[PATCH v2 2/3] hwmon: (pmbus) Add documentation for new flags

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add documentation for the new pmbus flags PMBUS_WRITE_PROTECTED,
PMBUS_NO_CAPABILITY and PMBUS_READ_STATUS_AFTER_FAILED_CHECK

Signed-off-by: Erik Rosen <erik.rosen@xxxxxxxxxxxxx>
---
 Documentation/hwmon/pmbus-core.rst | 42 +++++++++++++++++++++++++++---
 1 file changed, 38 insertions(+), 4 deletions(-)

diff --git a/Documentation/hwmon/pmbus-core.rst b/Documentation/hwmon/pmbus-core.rst
index 73e23ab42cc3..102c50e2be3d 100644
--- a/Documentation/hwmon/pmbus-core.rst
+++ b/Documentation/hwmon/pmbus-core.rst
@@ -289,12 +289,22 @@ PMBus driver platform data
 ==========================
 
 PMBus platform data is defined in include/linux/pmbus.h. Platform data
-currently only provides a flag field with a single bit used::
+currently provides a flags field with four bits used::
 
-	#define PMBUS_SKIP_STATUS_CHECK (1 << 0)
+	#define PMBUS_SKIP_STATUS_CHECK			BIT(0)
+
+	#define PMBUS_WRITE_PROTECTED			BIT(1)
+
+	#define PMBUS_NO_CAPABILITY			BIT(2)
+
+	#define PMBUS_READ_STATUS_AFTER_FAILED_CHECK	BIT(3)
 
 	struct pmbus_platform_data {
 		u32 flags;              /* Device specific flags */
+
+		/* regulator support */
+		int num_regulators;
+		struct regulator_init_data *reg_init_data;
 	};
 
 
@@ -302,8 +312,9 @@ Flags
 -----
 
 PMBUS_SKIP_STATUS_CHECK
-	During register detection, skip checking the status register for
-	communication or command errors.
+
+During register detection, skip checking the status register for
+communication or command errors.
 
 Some PMBus chips respond with valid data when trying to read an unsupported
 register. For such chips, checking the status register is mandatory when
@@ -315,3 +326,26 @@ status register must be disabled.
 Some i2c controllers do not support single-byte commands (write commands with
 no data, i2c_smbus_write_byte()). With such controllers, clearing the status
 register is impossible, and the PMBUS_SKIP_STATUS_CHECK flag must be set.
+
+PMBUS_WRITE_PROTECTED
+
+Set if the chip is write protected and write protection is not determined
+by the standard WRITE_PROTECT command.
+
+PMBUS_NO_CAPABILITY
+
+Some PMBus chips don't respond with valid data when reading the CAPABILITY
+register. For such chips, this flag should be set so that the PMBus core
+driver doesn't use CAPABILITY to determine it's behavior.
+
+PMBUS_READ_STATUS_AFTER_FAILED_CHECK
+
+Read the STATUS register after each failed register check.
+
+Some PMBus chips end up in an undefined state when trying to read an
+unsupported register. For such chips, it is necessary to reset the
+chip pmbus controller to a known state after a failed register check.
+This can be done by reading a known register. By setting this flag the
+driver will try to read the STATUS register after each failed
+register check. This read may fail, but it will put the chip into a
+known state.
\ No newline at end of file
-- 
2.20.1




[Index of Archives]     [LM Sensors]     [Linux Sound]     [ALSA Users]     [ALSA Devel]     [Linux Audio Users]     [Linux Media]     [Kernel]     [Gimp]     [Yosemite News]     [Linux Media]

  Powered by Linux