On Tue, Feb 14, 2023 at 11:02:19PM +0100, Leonard Anderweit wrote:
> Add information on the Aquacomputer Aquaero control report and disable the
> control report checksum for Aquaero. The Aquaero does not use the checksum so
> it must be disabled to avoid overwriting the last two bytes of the control
> report.
>
> Signed-off-by: Leonard Anderweit <leonard.anderweit@xxxxxxxxx>
Applied. And again:
WARNING: Possible unwrapped commit description (prefer a maximum 75 chars per line)
#85:
control report checksum for Aquaero. The Aquaero does not use the checksum so
Please keep in mind that you are causing extra work for me.
Guenter
> ---
> drivers/hwmon/aquacomputer_d5next.c | 31 ++++++++++++++++++++++++-----
> 1 file changed, 26 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/hwmon/aquacomputer_d5next.c b/drivers/hwmon/aquacomputer_d5next.c
> index 535d2fc0e55c..eb185318098a 100644
> --- a/drivers/hwmon/aquacomputer_d5next.c
> +++ b/drivers/hwmon/aquacomputer_d5next.c
> @@ -56,6 +56,7 @@ static const char *const aqc_device_names[] = {
> #define SERIAL_PART_OFFSET 2
>
> #define CTRL_REPORT_ID 0x03
> +#define AQUAERO_CTRL_REPORT_ID 0x0b
>
> /* The HID report that the official software always sends
> * after writing values, currently same for all devices
> @@ -67,6 +68,14 @@ static u8 secondary_ctrl_report[] = {
> 0x02, 0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x34, 0xC6
> };
>
> +/* Secondary HID report values for Aquaero */
> +#define AQUAERO_SECONDARY_CTRL_REPORT_ID 0x06
> +#define AQUAERO_SECONDARY_CTRL_REPORT_SIZE 0x07
> +
> +static u8 aquaero_secondary_ctrl_report[] = {
> + 0x06, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00
> +};
> +
> /* Report IDs for legacy devices */
> #define POWERADJUST3_STATUS_REPORT_ID 0x03
>
> @@ -94,6 +103,7 @@ static u8 secondary_ctrl_report[] = {
> #define AQUAERO_NUM_VIRTUAL_SENSORS 8
> #define AQUAERO_NUM_CALC_VIRTUAL_SENSORS 4
> #define AQUAERO_NUM_FLOW_SENSORS 2
> +#define AQUAERO_CTRL_REPORT_SIZE 0xa93
>
> /* Sensor report offsets for Aquaero fan controllers */
> #define AQUAERO_SENSOR_START 0x65
> @@ -531,12 +541,16 @@ static int aqc_send_ctrl_data(struct aqc_data *priv)
> int ret;
> u16 checksum;
>
> - /* Init and xorout value for CRC-16/USB is 0xffff */
> - checksum = crc16(0xffff, priv->buffer + priv->checksum_start, priv->checksum_length);
> - checksum ^= 0xffff;
> + /* Checksum is not needed for Aquaero */
> + if (priv->kind != aquaero) {
> + /* Init and xorout value for CRC-16/USB is 0xffff */
> + checksum = crc16(0xffff, priv->buffer + priv->checksum_start,
> + priv->checksum_length);
> + checksum ^= 0xffff;
>
> - /* Place the new checksum at the end of the report */
> - put_unaligned_be16(checksum, priv->buffer + priv->checksum_offset);
> + /* Place the new checksum at the end of the report */
> + put_unaligned_be16(checksum, priv->buffer + priv->checksum_offset);
> + }
>
> /* Send the patched up report back to the device */
> ret = hid_hw_raw_request(priv->hdev, priv->ctrl_report_id, priv->buffer, priv->buffer_size,
> @@ -1280,6 +1294,8 @@ static int aqc_probe(struct hid_device *hdev, const struct hid_device_id *id)
> priv->num_flow_sensors = AQUAERO_NUM_FLOW_SENSORS;
> priv->flow_sensors_start_offset = AQUAERO_FLOW_SENSORS_START;
>
> + priv->buffer_size = AQUAERO_CTRL_REPORT_SIZE;
> +
> priv->temp_label = label_temp_sensors;
> priv->virtual_temp_label = label_virtual_temp_sensors;
> priv->calc_virt_temp_label = label_aquaero_calc_temp_sensors;
> @@ -1443,6 +1459,11 @@ static int aqc_probe(struct hid_device *hdev, const struct hid_device_id *id)
> priv->firmware_version_offset = AQUAERO_FIRMWARE_VERSION;
>
> priv->fan_structure = &aqc_aquaero_fan_structure;
> +
> + priv->ctrl_report_id = AQUAERO_CTRL_REPORT_ID;
> + priv->secondary_ctrl_report_id = AQUAERO_SECONDARY_CTRL_REPORT_ID;
> + priv->secondary_ctrl_report_size = AQUAERO_SECONDARY_CTRL_REPORT_SIZE;
> + priv->secondary_ctrl_report = aquaero_secondary_ctrl_report;
> break;
> case poweradjust3:
> priv->status_report_id = POWERADJUST3_STATUS_REPORT_ID;
