On 4/26/21 3:17 PM, Vadim Pasternak wrote:
> Add support for mp2888 device from Monolithic Power Systems, Inc. (MPS)
> vendor. This is a digital, multi-phase, pulse-width modulation
> controller.
>
> This device supports:
> - One power rail.
> - Programmable Multi-Phase up to 10 Phases.
> - PWM-VID Interface
> - One pages 0 for telemetry.
> - Programmable pins for PMBus Address.
> - Built-In EEPROM to Store Custom Configurations.
> - Can configured VOUT readout in direct or VID format and allows
> setting of different formats on rails 1 and 2. For VID the following
> protocols are available: VR13 mode with 5-mV DAC; VR13 mode with
> 10-mV DAC, IMVP9 mode with 5-mV DAC.
>
> Signed-off-by: Vadim Pasternak <vadimp@xxxxxxxxxx>
> ---
> v2->v3
> Comments pointed out by Guenter:
> - Fix precision for PMBUS_READ_VIN (it requires adding scale for
> PMBUS_VIN_OV_FAULT_LIMIT and PMBUS_VIN_UV_WARN_LIMIT.
> - Fix precision for PMBUS_READ_TEMPERATURE_1 (it requires adding
> scale for PMBUS_OT_WARN_LIMIT).
> - Use DIV_ROUND_CLOSEST_ULL for scaling PMBUS_READ_POUT,
> PMBUS_READ_PIN readouts.
> Notes and fixes from Vadim:
> - READ_IOUT in linear11 does not give write calculation (tested with
> external load), while in direct format readouts are correct.
> - Disable non-configured phases in mp2888_identify_multiphase().
>
> v1->v2:
> Comments pointed out by Guenter:
> - Use standard access for getting PMBUS_OT_WARN_LIMIT,
> PMBUS_VIN_OV_FAULT_LIMIT, PMBUS_VIN_UV_WARN_LIMIT.
> - Use linear11 conversion for PMBUS_READ_VIN, PMBUS_READ_POUT,
> PMBUS_READ_PIN, PMBUS_READ_TEMPERATURE_1 and adjust coefficients.
> - Add reading phases current from the dedicated registers.
> - Add comment for not implemented or implemented not according to the
> spec registers, for which "ENXIO" code is returned.
> - Set PMBUS_HAVE_IOUT" statically.
> Notes from Vadim:
> - READ_IOUT uses direct format, so I did not adjust it like the below
> registers.
> ---
> Documentation/hwmon/mp2888.rst | 111 ++++++++++++
> drivers/hwmon/pmbus/Kconfig | 9 +
> drivers/hwmon/pmbus/Makefile | 1 +
> drivers/hwmon/pmbus/mp2888.c | 387 +++++++++++++++++++++++++++++++++++++++++
> 4 files changed, 508 insertions(+)
> create mode 100644 Documentation/hwmon/mp2888.rst
> create mode 100644 drivers/hwmon/pmbus/mp2888.c
>
> diff --git a/Documentation/hwmon/mp2888.rst b/Documentation/hwmon/mp2888.rst
> new file mode 100644
> index 000000000000..7839a010642a
> --- /dev/null
> +++ b/Documentation/hwmon/mp2888.rst
> @@ -0,0 +1,111 @@
> +.. SPDX-License-Identifier: GPL-2.0
> +
> +Kernel driver mp2888
> +====================
> +
> +Supported chips:
> +
> + * MPS MP12254
> +
> + Prefix: 'mp2888'
> +
> +Author:
> +
> + Vadim Pasternak <vadimp@xxxxxxxxxx>
> +
> +Description
> +-----------
> +
> +This driver implements support for Monolithic Power Systems, Inc. (MPS)
> +vendor dual-loop, digital, multi-phase controller MP2888.
> +
> +This device: supports:
> +
> +- One power rail.
> +- Programmable Multi-Phase up to 10 Phases.
> +- PWM-VID Interface
> +- One pages 0 for telemetry.
> +- Programmable pins for PMBus Address.
> +- Built-In EEPROM to Store Custom Configurations.
> +
> +Device complaint with:
> +
> +- PMBus rev 1.3 interface.
> +
> +Device supports direct format for reading output current, output voltage,
> +input and output power and temperature.
> +Device supports linear format for reading input voltage and input power.
> +
> +The driver provides the next attributes for the current:
> +
> +- for current out input and maximum alarm;
> +- for phase current: input and label.
> +
> +The driver exports the following attributes via the 'sysfs' files, where:
> +
> +- 'n' is number of configured phases (from 1 to 10);
> +- index 1 for "iout";
> +- indexes 2 ... 1 + n for phases.
> +
> +**curr1_alarm**
> +
> +**curr[1-{1+n}]_input**
> +
> +**curr[1-{1+n}]_label**
> +
> +The driver provides the next attributes for the voltage:
> +
> +- for voltage in: input, low and high critical thresholds, low and high
> + critical alarms;
> +- for voltage out: input and high alarm;
> +
> +The driver exports the following attributes via the 'sysfs' files, where
> +
> +**in1_crit**
> +
> +**in1_crit_alarm**
> +
> +**in1_input**
> +
> +**in1_label**
> +
> +**in1_min**
> +
> +**in1_min_alarm**
> +
> +**in2_alarm**
> +
> +**in2_input**
> +
> +**in2_label**
> +
> +The driver provides the next attributes for the power:
> +
> +- for power in alarm and input.
> +- for power out: cap, cap alarm an input.
> +
> +The driver exports the following attributes via the 'sysfs' files, where
> +- indexes 1 for "pin";
> +- indexes 2 for "pout";
> +
> +**power1_alarm**
> +
> +**power1_input**
> +
> +**power1_label**
> +
> +**power2_cap**
> +
> +**power2_cap_alarm**
> +
> +**power2_input**
> +
> +**power2_label**
> +
> +The driver provides the next attributes for the temperature:
> +
> +**temp1_input**
> +
> +**temp1_max**
> +
> +**temp1_max_alarm**
> diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
> index 32d2fc850621..a57571928b31 100644
> --- a/drivers/hwmon/pmbus/Kconfig
> +++ b/drivers/hwmon/pmbus/Kconfig
> @@ -211,6 +211,15 @@ config SENSORS_MAX8688
> This driver can also be built as a module. If so, the module will
> be called max8688.
>
> +config SENSORS_MP2888
> + tristate "MPS MP2888"
> + help
> + If you say yes here you get hardware monitoring support for MPS
> + MP2888 Digital, Multi-Phase, Pulse-Width Modulation Controller.
> +
> + This driver can also be built as a module. If so, the module will
> + be called mp2888.
> +
> config SENSORS_MP2975
> tristate "MPS MP2975"
> help
> diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
> index 6a4ba0fdc1db..a6d7352621ca 100644
> --- a/drivers/hwmon/pmbus/Makefile
> +++ b/drivers/hwmon/pmbus/Makefile
> @@ -24,6 +24,7 @@ obj-$(CONFIG_SENSORS_MAX20751) += max20751.o
> obj-$(CONFIG_SENSORS_MAX31785) += max31785.o
> obj-$(CONFIG_SENSORS_MAX34440) += max34440.o
> obj-$(CONFIG_SENSORS_MAX8688) += max8688.o
> +obj-$(CONFIG_SENSORS_MP2888) += mp2888.o
> obj-$(CONFIG_SENSORS_MP2975) += mp2975.o
> obj-$(CONFIG_SENSORS_PM6764TR) += pm6764tr.o
> obj-$(CONFIG_SENSORS_PXE1610) += pxe1610.o
> diff --git a/drivers/hwmon/pmbus/mp2888.c b/drivers/hwmon/pmbus/mp2888.c
> new file mode 100644
> index 000000000000..4b90f0e8cbd7
> --- /dev/null
> +++ b/drivers/hwmon/pmbus/mp2888.c
> @@ -0,0 +1,387 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * Hardware monitoring driver for MPS Multi-phase Digital VR Controllers
> + *
> + * Copyright (C) 2020 Nvidia Technologies Ltd.
> + */
> +
> +#include <linux/err.h>
> +#include <linux/i2c.h>
> +#include <linux/init.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include "pmbus.h"
> +
> +/* Vendor specific registers. */
> +#define MP2888_MFR_SYS_CONFIG 0x44
> +#define MP2888_MFR_READ_CS1_2 0x73
> +#define MP2888_MFR_READ_CS3_4 0x74
> +#define MP2888_MFR_READ_CS5_6 0x75
> +#define MP2888_MFR_READ_CS7_8 0x76
> +#define MP2888_MFR_READ_CS9_10 0x77
> +#define MP2888_MFR_VR_CONFIG1 0xe1
> +
> +#define MP2888_TOTAL_CURRENT_RESOLUTION BIT(3)
> +#define MP2888_PHASE_CURRENT_RESOLUTION BIT(4)
> +#define MP2888_DRMOS_KCS GENMASK(2, 0)
> +#define MP2888_VIN_LIMIT_UNIT 8
> +#define MP2888_TEMP_UNIT 10
> +#define MP2888_VIN_MANTISSA 32
> +#define MP2888_MAX_PHASE 10
> +
> +struct mp2888_data {
> + struct pmbus_driver_info info;
> + int total_curr_resolution;
> + int phase_curr_resolution;
> + int curr_sense_gain;
> +};
> +
> +#define to_mp2888_data(x) container_of(x, struct mp2888_data, info)
> +
> +static int mp2888_read_byte_data(struct i2c_client *client, int page, int reg)
> +{
> + switch (reg) {
> + case PMBUS_VOUT_MODE:
> + /* Enforce VOUT direct format. */
> + return PB_VOUT_MODE_DIRECT;
> + default:
> + return -ENODATA;
> + }
> +}
> +
> +/* Convert linear sensor values to milli- or micro-units depending on sensor type. */
> +static s64 mp2888_reg2data_linear11(int data, enum pmbus_sensor_classes class)
> +{
> + s16 exponent;
> + s32 mantissa;
> + s64 val;
> +
> + exponent = ((s16)data) >> 11;
> + mantissa = ((s16)((data & 0x7ff) << 5)) >> 5;
> + val = mantissa;
> +
> + /* Scale result to micro-units for power sensors. */
> + if (class == PSC_POWER)
> + val = val * 1000LL;
> +
> + if (exponent >= 0)
> + val <<= exponent;
> + else
> + val >>= -exponent;
> +
> + return val;
> +}
> +
> +static int
> +mp2888_current_sense_gain_and_resolution_get(struct i2c_client *client, struct mp2888_data *data)
> +{
> + int ret;
> +
> + /*
> + * Obtain DrMOS current sense gain of power stage from the register
> + * , bits 0-2. The value is selected as below:
> + * 00b - 5µA/A, 01b - 8.5µA/A, 10b - 9.7µA/A, 11b - 10µA/A. Other
> + * values are reserved.
> + */
> + ret = i2c_smbus_read_word_data(client, MP2888_MFR_SYS_CONFIG);
> + if (ret < 0)
> + return ret;
> +
> + switch (ret & MP2888_DRMOS_KCS) {
> + case 0:
> + data->curr_sense_gain = 85;
> + break;
> + case 1:
> + data->curr_sense_gain = 97;
> + break;
> + case 2:
> + data->curr_sense_gain = 100;
> + break;
> + case 3:
> + data->curr_sense_gain = 50;
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + /*
> + * Obtain resolution selector for total and phase current report and protection.
> + * 0: original resolution; 1: half resolution (in such case phase current value should
> + * be doubled.
> + */
> + data->total_curr_resolution = (ret & MP2888_TOTAL_CURRENT_RESOLUTION) >> 3;
> + data->phase_curr_resolution = (ret & MP2888_PHASE_CURRENT_RESOLUTION) >> 4;
> +
> + return 0;
> +}
> +
> +static int
> +mp2888_read_phase(struct i2c_client *client, struct mp2888_data *data, int page, int phase, u8 reg)
> +{
> + int ret;
> +
> + ret = pmbus_read_word_data(client, page, phase, reg);
> + if (ret < 0)
> + return ret;
> +
> + if (!((phase + 1) % 2))
> + ret >>= 8;
> + ret &= 0xff;
> +
> + /*
> + * Output value is calculated as: (READ_CSx / 80 – 1.23) / (Kcs * Rcs)
> + * where:
> + * - Kcs is the DrMOS current sense gain of power stage, which is obtained from the
> + * register MP2888_MFR_VR_CONFIG1, bits 13-12 with the following selection of DrMOS
> + * (data->curr_sense_gain):
> + * 00b - 5µA/A, 01b - 8.5µA/A, 10b - 9.7µA/A, 11b - 10µA/A.
> + * - Rcs is the internal phase current sense resistor. This parameter depends on hardware
> + * assembly. By default it is set to 1kΩ. In case of different assembly, user should
> + * scale this parameter by dividing it by Rcs.
> + * If phase current resolution bit is set to 1, READ_CSx value should be doubled.
> + * Note, that current phase sensing, providing by the device is not accurate. This is
> + * because sampling of current occurrence of bit weight has a big deviation, especially for
> + * light load.
> + */
> + if (data->phase_curr_resolution)
> + ret *= 2;
> + return DIV_ROUND_CLOSEST(ret * 100 - 9800, data->curr_sense_gain);
> +}
> +
> +static int
> +mp2888_read_phases(struct i2c_client *client, struct mp2888_data *data, int page, int phase)
> +{
> + int ret;
> +
> + switch (phase) {
> + case 0 ... 1:
> + ret = mp2888_read_phase(client, data, page, phase, MP2888_MFR_READ_CS1_2);
> + break;
> + case 2 ... 3:
> + ret = mp2888_read_phase(client, data, page, phase, MP2888_MFR_READ_CS3_4);
> + break;
> + case 4 ... 5:
> + ret = mp2888_read_phase(client, data, page, phase, MP2888_MFR_READ_CS5_6);
> + break;
> + case 6 ... 7:
> + ret = mp2888_read_phase(client, data, page, phase, MP2888_MFR_READ_CS7_8);
> + break;
> + case 8 ... 9:
> + ret = mp2888_read_phase(client, data, page, phase, MP2888_MFR_READ_CS9_10);
> + break;
> + default:
> + return -ENODATA;
> + }
> + return ret;
> +}
> +
> +static int mp2888_read_word_data(struct i2c_client *client, int page, int phase, int reg)
> +{
> + const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
> + struct mp2888_data *data = to_mp2888_data(info);
> + s64 val;
> + int ret;
> +
> + switch (reg) {
> + case PMBUS_READ_VIN:
> + ret = pmbus_read_word_data(client, page, phase, reg);
> + if (ret <= 0)
> + return ret;
> +
> + /*
> + * READ_VIN register has unused bits 15:10 with fixed value 111011b. Clear these
> + * bits and scale with coefficient 0.03125 by using mantissa 32.
> + */
> + ret = (ret & GENMASK(9, 0));
> + break;
> + case PMBUS_VIN_OV_FAULT_LIMIT:
> + case PMBUS_VIN_UV_WARN_LIMIT:
> + ret = pmbus_read_word_data(client, page, phase, reg);
> + if (ret <= 0)
> + return ret;
> +
> + val = mp2888_reg2data_linear11(ret, PSC_VOLTAGE_IN);
> + ret = val * MP2888_VIN_MANTISSA;
> + break;
Unless I am missing something, this is linear11 with, for some reason, bit 10
erroneously set for PMBUS_READ_VIN. That means that setting the format for
PSC_VOLTAGE_IN and clearing bit 10 for PMBUS_READ_VIN should work
without local conversion. Am I missing something ?
> + case PMBUS_OT_WARN_LIMIT:
> + ret = pmbus_read_word_data(client, page, phase, reg);
> + if (ret < 0)
> + return ret;
> + ret *= MP2888_TEMP_UNIT;
Explanation would be useful: chip reports limits in degrees C, but the actual
temperature in 10th of degrees C. This is needed to match the two.
> + break;
> + case PMBUS_READ_IOUT:
> + if (phase != 0xff)
> + return mp2888_read_phases(client, data, page, phase);
> +
> + ret = pmbus_read_word_data(client, page, phase, reg);
> + if (ret < 0)
> + return ret;
> + /*
> + * READ_IOUT register has unused bits 15:12 with fixed value 1110b. Clear these
> + * bits and scale with total current resolution. Data is provided in direct format.
> + */
> + ret &= GENMASK(11, 0);
> + ret = data->total_curr_resolution ? DIV_ROUND_CLOSEST(ret, 2) :
> + DIV_ROUND_CLOSEST(ret, 4);
I don't think this is a good idea: It unnecessarily reduces the resolution
(which is bad enough already). The format for output current is already set
to direct with a mantissa of 1. It might make sense to adjust the mantissa
to always report the correct current. Specifically, if current resolution is
set to 1, the value here should be multiplied, not divided.
> + break;
> + case PMBUS_READ_POUT:
> + case PMBUS_READ_PIN:
> + ret = pmbus_read_word_data(client, page, phase, reg);
> + if (ret < 0)
> + return ret;
> + val = mp2888_reg2data_linear11(ret, PSC_POWER);
This call seems pretty pointless: The exponent bits are always 0,
and we know that the resolution is either 0.5W or 1W.
Conversion to micro-watt should be handled by the PMBus core.
> + ret = data->total_curr_resolution ? val : DIV_ROUND_CLOSEST_ULL(val, 2);
Same as above: Any adjustment should be a multiplication, not a divide operation,
to avoid resolution loss.
> + break;
> + /*
> + * The below registers are not implemented by device or implemented not according to the
> + * spec. Skip all of them to avoid exposing non-relevant inputs to sysfs.
> + */
> + case PMBUS_OT_FAULT_LIMIT:
> + case PMBUS_UT_WARN_LIMIT:
> + case PMBUS_UT_FAULT_LIMIT:
> + case PMBUS_VIN_UV_FAULT_LIMIT:
> + case PMBUS_VOUT_UV_WARN_LIMIT:
> + case PMBUS_VOUT_OV_WARN_LIMIT:
> + case PMBUS_VOUT_UV_FAULT_LIMIT:
> + case PMBUS_VOUT_OV_FAULT_LIMIT:
> + case PMBUS_VIN_OV_WARN_LIMIT:
> + case PMBUS_IOUT_OC_LV_FAULT_LIMIT:
> + case PMBUS_IOUT_OC_WARN_LIMIT:
Datasheet says this is a 10-bit value with a scale of 1A or 2A depending on
the current resolution.
> + case PMBUS_IOUT_OC_FAULT_LIMIT:
> + case PMBUS_IOUT_UC_FAULT_LIMIT:
> + case PMBUS_POUT_OP_FAULT_LIMIT:
> + case PMBUS_POUT_OP_WARN_LIMIT:
Datasheet: 10-bit value with 1W/LSB or 2W/LSB depending on current resolution.
Unless there is reqason to believe that the datasheet is wrong,
those should be supported. If the datasheet is wrong it should be explained.
> + case PMBUS_PIN_OP_WARN_LIMIT:
> + case PMBUS_MFR_VIN_MIN:
> + case PMBUS_MFR_VIN_MAX:
> + case PMBUS_MFR_VOUT_MAX:
> + case PMBUS_MFR_IIN_MAX:
> + case PMBUS_MFR_IOUT_MAX:
> + case PMBUS_MFR_PIN_MAX:
> + case PMBUS_MFR_POUT_MAX:
> + case PMBUS_MFR_MAX_TEMP_1:
> + return -ENXIO;
> + default:
> + return -ENODATA;
> + }
> +
> + return ret;
> +}
> +
> +static int
> +mp2888_identify_multiphase(struct i2c_client *client, struct mp2888_data *data,
> + struct pmbus_driver_info *info)
> +{
> + int i, ret;
> +
> + ret = i2c_smbus_write_byte_data(client, PMBUS_PAGE, 0);
> + if (ret < 0)
> + return ret;
> +
> + /* Identify multiphase number - could be from 1 to 10. */
> + ret = i2c_smbus_read_word_data(client, MP2888_MFR_VR_CONFIG1);
> + if (ret <= 0)
> + return ret;
> +
> + info->phases[0] = ret & GENMASK(3, 0);
> +
> + /*
> + * The device provides a total of 10 PWM pins, and can be configured to different phase
> + * count applications for rail.
> + */
> + if (info->phases[0] > MP2888_MAX_PHASE)
> + return -EINVAL;
> +
> + /* Disable non-configured phases. */
> + for (i = info->phases[0]; i < MP2888_MAX_PHASE; i++)
> + info->pfunc[i] = 0;
> +
> + return 0;
> +}
> +
> +static struct pmbus_driver_info mp2888_info = {
> + .pages = 1,
> + .format[PSC_VOLTAGE_IN] = direct,
> + .format[PSC_VOLTAGE_OUT] = direct,
> + .format[PSC_TEMPERATURE] = direct,
> + .format[PSC_CURRENT_IN] = linear,
> + .format[PSC_CURRENT_OUT] = direct,
> + .format[PSC_POWER] = direct,
> + .m[PSC_VOLTAGE_IN] = MP2888_VIN_MANTISSA,
> + .m[PSC_TEMPERATURE] = 1,
> + .R[PSC_TEMPERATURE] = 1,
> + .m[PSC_VOLTAGE_OUT] = 1,
> + .R[PSC_VOLTAGE_OUT] = 3,
> + .m[PSC_CURRENT_OUT] = 1,
> + .m[PSC_POWER] = 1,
> + .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT | PMBUS_HAVE_IOUT |
> + PMBUS_HAVE_STATUS_IOUT | PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP |
> + PMBUS_HAVE_POUT | PMBUS_HAVE_PIN | PMBUS_HAVE_STATUS_INPUT |
> + PMBUS_PHASE_VIRTUAL,
> + .pfunc[0] = PMBUS_HAVE_IOUT,
> + .pfunc[1] = PMBUS_HAVE_IOUT,
> + .pfunc[2] = PMBUS_HAVE_IOUT,
> + .pfunc[3] = PMBUS_HAVE_IOUT,
> + .pfunc[4] = PMBUS_HAVE_IOUT,
> + .pfunc[5] = PMBUS_HAVE_IOUT,
> + .pfunc[6] = PMBUS_HAVE_IOUT,
> + .pfunc[7] = PMBUS_HAVE_IOUT,
> + .pfunc[8] = PMBUS_HAVE_IOUT,
> + .pfunc[9] = PMBUS_HAVE_IOUT,
> + .read_byte_data = mp2888_read_byte_data,
> + .read_word_data = mp2888_read_word_data,
I don't see a write function here. Did you try setting limits ?
Given the adjustments needed for reading limits, I don't think this will work.
Thanks,
Guenter
> +};
> +
> +static int mp2888_probe(struct i2c_client *client)
> +{
> + struct pmbus_driver_info *info;
> + struct mp2888_data *data;
> + int ret;
> +
> + data = devm_kzalloc(&client->dev, sizeof(struct mp2888_data), GFP_KERNEL);
> + if (!data)
> + return -ENOMEM;
> +
> + memcpy(&data->info, &mp2888_info, sizeof(*info));
> + info = &data->info;
> +
> + /* Identify multiphase configuration. */
> + ret = mp2888_identify_multiphase(client, data, info);
> + if (ret)
> + return ret;
> +
> + /* Obtain current sense gain of power stage and current resolution. */
> + ret = mp2888_current_sense_gain_and_resolution_get(client, data);
> + if (ret)
> + return ret;
> +
> + return pmbus_do_probe(client, info);
> +}
> +
> +static const struct i2c_device_id mp2888_id[] = {
> + {"mp2888", 0},
> + {}
> +};
> +
> +MODULE_DEVICE_TABLE(i2c, mp2888_id);
> +
> +static const struct of_device_id __maybe_unused mp2888_of_match[] = {
> + {.compatible = "mps,mp2888"},
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, mp2888_of_match);
> +
> +static struct i2c_driver mp2888_driver = {
> + .driver = {
> + .name = "mp2888",
> + .of_match_table = of_match_ptr(mp2888_of_match),
> + },
> + .probe_new = mp2888_probe,
> + .id_table = mp2888_id,
> +};
> +
> +module_i2c_driver(mp2888_driver);
> +
> +MODULE_AUTHOR("Vadim Pasternak <vadimp@xxxxxxxxxx>");
> +MODULE_DESCRIPTION("PMBus driver for MPS MP2888 device");
> +MODULE_LICENSE("GPL");
>
