Converts hwmon/gpio-fan.txt to YAML
Signed-off-by: Corentin Labbe <clabbe@xxxxxxxxxxxx>
---
I didnt found any clear maintainer and since DT yaml mandates a
maintainer section, I set devicetree@xxxxxxxxxxxxxxx.
.../devicetree/bindings/hwmon/gpio-fan.txt | 41 --------
.../devicetree/bindings/hwmon/gpio-fan.yaml | 96 +++++++++++++++++++
2 files changed, 96 insertions(+), 41 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/hwmon/gpio-fan.txt
create mode 100644 Documentation/devicetree/bindings/hwmon/gpio-fan.yaml
diff --git a/Documentation/devicetree/bindings/hwmon/gpio-fan.txt b/Documentation/devicetree/bindings/hwmon/gpio-fan.txt
deleted file mode 100644
index f4cfa350f6a1..000000000000
--- a/Documentation/devicetree/bindings/hwmon/gpio-fan.txt
+++ /dev/null
@@ -1,41 +0,0 @@
-Bindings for fan connected to GPIO lines
-
-Required properties:
-- compatible : "gpio-fan"
-
-Optional properties:
-- gpios: Specifies the pins that map to bits in the control value,
- ordered MSB-->LSB.
-- gpio-fan,speed-map: A mapping of possible fan RPM speeds and the
- control value that should be set to achieve them. This array
- must have the RPM values in ascending order.
-- alarm-gpios: This pin going active indicates something is wrong with
- the fan, and a udev event will be fired.
-- #cooling-cells: If used as a cooling device, must be <2>
- Also see:
- Documentation/devicetree/bindings/thermal/thermal-cooling-devices.yaml
- min and max states are derived from the speed-map of the fan.
-
-Note: At least one the "gpios" or "alarm-gpios" properties must be set.
-
-Examples:
-
- gpio_fan {
- compatible = "gpio-fan";
- gpios = <&gpio1 14 1
- &gpio1 13 1>;
- gpio-fan,speed-map = <0 0
- 3000 1
- 6000 2>;
- alarm-gpios = <&gpio1 15 1>;
- };
- gpio_fan_cool: gpio_fan {
- compatible = "gpio-fan";
- gpios = <&gpio2 14 1
- &gpio2 13 1>;
- gpio-fan,speed-map = <0 0>,
- <3000 1>,
- <6000 2>;
- alarm-gpios = <&gpio2 15 1>;
- #cooling-cells = <2>; /* min followed by max */
- };
diff --git a/Documentation/devicetree/bindings/hwmon/gpio-fan.yaml b/Documentation/devicetree/bindings/hwmon/gpio-fan.yaml
new file mode 100644
index 000000000000..15bb5efd3cb4
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/gpio-fan.yaml
@@ -0,0 +1,96 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/hwmon/gpio-fan.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Bindings for fan connected to GPIO lines
+
+maintainers:
+ - OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS <devicetree@xxxxxxxxxxxxxxx>
+
+properties:
+ compatible:
+ const: gpio-fan
+
+ gpios:
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ description: Specifies the pins that map to bits in the control value,
+ ordered MSB-->LSB.
+
+ gpio-fan,speed-map:
+ $ref: /schemas/types.yaml#/definitions/uint32-matrix
+ description: A mapping of possible fan RPM speeds and the
+ control value that should be set to achieve them. This array
+ must have the RPM values in ascending order.
+
+ alarm-gpios:
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ description: This pin going active indicates something is wrong with
+ the fan, and a udev event will be fired.
+
+ "#cooling-cells":
+ const: 2
+ description: If used as a cooling device, must be <2>
+ Also see Documentation/devicetree/bindings/thermal/thermal-cooling-devices.yaml
+ min and max states are derived from the speed-map of the fan.
+
+anyOf:
+ - required:
+ - gpios
+ - required:
+ - alarm-gpios
+
+additionalProperties: False
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/clock/cortina,gemini-clock.h>
+ #include <dt-bindings/reset/cortina,gemini-reset.h>
+ #include <dt-bindings/gpio/gpio.h>
+ gpio1: gpio@4d000000 {
+ compatible = "cortina,gemini-gpio", "faraday,ftgpio010";
+ reg = <0x4d000000 0x100>;
+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&syscon GEMINI_RESET_GPIO0>;
+ clocks = <&syscon GEMINI_CLK_APB>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ gpio_fan {
+ compatible = "gpio-fan";
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ gpio-fan,speed-map = <0 0>,
+ <3000 1>,
+ <6000 2>;
+ alarm-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
+ };
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/clock/cortina,gemini-clock.h>
+ #include <dt-bindings/reset/cortina,gemini-reset.h>
+ #include <dt-bindings/gpio/gpio.h>
+ gpio2: gpio@4d000000 {
+ compatible = "cortina,gemini-gpio", "faraday,ftgpio010";
+ reg = <0x4d000000 0x100>;
+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&syscon GEMINI_RESET_GPIO0>;
+ clocks = <&syscon GEMINI_CLK_APB>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ gpio_fan_cool: gpio_fan {
+ compatible = "gpio-fan";
+ gpios = <&gpio2 8 GPIO_ACTIVE_HIGH
+ &gpio2 1 GPIO_ACTIVE_HIGH>;
+ gpio-fan,speed-map = <0 0
+ 3000 1
+ 6000 2>;
+ alarm-gpios = <&gpio2 15 GPIO_ACTIVE_HIGH>;
+ #cooling-cells = <2>; /* min followed by max */
+ };
--
2.34.1
