Re: [PATCH 1/2] sbrmi: Use regmap subsystem

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 5/2/24 15:05, Naveen Krishna Chatradhi wrote:
From: Naveen Krishna Chatradhi <naveenkrishna.chatradhi@xxxxxxx>

- regmap subsystem provides multiple benefits over direct smbus APIs
- The susbsytem can be helpful in following cases
   - Differnet types of bus (i2c/i3c)
   - Different Register address size (1byte/2byte)

Signed-off-by: Akshay Gupta <Akshay.Gupta@xxxxxxx>
Signed-off-by: Naveen Krishna Chatradhi <naveenkrishna.chatradhi@xxxxxxx>
---
  drivers/hwmon/Kconfig |  1 +
  drivers/hwmon/sbrmi.c | 61 ++++++++++++++++++++++++-------------------
  2 files changed, 35 insertions(+), 27 deletions(-)

diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index a608264da87d..903a8ebbd2d7 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -1759,6 +1759,7 @@ config SENSORS_SBTSI
  config SENSORS_SBRMI
  	tristate "Emulated SB-RMI sensor"
  	depends on I2C
+	select REGMAP_I2C
  	help
  	  If you say yes here you get support for emulated RMI
  	  sensors on AMD SoCs with APML interface connected to a BMC device.
diff --git a/drivers/hwmon/sbrmi.c b/drivers/hwmon/sbrmi.c
index 484703f0ea5f..901bd82d71d4 100644
--- a/drivers/hwmon/sbrmi.c
+++ b/drivers/hwmon/sbrmi.c
@@ -14,6 +14,7 @@
  #include <linux/module.h>
  #include <linux/mutex.h>
  #include <linux/of.h>
+#include <linux/regmap.h>

  /* Do not allow setting negative power limit */
  #define SBRMI_PWR_MIN	0
@@ -63,6 +64,7 @@ enum sbrmi_reg {
  struct sbrmi_data {
  	struct i2c_client *client;

There is only one user of this structure left, and it is for a
questionable error message (questionable since all other errors
are handled silently). I would suggest to drop both.


  	struct mutex lock;
+	struct regmap *regmap;
  	u32 pwr_limit_max;
  };

@@ -73,22 +75,21 @@ struct sbrmi_mailbox_msg {
  	u32 data_out;
  };

-static int sbrmi_enable_alert(struct i2c_client *client)
+static int sbrmi_enable_alert(struct sbrmi_data *data)
  {
-	int ctrl;
+	int ctrl, ret = 0;

Unnecessary initialization

  	/*
  	 * Enable the SB-RMI Software alert status
  	 * by writing 0 to bit 4 of Control register(0x1)
  	 */
-	ctrl = i2c_smbus_read_byte_data(client, SBRMI_CTRL);
-	if (ctrl < 0)
-		return ctrl;
+	ret = regmap_read(data->regmap, SBRMI_STATUS, &ctrl);
+	if (ret < 0)
+		return ret;

  	if (ctrl & 0x10) {
  		ctrl &= ~0x10;
-		return i2c_smbus_write_byte_data(client,
-						 SBRMI_CTRL, ctrl);
+		return regmap_write(data->regmap, SBRMI_CTRL, ctrl);
  	}

  	return 0;
@@ -97,6 +98,7 @@ static int sbrmi_enable_alert(struct i2c_client *client)
  static int rmi_mailbox_xfer(struct sbrmi_data *data,
  			    struct sbrmi_mailbox_msg *msg)
  {
+	unsigned int bytes = 0;

Unnecessary initialization

  	int i, ret, retry = 10;
  	int sw_status;
  	u8 byte;
@@ -104,14 +106,12 @@ static int rmi_mailbox_xfer(struct sbrmi_data *data,
  	mutex_lock(&data->lock);

  	/* Indicate firmware a command is to be serviced */
-	ret = i2c_smbus_write_byte_data(data->client,
-					SBRMI_INBNDMSG7, START_CMD);
+	ret = regmap_write(data->regmap, SBRMI_INBNDMSG7, START_CMD);
  	if (ret < 0)
  		goto exit_unlock;

  	/* Write the command to SBRMI::InBndMsg_inst0 */
-	ret = i2c_smbus_write_byte_data(data->client,
-					SBRMI_INBNDMSG0, msg->cmd);
+	ret = regmap_write(data->regmap, SBRMI_INBNDMSG0, msg->cmd);
  	if (ret < 0)
  		goto exit_unlock;

@@ -122,8 +122,7 @@ static int rmi_mailbox_xfer(struct sbrmi_data *data,
  	 */
  	for (i = 0; i < 4; i++) {
  		byte = (msg->data_in >> i * 8) & 0xff;
-		ret = i2c_smbus_write_byte_data(data->client,
-						SBRMI_INBNDMSG1 + i, byte);
+		ret = regmap_write(data->regmap, SBRMI_INBNDMSG1 + i, byte);
  		if (ret < 0)
  			goto exit_unlock;
  	}
@@ -132,8 +131,7 @@ static int rmi_mailbox_xfer(struct sbrmi_data *data,
  	 * Write 0x01 to SBRMI::SoftwareInterrupt to notify firmware to
  	 * perform the requested read or write command
  	 */
-	ret = i2c_smbus_write_byte_data(data->client,
-					SBRMI_SW_INTERRUPT, TRIGGER_MAILBOX);
+	ret = regmap_write(data->regmap, SBRMI_SW_INTERRUPT, TRIGGER_MAILBOX);
  	if (ret < 0)
  		goto exit_unlock;

@@ -143,8 +141,7 @@ static int rmi_mailbox_xfer(struct sbrmi_data *data,
  	 * of the requested command
  	 */
  	do {
-		sw_status = i2c_smbus_read_byte_data(data->client,
-						     SBRMI_STATUS);
+		ret = regmap_read(data->regmap, SBRMI_STATUS, &sw_status);
  		if (sw_status < 0) {
  			ret = sw_status;
  			goto exit_unlock;
@@ -168,11 +165,11 @@ static int rmi_mailbox_xfer(struct sbrmi_data *data,
  	 */
  	if (msg->read) {
  		for (i = 0; i < 4; i++) {
-			ret = i2c_smbus_read_byte_data(data->client,
-						       SBRMI_OUTBNDMSG1 + i);
+			ret = regmap_read(data->regmap,
+					  SBRMI_OUTBNDMSG1 + i, &bytes);
  			if (ret < 0)
  				goto exit_unlock;
-			msg->data_out |= ret << i * 8;
+			msg->data_out |= bytes << i * 8;
  		}
  	}

@@ -180,9 +177,8 @@ static int rmi_mailbox_xfer(struct sbrmi_data *data,
  	 * BMC must write 1'b1 to SBRMI::Status[SwAlertSts] to clear the
  	 * ALERT to initiator
  	 */
-	ret = i2c_smbus_write_byte_data(data->client, SBRMI_STATUS,
-					sw_status | SW_ALERT_MASK);
-
+	ret = regmap_write(data->regmap, SBRMI_STATUS,
+			   sw_status | SW_ALERT_MASK);
  exit_unlock:
  	mutex_unlock(&data->lock);
  	return ret;
@@ -265,7 +261,7 @@ static umode_t sbrmi_is_visible(const void *data,
  	return 0;
  }

-static const struct hwmon_channel_info * const sbrmi_info[] = {
+static const struct hwmon_channel_info *sbrmi_info[] = {
  	HWMON_CHANNEL_INFO(power,
  			   HWMON_P_INPUT | HWMON_P_CAP | HWMON_P_CAP_MAX),
  	NULL
@@ -302,6 +298,10 @@ static int sbrmi_probe(struct i2c_client *client)
  	struct device *dev = &client->dev;
  	struct device *hwmon_dev;
  	struct sbrmi_data *data;
+	struct regmap_config sbrmi_i2c_regmap_config = {
+		.reg_bits = 8,
+		.val_bits = 8,
+	};
  	int ret;

  	data = devm_kzalloc(dev, sizeof(struct sbrmi_data), GFP_KERNEL);
@@ -310,9 +310,12 @@ static int sbrmi_probe(struct i2c_client *client)

  	data->client = client;
  	mutex_init(&data->lock);
+	data->regmap = devm_regmap_init_i2c(client, &sbrmi_i2c_regmap_config);
+	if (IS_ERR(data->regmap))
+		return PTR_ERR(data->regmap);

  	/* Enable alert for SB-RMI sequence */
-	ret = sbrmi_enable_alert(client);
+	ret = sbrmi_enable_alert(data);
  	if (ret < 0)
  		return ret;

@@ -321,8 +324,12 @@ static int sbrmi_probe(struct i2c_client *client)
  	if (ret < 0)
  		return ret;

-	hwmon_dev = devm_hwmon_device_register_with_info(dev, client->name, data,
-							 &sbrmi_chip_info, NULL);
+	dev_set_drvdata(dev, (void *)data);
+

Why would this be needed ? On a side note, the typecast is unnecessary.

Guenter





[Index of Archives]     [LM Sensors]     [Linux Sound]     [ALSA Users]     [ALSA Devel]     [Linux Audio Users]     [Linux Media]     [Kernel]     [Gimp]     [Yosemite News]     [Linux Media]

  Powered by Linux