On 9/13/23 08:40, Krzysztof Kozlowski wrote:
On 13/09/2023 17:21, Daniel Matyas wrote:
Subject: not much improved. I am sorry, but you are not adding new
properties to entire devicetree of entire world. You are actually not
adding anything to any devicetree, because these are bindings (which is
obvious, as said by prefix).
You got comments on this.
These attributes are:
- adi,comp-int - boolean property
- adi,alrm-pol - can be 0, 1 (if not present, default value)
- adi,flt-q - can be 1, 2, 4, 8 (if not present, default value)
- adi,timeout-enable - boolean property
Don't repeat what the code does. Explain why you are adding it, what is
the purpose.
These modify the corresponding bits in the configuration register.
Signed-off-by: Daniel Matyas <daniel.matyas@xxxxxxxxxx>
---
.../bindings/hwmon/adi,max31827.yaml | 35 +++++++++++++++++++
1 file changed, 35 insertions(+)
diff --git a/Documentation/devicetree/bindings/hwmon/adi,max31827.yaml b/Documentation/devicetree/bindings/hwmon/adi,max31827.yaml
index 2dc8b07b4d3b..6bde71bdb8dd 100644
--- a/Documentation/devicetree/bindings/hwmon/adi,max31827.yaml
+++ b/Documentation/devicetree/bindings/hwmon/adi,max31827.yaml
@@ -32,6 +32,37 @@ properties:
Must have values in the interval (1.6V; 3.6V) in order for the device to
function correctly.
+ adi,comp-int:
+ description:
+ If present interrupt mode is used. If not present comparator mode is used
+ (default).
Why this is a property of hardware?
Because it affects the behavior of the interrupt signal and whatever
it is connected to. For example, it could be connected to an interrupt
controller (interupt mode), or it could be connected to a fan which is
enabled while the signal is active (comparator mode).
+ type: boolean
+
+ adi,alrm-pol:
+ description:
+ Sets the alarms active state.
+ - 0 = active low
+ - 1 = active high
+ For max31827 and max31828 the default alarm polarity is low. For max31829
+ it is high.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1]
+
+ adi,flt-q:
+ description:
+ Select how many consecutive temperature faults must occur before
+ overtemperature or undertemperature faults are indicated in the
+ corresponding status bits.
+ For max31827 default fault queue is 1. For max31828 and max31829 it is 4.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [1, 2, 4, 8]
+
+ adi,timeout-enable:
+ description:
+ Enables timeout. Bus timeout resets the I2C-compatible interface when SCL
+ is low for more than 30ms (nominal).
Why this is a property of hardware?
Because it affects i2c bus operation.
I am not sure I understand what you are trying to say here.
This is a much a "hardware" property as the i2c bus speed
and many similar properties, and the need for it is system
dependent (for example, a system with many devices on the
i2c bus or with a less than perfect i2c controller may need
it because the bus tends to get stuck).
Those are not properties where one would, at runtime,
decide to enable bus timeout or the interrupt mode or
the bus speed. Typically that kind of functionality
has to be configured early when the system is started.
If devicetree must not or no longer be used to describe the
system to a point where it can be configured to get it
to a working state, what is the suggested alternative ?
Guenter
