperature = <45000>;
+			type = "active";
+		};
+
+		case_fan2: case-fan2 {
+			hysteresis = <2000>;
+			temperature = <65000>;
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		/*
+		 * Always provide some air movement, due to small case
+		 * full of harddrives.
+		 */
+		map1 {
+			cooling-device = <&fan THERMAL_NO_LIMIT 1>;
+			trip = <&case_fan0>;
+		};
+
+		map2 {
+			cooling-device = <&fan 2 3>;
+			trip = <&case_fan1>;
+		};
+
+		map3 {
+			cooling-device = <&fan 4 THERMAL_NO_LIMIT>;
+			trip = <&case_fan2>;
+		};
+	};
+};
+
 &pcie30phy {
 	data-lanes = <1 2>;
 	status = "okay";
@@ -563,6 +611,12 @@ &tsadc {
  */
 &uart0 {
 	status = "okay";
+
+	fan: mcu {
+		compatible = "qnap,ts433-mcu";
+		#cooling-cells = <2>;
+		cooling-levels = <0 64 89 128 166 204 221 238>;
+	};
 };
 
 /*
-- 
2.39.2





[Index of Archives]     [LM Sensors]     [Linux Sound]     [ALSA Users]     [ALSA Devel]     [Linux Audio Users]     [Linux Media]     [Kernel]     [Gimp]     [Yosemite News]     [Linux Media]

  Powered by Linux