Re: [PATCH v3] hwmon: (aquacomputer_d5next) Add support for Aquacomputer Octo

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sun, Mar 27, 2022 at 09:04:46AM +0200, Aleksa Savic wrote:
> Extend aquacomputer_d5next driver to expose hardware temperature sensors
> and fans of the Aquacomputer Octo fan controller, which communicates
> through a proprietary USB HID protocol.
> 
> Four temperature sensors and eight PWM controllable fans are available.
> Additionally, serial number, firmware version and power-on count are
> exposed through debugfs.
> 
> This driver has been tested on x86_64.
> 
> Signed-off-by: Aleksa Savic <savicaleksa83@xxxxxxxxx>
> ---
> Changes in v3:
> - Added break; statements where needed
> - aqc_set_ctrl_val() now only sets values with a length of 2
> - Replace goto with return in aqc_send_ctrl_data()
> 
> Changes in v2:
> - Fixed formatting
> - HID report values from device are now being converted sooner
> - aqc_pwm_to_percent() is now range checked
> - Put pointers to labels in aqc_data
> - Simplified checksum calculation call
> ---
>  Documentation/hwmon/aquacomputer_d5next.rst |   4 +
>  drivers/hwmon/Kconfig                       |   7 +-
>  drivers/hwmon/aquacomputer_d5next.c         | 431 +++++++++++++++++---
>  3 files changed, 390 insertions(+), 52 deletions(-)
> 
> diff --git a/Documentation/hwmon/aquacomputer_d5next.rst b/Documentation/hwmon/aquacomputer_d5next.rst
> index 3373e27b707d..e69f718caf5b 100644
> --- a/Documentation/hwmon/aquacomputer_d5next.rst
> +++ b/Documentation/hwmon/aquacomputer_d5next.rst
> @@ -7,6 +7,7 @@ Supported devices:
>  
>  * Aquacomputer D5 Next watercooling pump
>  * Aquacomputer Farbwerk 360 RGB controller
> +* Aquacomputer Octo fan controller
>  
>  Author: Aleksa Savic
>  
> @@ -28,6 +29,9 @@ seems to require sending it a complete configuration. That includes addressable
>  RGB LEDs, for which there is no standard sysfs interface. Thus, that task is
>  better suited for userspace tools.
>  
> +The Octo exposes four temperature sensors and eight PWM controllable fans, along
> +with their speed (in RPM), power, voltage and current.
> +
>  The Farbwerk 360 exposes four temperature sensors. Depending on the device,
>  not all sysfs and debugfs entries will be available.
>  
> diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
> index db8bc55e5f50..5beadd8a0932 100644
> --- a/drivers/hwmon/Kconfig
> +++ b/drivers/hwmon/Kconfig
> @@ -256,11 +256,12 @@ config SENSORS_AHT10
>  	  will be called aht10.
>  
>  config SENSORS_AQUACOMPUTER_D5NEXT
> -	tristate "Aquacomputer D5 Next watercooling pump"
> +	tristate "Aquacomputer D5 Next, Octo and Farbwerk 360"
>  	depends on USB_HID
>  	help
> -	  If you say yes here you get support for the Aquacomputer D5 Next
> -	  watercooling pump sensors.
> +	  If you say yes here you get support for sensors and fans of
> +	  the Aquacomputer D5 Next watercooling pump, Octo fan
> +	  controller and Farbwerk 360 RGB controller, where available.
>  
>  	  This driver can also be built as a module. If so, the module
>  	  will be called aquacomputer_d5next.
> diff --git a/drivers/hwmon/aquacomputer_d5next.c b/drivers/hwmon/aquacomputer_d5next.c
> index 525809cf7c95..cd008bfa03be 100644
> --- a/drivers/hwmon/aquacomputer_d5next.c
> +++ b/drivers/hwmon/aquacomputer_d5next.c
> @@ -1,6 +1,6 @@
>  // SPDX-License-Identifier: GPL-2.0+
>  /*
> - * hwmon driver for Aquacomputer devices (D5 Next, Farbwerk 360)
> + * hwmon driver for Aquacomputer devices (D5 Next, Farbwerk 360, Octo)
>   *
>   * Aquacomputer devices send HID reports (with ID 0x01) every second to report
>   * sensor values.
> @@ -8,23 +8,27 @@
>   * Copyright 2021 Aleksa Savic <savicaleksa83@xxxxxxxxx>
>   */
>  
> +#include <linux/crc16.h>
>  #include <linux/debugfs.h>
>  #include <linux/hid.h>
>  #include <linux/hwmon.h>
>  #include <linux/jiffies.h>
>  #include <linux/module.h>
> +#include <linux/mutex.h>
>  #include <linux/seq_file.h>
>  #include <asm/unaligned.h>
>  
>  #define USB_VENDOR_ID_AQUACOMPUTER	0x0c70
>  #define USB_PRODUCT_ID_D5NEXT		0xf00e
>  #define USB_PRODUCT_ID_FARBWERK360	0xf010
> +#define USB_PRODUCT_ID_OCTO		0xf011
>  
> -enum kinds { d5next, farbwerk360 };
> +enum kinds { d5next, farbwerk360, octo };
>  
>  static const char *const aqc_device_names[] = {
>  	[d5next] = "d5next",
> -	[farbwerk360] = "farbwerk360"
> +	[farbwerk360] = "farbwerk360",
> +	[octo] = "octo"
>  };
>  
>  #define DRIVER_NAME			"aquacomputer_d5next"
> @@ -35,6 +39,18 @@ static const char *const aqc_device_names[] = {
>  #define SERIAL_SECOND_PART		5
>  #define FIRMWARE_VERSION		13
>  
> +#define CTRL_REPORT_ID			0x03
> +
> +/* The HID report that the official software always sends
> + * after writing values, currently same for all devices
> + */
> +#define SECONDARY_CTRL_REPORT_ID	0x02
> +#define SECONDARY_CTRL_REPORT_SIZE	0x0B
> +
> +static u8 secondary_ctrl_report[] = {
> +	0x02, 0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x34, 0xC6
> +};
> +
>  /* Register offsets for the D5 Next pump */
>  #define D5NEXT_POWER_CYCLES		24
>  
> @@ -55,12 +71,38 @@ static const char *const aqc_device_names[] = {
>  
>  /* Register offsets for the Farbwerk 360 RGB controller */
>  #define FARBWERK360_NUM_SENSORS		4
> -#define FARBWERK360_SENSOR_START		0x32
> +#define FARBWERK360_SENSOR_START	0x32
>  #define FARBWERK360_SENSOR_SIZE		0x02
>  #define FARBWERK360_SENSOR_DISCONNECTED	0x7FFF
>  
> +/* Register offsets for the Octo fan controller */
> +#define OCTO_POWER_CYCLES		0x18
> +#define OCTO_NUM_FANS			8
> +#define OCTO_FAN_PERCENT_OFFSET		0x00
> +#define OCTO_FAN_VOLTAGE_OFFSET		0x02
> +#define OCTO_FAN_CURRENT_OFFSET		0x04
> +#define OCTO_FAN_POWER_OFFSET		0x06
> +#define OCTO_FAN_SPEED_OFFSET		0x08
> +
> +static u8 octo_sensor_fan_offsets[] = { 0x7D, 0x8A, 0x97, 0xA4, 0xB1, 0xBE, 0xCB, 0xD8 };
> +
> +#define OCTO_NUM_SENSORS		4
> +#define OCTO_SENSOR_START		0x3D
> +#define OCTO_SENSOR_SIZE		0x02
> +#define OCTO_SENSOR_DISCONNECTED	0x7FFF
> +
> +#define OCTO_CTRL_REPORT_SIZE			0x65F
> +#define OCTO_CTRL_REPORT_CHECKSUM_OFFSET	0x65D
> +#define OCTO_CTRL_REPORT_CHECKSUM_START		0x01
> +#define OCTO_CTRL_REPORT_CHECKSUM_LENGTH	0x65C
> +
> +/* Fan speed registers in Octo control report (from 0-100%) */
> +static u16 octo_ctrl_fan_offsets[] = { 0x5B, 0xB0, 0x105, 0x15A, 0x1AF, 0x204, 0x259, 0x2AE };
> +
>  /* Labels for D5 Next */
> -#define L_D5NEXT_COOLANT_TEMP		"Coolant temp"
> +static const char *const label_d5next_temp[] = {
> +	"Coolant temp"
> +};
>  
>  static const char *const label_d5next_speeds[] = {
>  	"Pump speed",
> @@ -83,7 +125,7 @@ static const char *const label_d5next_current[] = {
>  	"Fan current"
>  };
>  
> -/* Labels for Farbwerk 360 temperature sensors */
> +/* Labels for Farbwerk 360 and Octo temperature sensors */
>  static const char *const label_temp_sensors[] = {
>  	"Sensor 1",
>  	"Sensor 2",
> @@ -91,32 +133,180 @@ static const char *const label_temp_sensors[] = {
>  	"Sensor 4"
>  };
>  
> +/* Labels for Octo */
> +static const char *const label_fan_speed[] = {
> +	"Fan 1 speed",
> +	"Fan 2 speed",
> +	"Fan 3 speed",
> +	"Fan 4 speed",
> +	"Fan 5 speed",
> +	"Fan 6 speed",
> +	"Fan 7 speed",
> +	"Fan 8 speed"
> +};
> +
> +static const char *const label_fan_power[] = {
> +	"Fan 1 power",
> +	"Fan 2 power",
> +	"Fan 3 power",
> +	"Fan 4 power",
> +	"Fan 5 power",
> +	"Fan 6 power",
> +	"Fan 7 power",
> +	"Fan 8 power"
> +};
> +
> +static const char *const label_fan_voltage[] = {
> +	"Fan 1 voltage",
> +	"Fan 2 voltage",
> +	"Fan 3 voltage",
> +	"Fan 4 voltage",
> +	"Fan 5 voltage",
> +	"Fan 6 voltage",
> +	"Fan 7 voltage",
> +	"Fan 8 voltage"
> +};
> +
> +static const char *const label_fan_current[] = {
> +	"Fan 1 current",
> +	"Fan 2 current",
> +	"Fan 3 current",
> +	"Fan 4 current",
> +	"Fan 5 current",
> +	"Fan 6 current",
> +	"Fan 7 current",
> +	"Fan 8 current"
> +};
> +
>  struct aqc_data {
>  	struct hid_device *hdev;
>  	struct device *hwmon_dev;
>  	struct dentry *debugfs;
> +	struct mutex mutex;	/* Used for locking access when reading and writing PWM values */
>  	enum kinds kind;
>  	const char *name;
>  
> +	int buffer_size;
> +	u8 *buffer;
> +	int checksum_start;
> +	int checksum_length;
> +	int checksum_offset;
> +
>  	/* General info, same across all devices */
>  	u32 serial_number[2];
>  	u16 firmware_version;
>  
> -	/* D5 Next specific - how many times the device was powered on */
> +	/* How many times the device was powered on */
>  	u32 power_cycles;
>  
>  	/* Sensor values */
>  	s32 temp_input[4];
> -	u16 speed_input[2];
> -	u32 power_input[2];
> -	u16 voltage_input[3];
> -	u16 current_input[2];
> +	u16 speed_input[8];
> +	u32 power_input[8];
> +	u16 voltage_input[8];
> +	u16 current_input[8];
> +
> +	/* Label values */
> +	const char *const *temp_label;
> +	const char *const *speed_label;
> +	const char *const *power_label;
> +	const char *const *voltage_label;
> +	const char *const *current_label;
>  
>  	unsigned long updated;
>  };
>  
> -static umode_t aqc_is_visible(const void *data, enum hwmon_sensor_types type, u32 attr,
> -			      int channel)
> +static int aqc_percent_to_pwm(u16 val)

I am sure I asked this before. The calculation looks like a conversion
from centi-percent to pwm, not from percent to pwm. Please either reflect
that in the function name or add a comment.

Thanks,
Guenter



[Index of Archives]     [LM Sensors]     [Linux Sound]     [ALSA Users]     [ALSA Devel]     [Linux Audio Users]     [Linux Media]     [Kernel]     [Gimp]     [Yosemite News]     [Linux Media]

  Powered by Linux