On Mon, Feb 21, 2022 at 10:42:06AM +0100, Marcello Sylvester Bauer wrote: > PLI1209BC is a Digital Supervisor from Vicor Corporation. > > Signed-off-by: Marcello Sylvester Bauer <sylv@xxxxxxx> Applied to hwmon-next. Thanks, Guenter > --- > Documentation/hwmon/index.rst | 1 + > Documentation/hwmon/pli1209bc.rst | 75 +++++++++++++++++++ > drivers/hwmon/pmbus/Kconfig | 9 +++ > drivers/hwmon/pmbus/Makefile | 1 + > drivers/hwmon/pmbus/pli1209bc.c | 115 ++++++++++++++++++++++++++++++ > 5 files changed, 201 insertions(+) > create mode 100644 Documentation/hwmon/pli1209bc.rst > create mode 100644 drivers/hwmon/pmbus/pli1209bc.c > > diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst > index b69fdaf1af82..075d1defcd20 100644 > --- a/Documentation/hwmon/index.rst > +++ b/Documentation/hwmon/index.rst > @@ -161,6 +161,7 @@ Hardware Monitoring Kernel Drivers > pc87427 > pcf8591 > pim4328 > + pli1209bc > pm6764tr > pmbus > powr1220 > diff --git a/Documentation/hwmon/pli1209bc.rst b/Documentation/hwmon/pli1209bc.rst > new file mode 100644 > index 000000000000..ea5b3f68a515 > --- /dev/null > +++ b/Documentation/hwmon/pli1209bc.rst > @@ -0,0 +1,75 @@ > +.. SPDX-License-Identifier: GPL-2.0 > + > +Kernel driver pli1209bc > +======================= > + > +Supported chips: > + > + * Digital Supervisor PLI1209BC > + > + Prefix: 'pli1209bc' > + > + Addresses scanned: 0x50 - 0x5F > + > + Datasheet: https://www.vicorpower.com/documents/datasheets/ds-PLI1209BCxyzz-VICOR.pdf > + > +Authors: > + - Marcello Sylvester Bauer <sylv@xxxxxxx> > + > +Description > +----------- > + > +The Vicor PLI1209BC is an isolated digital power system supervisor that provides > +a communication interface between a host processor and one Bus Converter Module > +(BCM). The PLI communicates with a system controller via a PMBus compatible > +interface over an isolated UART interface. Through the PLI, the host processor > +can configure, set protection limits, and monitor the BCM. > + > +Sysfs entries > +------------- > + > +======================= ======================================================== > +in1_label "vin2" > +in1_input Input voltage. > +in1_rated_min Minimum rated input voltage. > +in1_rated_max Maximum rated input voltage. > +in1_max Maximum input voltage. > +in1_max_alarm Input voltage high alarm. > +in1_crit Critical input voltage. > +in1_crit_alarm Input voltage critical alarm. > + > +in2_label "vout2" > +in2_input Output voltage. > +in2_rated_min Minimum rated output voltage. > +in2_rated_max Maximum rated output voltage. > +in2_alarm Output voltage alarm > + > +curr1_label "iin2" > +curr1_input Input current. > +curr1_max Maximum input current. > +curr1_max_alarm Maximum input current high alarm. > +curr1_crit Critical input current. > +curr1_crit_alarm Input current critical alarm. > + > +curr2_label "iout2" > +curr2_input Output current. > +curr2_crit Critical output current. > +curr2_crit_alarm Output current critical alarm. > +curr2_max Maximum output current. > +curr2_max_alarm Output current high alarm. > + > +power1_label "pin2" > +power1_input Input power. > +power1_alarm Input power alarm. > + > +power2_label "pout2" > +power2_input Output power. > +power2_rated_max Maximum rated output power. > + > +temp1_input Die temperature. > +temp1_alarm Die temperature alarm. > +temp1_max Maximum die temperature. > +temp1_max_alarm Die temperature high alarm. > +temp1_crit Critical die temperature. > +temp1_crit_alarm Die temperature critical alarm. > +======================= ======================================================== > diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig > index c73aa50c7615..f18f67a94697 100644 > --- a/drivers/hwmon/pmbus/Kconfig > +++ b/drivers/hwmon/pmbus/Kconfig > @@ -317,6 +317,15 @@ config SENSORS_PIM4328 > This driver can also be built as a module. If so, the module will > be called pim4328. > > +config SENSORS_PLI1209BC > + tristate "Vicor PLI1209BC" > + help > + If you say yes here you get hardware monitoring support for Vicor > + PLI1209BC Digital Supervisor. > + > + This driver can also be built as a module. If so, the module will > + be called pli1209bc. > + > config SENSORS_PM6764TR > tristate "ST PM6764TR" > help > diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile > index e5935f70c9e0..a4a96ac71de7 100644 > --- a/drivers/hwmon/pmbus/Makefile > +++ b/drivers/hwmon/pmbus/Makefile > @@ -33,6 +33,7 @@ obj-$(CONFIG_SENSORS_MAX8688) += max8688.o > obj-$(CONFIG_SENSORS_MP2888) += mp2888.o > obj-$(CONFIG_SENSORS_MP2975) += mp2975.o > obj-$(CONFIG_SENSORS_MP5023) += mp5023.o > +obj-$(CONFIG_SENSORS_PLI1209BC) += pli1209bc.o > obj-$(CONFIG_SENSORS_PM6764TR) += pm6764tr.o > obj-$(CONFIG_SENSORS_PXE1610) += pxe1610.o > obj-$(CONFIG_SENSORS_Q54SJ108A2) += q54sj108a2.o > diff --git a/drivers/hwmon/pmbus/pli1209bc.c b/drivers/hwmon/pmbus/pli1209bc.c > new file mode 100644 > index 000000000000..5f8847307e55 > --- /dev/null > +++ b/drivers/hwmon/pmbus/pli1209bc.c > @@ -0,0 +1,115 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Hardware monitoring driver for Vicor PLI1209BC Digital Supervisor > + * > + * Copyright (c) 2022 9elements GmbH > + */ > + > +#include <linux/i2c.h> > +#include <linux/module.h> > +#include <linux/pmbus.h> > +#include "pmbus.h" > + > +/* > + * The capability command is only supported at page 0. Probing the device while > + * the page register is set to 1 will falsely enable PEC support. Disable > + * capability probing accordingly, since the PLI1209BC does not have any > + * additional capabilities. > + */ > +static struct pmbus_platform_data pli1209bc_plat_data = { > + .flags = PMBUS_NO_CAPABILITY, > +}; > + > +static int pli1209bc_read_word_data(struct i2c_client *client, int page, > + int phase, int reg) > +{ > + int data; > + > + switch (reg) { > + /* PMBUS_READ_POUT uses a direct format with R=0 */ > + case PMBUS_READ_POUT: > + data = pmbus_read_word_data(client, page, phase, reg); > + if (data < 0) > + return data; > + data = sign_extend32(data, 15) * 10; > + return clamp_val(data, -32768, 32767) & 0xffff; > + default: > + return -ENODATA; > + } > +} > + > +static struct pmbus_driver_info pli1209bc_info = { > + .pages = 2, > + .format[PSC_VOLTAGE_IN] = direct, > + .format[PSC_VOLTAGE_OUT] = direct, > + .format[PSC_CURRENT_IN] = direct, > + .format[PSC_CURRENT_OUT] = direct, > + .format[PSC_POWER] = direct, > + .format[PSC_TEMPERATURE] = direct, > + .m[PSC_VOLTAGE_IN] = 1, > + .b[PSC_VOLTAGE_IN] = 0, > + .R[PSC_VOLTAGE_IN] = 1, > + .m[PSC_VOLTAGE_OUT] = 1, > + .b[PSC_VOLTAGE_OUT] = 0, > + .R[PSC_VOLTAGE_OUT] = 1, > + .m[PSC_CURRENT_IN] = 1, > + .b[PSC_CURRENT_IN] = 0, > + .R[PSC_CURRENT_IN] = 3, > + .m[PSC_CURRENT_OUT] = 1, > + .b[PSC_CURRENT_OUT] = 0, > + .R[PSC_CURRENT_OUT] = 2, > + .m[PSC_POWER] = 1, > + .b[PSC_POWER] = 0, > + .R[PSC_POWER] = 1, > + .m[PSC_TEMPERATURE] = 1, > + .b[PSC_TEMPERATURE] = 0, > + .R[PSC_TEMPERATURE] = 0, > + /* > + * Page 0 sums up all attributes except voltage readings. > + * The pli1209 digital supervisor only contains a single BCM, making > + * page 0 redundant. > + */ > + .func[1] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT > + | PMBUS_HAVE_IIN | PMBUS_HAVE_IOUT > + | PMBUS_HAVE_PIN | PMBUS_HAVE_POUT > + | PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP > + | PMBUS_HAVE_STATUS_IOUT | PMBUS_HAVE_STATUS_INPUT, > + .read_word_data = pli1209bc_read_word_data, > +}; > + > +static int pli1209bc_probe(struct i2c_client *client) > +{ > + client->dev.platform_data = &pli1209bc_plat_data; > + return pmbus_do_probe(client, &pli1209bc_info); > +} > + > +static const struct i2c_device_id pli1209bc_id[] = { > + {"pli1209bc", 0}, > + {} > +}; > + > +MODULE_DEVICE_TABLE(i2c, pli1209bc_id); > + > +#ifdef CONFIG_OF > +static const struct of_device_id pli1209bc_of_match[] = { > + { .compatible = "vicor,pli1209bc" }, > + { }, > +}; > +MODULE_DEVICE_TABLE(of, pli1209bc_of_match); > +#endif > + > +static struct i2c_driver pli1209bc_driver = { > + .driver = { > + .name = "pli1209bc", > + .of_match_table = of_match_ptr(pli1209bc_of_match), > + }, > + .probe_new = pli1209bc_probe, > + .id_table = pli1209bc_id, > +}; > + > +module_i2c_driver(pli1209bc_driver); > + > +MODULE_AUTHOR("Marcello Sylvester Bauer <sylv@xxxxxxx>"); > +MODULE_DESCRIPTION("PMBus driver for Vicor PLI1209BC"); > +MODULE_LICENSE("GPL"); > +MODULE_IMPORT_NS(PMBUS);
