Am 2022-03-31 19:28, schrieb Guenter Roeck:
+static int lan966x_hwmon_write_pwm_freq(struct device *dev, long val)
+{
+ struct lan966x_hwmon *hwmon = dev_get_drvdata(dev);
+
+ val = DIV_ROUND_CLOSEST(hwmon->clk_rate, val);
I must have looked at this for an hour, but I didn't see the problem.
Sorry for that. Try writing "0" as new pwm frequency.
Ohh, and negative values..
I'll add a
if (val <= 0)
return -EINVAL;
+static int lan966x_hwmon_enable(struct lan966x_hwmon *hwmon)
+{
+ unsigned int mask = SENSOR_CFG_SAMPLE_ENA |
+ SENSOR_CFG_START_CAPTURE |
+ SENSOR_CFG_CONTINIOUS_MODE |
+ SENSOR_CFG_PSAMPLE_ENA;
+ unsigned int val;
+
+ /* enable continuous mode */
+ val = SENSOR_CFG_SAMPLE_ENA | SENSOR_CFG_CONTINIOUS_MODE;
+
I am curious: Why not as part of the assignment, similar to 'mask' ?
There was code to set the clock divider, but I've removed
it as the hardware has a sane default. That left just that one
line, but moving the comment above the declaration looked
weird.
Now thinking about it again, it might make sense to bring
back the code to set the clock divider in case someone
will fiddle around with it before the driver is probed.
#define LAN966X_PVT_CLK 1200000 /* 1.2 MHz */
/* set PVT clock to be between 1.15 and 1.25 MHz */
div = DIV_ROUND_CLOSEST(hwmon->clk_rate, LAN966X_PVT_CLK);
val |= FIELD_PREP(SENSOR_CFG_CLK_CFG, div);
+static int lan966x_hwmon_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct lan966x_hwmon *hwmon;
+ struct device *hwmon_dev;
+ int ret;
+
+ hwmon = devm_kzalloc(dev, sizeof(*hwmon), GFP_KERNEL);
+ if (!hwmon)
+ return -ENOMEM;
+
+ hwmon->clk = devm_clk_get(dev, NULL);
+ if (IS_ERR(hwmon->clk))
+ return dev_err_probe(dev, PTR_ERR(hwmon->clk),
+ "failed to get clock\n");
+
+ ret = lan966x_clk_enable(dev, hwmon);
+ if (ret)
+ return dev_err_probe(dev, ret, "failed to enable clock\n");
+
+ hwmon->clk_rate = clk_get_rate(hwmon->clk);
+
+ hwmon->regmap_pvt = lan966x_init_regmap(pdev, "pvt");
+ if (IS_ERR(hwmon->regmap_pvt))
+ return dev_err_probe(dev, PTR_ERR(hwmon->regmap_pvt),
+ "failed to get regmap for PVT registers\n");
+
+ hwmon->regmap_fan = lan966x_init_regmap(pdev, "fan");
+ if (IS_ERR(hwmon->regmap_fan))
+ return dev_err_probe(dev, PTR_ERR(hwmon->regmap_fan),
+ "failed to get regmap for fan registers\n");
+
+ hwmon_dev = devm_hwmon_device_register_with_info(&pdev->dev,
+ "lan966x_hwmon", hwmon,
+ &lan966x_hwmon_chip_info, NULL);
+ if (IS_ERR(hwmon_dev))
+ return dev_err_probe(dev, PTR_ERR(hwmon_dev),
+ "failed to register hwmon device\n");
+
+ return lan966x_hwmon_enable(hwmon);
Since I am nitpicking: It may make sense to call this function before
registering the hwmon device, and it may make sense to disable sampling
when unloading the driver (you could trigger that by calling
devm_add_action_or_reset() from lan966x_hwmon_enable).
sure
-michael
