On Mon, 2022-02-14 at 09:36 -0800, Guenter Roeck wrote: > On 2/14/22 04:40, Marcello Sylvester Bauer wrote: > > PLI1209BC is a Digital Supervisor from Vicor Corporation. > > > > Signed-off-by: Marcello Sylvester Bauer <sylv@xxxxxxx> > > --- > > Documentation/hwmon/pli1209bc.rst | 73 +++++++++++++++++++ > > drivers/hwmon/pmbus/Kconfig | 9 +++ > > drivers/hwmon/pmbus/Makefile | 1 + > > drivers/hwmon/pmbus/pli1209bc.c | 114 > > ++++++++++++++++++++++++++++++ > > 4 files changed, 197 insertions(+) > > create mode 100644 Documentation/hwmon/pli1209bc.rst > > create mode 100644 drivers/hwmon/pmbus/pli1209bc.c > > > > diff --git a/Documentation/hwmon/pli1209bc.rst > > b/Documentation/hwmon/pli1209bc.rst > > new file mode 100644 > > index 000000000000..a3f686d03cf2 > > --- /dev/null > > +++ b/Documentation/hwmon/pli1209bc.rst > > @@ -0,0 +1,73 @@ > > +Kernel driver pli1209bc > > +======================= > > + > > +Supported chips: > > + > > + * Digital Supervisor PLI1209BC > > + > > + Prefix: 'pli1209bc' > > + > > + Addresses scanned: 0x50 - 0x5F > > + > > + Datasheet: > > https://www.vicorpower.com/documents/datasheets/ds-PLI1209BCxyzz-VICOR.pdf > > + > > +Authors: > > + - Marcello Sylvester Bauer <sylv@xxxxxxx> > > + > > +Description > > +----------- > > + > > +The Vicor PLI1209BC is an isolated digital power system supervisor > > thatprovides > > +a communication interface between a host processor and one Bus > > Converter Module > > +(BCM). The PLI communicates with a system controller via a PMBus > > compatible > > +interface over an isolated UART interface. Through the PLI, the > > host processor > > +can configure, set protection limits, and monitor the BCM. > > + > > +Sysfs entries > > +------------- > > + > > +======================= > > ======================================================== > > +in1_label "vin2" > > +in1_input Input voltage. > > +in1_rated_min Minimum rated input voltage. > > +in1_rated_max Maximum rated input voltage. > > +in1_max Maximum input voltage. > > +in1_max_alarm Input voltage high alarm. > > +in1_crit Critical input voltage. > > +in1_crit_alarm Input voltage critical alarm. > > + > > +in2_label "vout2" > > +in2_input Output voltage. > > +in2_rated_min Minimum rated output voltage. > > +in2_rated_max Maximum rated output voltage. > > +in2_alarm Output voltage alarm > > + > > +curr1_label "iin2" > > +curr1_input Input current. > > +curr1_max Maximum input current. > > +curr1_max_alarm Maximum input current high alarm. > > +curr1_crit Critical input current. > > +curr1_crit_alarm Input current critical alarm. > > + > > +curr2_label "iout2" > > +curr2_input Output current. > > +curr2_crit Critical output current. > > +curr2_crit_alarm Output current critical alarm. > > +curr2_max Maximum output current. > > +curr2_max_alarm Output current high alarm. > > + > > +power1_label "pin2" > > +power1_input Input power. > > +power1_alarm Input power alarm. > > + > > +power2_label "pout2" > > +power2_input Output power. > > +power2_rated_max Maximum rated output power. > > + > > +temp1_input Die temperature. > > +temp1_alarm Die temperature alarm. > > +temp1_max Maximum die temperature. > > +temp1_max_alarm Die temperature high alarm. > > +temp1_crit Critical die temperature. > > +temp1_crit_alarm Die temperature critical alarm. > > +======================= > > ======================================================== > > diff --git a/drivers/hwmon/pmbus/Kconfig > > b/drivers/hwmon/pmbus/Kconfig > > index c96f7b7338bd..831db423bea0 100644 > > --- a/drivers/hwmon/pmbus/Kconfig > > +++ b/drivers/hwmon/pmbus/Kconfig > > @@ -310,6 +310,15 @@ config SENSORS_PIM4328 > > This driver can also be built as a module. If so, the > > module will > > be called pim4328. > > > > +config SENSORS_PLI1209BC > > + tristate "Vicor PLI1209BC" > > + help > > + If you say yes here you get hardware monitoring support > > for Vicor > > + PLI1209BC Digital Supervisor. > > + > > + This driver can also be built as a module. If so, the > > module will > > + be called pli1209bc. > > + > > config SENSORS_PM6764TR > > tristate "ST PM6764TR" > > help > > diff --git a/drivers/hwmon/pmbus/Makefile > > b/drivers/hwmon/pmbus/Makefile > > index e5935f70c9e0..7ce74e3b8552 100644 > > --- a/drivers/hwmon/pmbus/Makefile > > +++ b/drivers/hwmon/pmbus/Makefile > > @@ -34,6 +34,7 @@ obj-$(CONFIG_SENSORS_MP2888) += mp2888.o > > obj-$(CONFIG_SENSORS_MP2975) += mp2975.o > > obj-$(CONFIG_SENSORS_MP5023) += mp5023.o > > obj-$(CONFIG_SENSORS_PM6764TR) += pm6764tr.o > > +obj-$(CONFIG_SENSORS_PLI1209BC) += pli1209bc.o > > obj-$(CONFIG_SENSORS_PXE1610) += pxe1610.o > > obj-$(CONFIG_SENSORS_Q54SJ108A2) += q54sj108a2.o > > obj-$(CONFIG_SENSORS_STPDDC60) += stpddc60.o > > diff --git a/drivers/hwmon/pmbus/pli1209bc.c > > b/drivers/hwmon/pmbus/pli1209bc.c > > new file mode 100644 > > index 000000000000..8a9af2ccc46f > > --- /dev/null > > +++ b/drivers/hwmon/pmbus/pli1209bc.c > > @@ -0,0 +1,114 @@ > > +// SPDX-License-Identifier: GPL-2.0+ > > +/* > > + * Hardware monitoring driver for Vicor PLI1209BC Digital > > Supervisor > > + * > > + * Copyright (c) 2022 9elements GmbH > > + */ > > + > > +#include <linux/i2c.h> > > +#include <linux/module.h> > > +#include <linux/pmbus.h> > > +#include "pmbus.h" > > + > > +/* > > + * The capability command is only supported at page 0. Probing the > > device while > > + * the page register is set to 1 will falsely enable PEC support. > > Disable > > + * capability probing accordingly, since the PLI1209BC does not > > have any > > + * additional capabilities. > > + */ > > +static struct pmbus_platform_data pli1209bc_plat_data = { > > + .flags = PMBUS_NO_CAPABILITY, > > +}; > > + > > +static int pli1209bc_read_word_data(struct i2c_client *client, int > > page, > > + int phase, int reg) > > +{ > > + int data; > > + > > + switch (reg) { > > + /* PMBUS_READ_POUT uses a direct format with R=0 */ > > + case PMBUS_READ_POUT: > > + data = pmbus_read_word_data(client, page, phase, > > reg); > > + if (data < 0) > > + return data; > > + return data * 10; > > We have to be more careful here. While the datasheet doesn't > explicitly > say if the reported value is signed or not, the standard says that > it is supposed to be signed, so let's assume that this is the case. > That means that 'data' is really 16-bit signed value. We have to make > sure that it doesn't over- or underflow when multiplying it, > and that the sign is retained. Something like the following should > do. > > data = sign_extend32(data, 15) * 10; > return clamp_val(data, -32768, 32767) & 0xffff; Being careful makes sense indeed. I guess we should not use definitions in limit.h, since int size is arch specific. I'll take it like this. Thanks, Marcello > > Otherwise the patch looks good. > > Thanks, > Guenter > > > + default: > > + return -ENODATA; > > + } > > +} > > + > > +static struct pmbus_driver_info pli1209bc_info = { > > + .pages = 2, > > + .format[PSC_VOLTAGE_IN] = direct, > > + .format[PSC_VOLTAGE_OUT] = direct, > > + .format[PSC_CURRENT_IN] = direct, > > + .format[PSC_CURRENT_OUT] = direct, > > + .format[PSC_POWER] = direct, > > + .format[PSC_TEMPERATURE] = direct, > > + .m[PSC_VOLTAGE_IN] = 1, > > + .b[PSC_VOLTAGE_IN] = 0, > > + .R[PSC_VOLTAGE_IN] = 1, > > + .m[PSC_VOLTAGE_OUT] = 1, > > + .b[PSC_VOLTAGE_OUT] = 0, > > + .R[PSC_VOLTAGE_OUT] = 1, > > + .m[PSC_CURRENT_IN] = 1, > > + .b[PSC_CURRENT_IN] = 0, > > + .R[PSC_CURRENT_IN] = 3, > > + .m[PSC_CURRENT_OUT] = 1, > > + .b[PSC_CURRENT_OUT] = 0, > > + .R[PSC_CURRENT_OUT] = 2, > > + .m[PSC_POWER] = 1, > > + .b[PSC_POWER] = 0, > > + .R[PSC_POWER] = 1, > > + .m[PSC_TEMPERATURE] = 1, > > + .b[PSC_TEMPERATURE] = 0, > > + .R[PSC_TEMPERATURE] = 0, > > + /* > > + * Page 0 sums up all attributes except voltage readings. > > + * The pli1209 digital supervisor only contains a single > > BCM, making > > + * page 0 redundant. > > + */ > > + .func[1] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT > > + | PMBUS_HAVE_IIN | PMBUS_HAVE_IOUT > > + | PMBUS_HAVE_PIN | PMBUS_HAVE_POUT > > + | PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP > > + | PMBUS_HAVE_STATUS_IOUT | PMBUS_HAVE_STATUS_INPUT, > > + .read_word_data = pli1209bc_read_word_data, > > +}; > > + > > +static int pli1209bc_probe(struct i2c_client *client) > > +{ > > + client->dev.platform_data = &pli1209bc_plat_data; > > + return pmbus_do_probe(client, &pli1209bc_info); > > +} > > + > > +static const struct i2c_device_id pli1209bc_id[] = { > > + {"pli1209bc", 0}, > > + {} > > +}; > > + > > +MODULE_DEVICE_TABLE(i2c, pli1209bc_id); > > + > > +#ifdef CONFIG_OF > > +static const struct of_device_id pli1209bc_of_match[] = { > > + { .compatible = "vicor,pli1209bc" }, > > + { }, > > +}; > > +MODULE_DEVICE_TABLE(of, pli1209bc_of_match); > > +#endif > > + > > +static struct i2c_driver pli1209bc_driver = { > > + .driver = { > > + .name = "pli1209bc", > > + .of_match_table = > > of_match_ptr(pli1209bc_of_match), > > + }, > > + .probe_new = pli1209bc_probe, > > + .id_table = pli1209bc_id, > > +}; > > + > > +module_i2c_driver(pli1209bc_driver); > > + > > +MODULE_AUTHOR("Marcello Sylvester Bauer <sylv@xxxxxxx>"); > > +MODULE_DESCRIPTION("PMBus driver for Vicor PLI1209BC"); > > +MODULE_LICENSE("GPL"); > > +MODULE_IMPORT_NS(PMBUS); >
