On Tue, Oct 13, 2020 at 02:14:44PM +0200, Mauro Carvalho Chehab wrote:
> .../Documentation/hwmon/mp2975.rst:25: WARNING: Unexpected indentation.
> .../Documentation/hwmon/mp2975.rst:27: WARNING: Block quote ends without a blank line; unexpected unindent.
> .../Documentation/hwmon/mp2975.rst:69: WARNING: Unexpected indentation.
> .../Documentation/hwmon/mp2975.rst:70: WARNING: Block quote ends without a blank line; unexpected unindent.
> .../Documentation/hwmon/mp2975.rst:72: WARNING: Bullet list ends without a blank line; unexpected unindent.
> .../Documentation/hwmon/mp2975.rst: WARNING: document isn't included in any toctree
>
> List blocks should have blank lines before and after them,
> in order to be properly parsed.
>
> Fixes: 4beb7a028e9f ("hwmon: (pmbus) Add support for MPS Multi-phase mp2975 controller")
> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@xxxxxxxxxx>
Acked-by: Guenter Roeck <linux@xxxxxxxxxxxx>
> ---
> Documentation/hwmon/index.rst | 1 +
> Documentation/hwmon/mp2975.rst | 14 +++++++++++++-
> 2 files changed, 14 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
> index e6b91ab12978..b797db738225 100644
> --- a/Documentation/hwmon/index.rst
> +++ b/Documentation/hwmon/index.rst
> @@ -132,6 +132,7 @@ Hardware Monitoring Kernel Drivers
> mcp3021
> menf21bmc
> mlxreg-fan
> + mp2975
> nct6683
> nct6775
> nct7802
> diff --git a/Documentation/hwmon/mp2975.rst b/Documentation/hwmon/mp2975.rst
> index 5b0609c62f48..81d816b71490 100644
> --- a/Documentation/hwmon/mp2975.rst
> +++ b/Documentation/hwmon/mp2975.rst
> @@ -20,6 +20,7 @@ This driver implements support for Monolithic Power Systems, Inc. (MPS)
> vendor dual-loop, digital, multi-phase controller MP2975.
>
> This device:
> +
> - Supports up to two power rail.
> - Provides 8 pulse-width modulations (PWMs), and can be configured up
> to 8-phase operation for rail 1 and up to 4-phase operation for rail
> @@ -32,10 +33,12 @@ This device:
> 10-mV DAC, IMVP9 mode with 5-mV DAC.
>
> Device supports:
> +
> - SVID interface.
> - AVSBus interface.
>
> Device complaint with:
> +
> - PMBus rev 1.3 interface.
>
> Device supports direct format for reading output current, output voltage,
> @@ -45,11 +48,14 @@ Device supports VID and direct formats for reading output voltage.
> The below VID modes are supported: VR12, VR13, IMVP9.
>
> The driver provides the next attributes for the current:
> +
> - for current in: input, maximum alarm;
> - for current out input, maximum alarm and highest values;
> - for phase current: input and label.
> -attributes.
> + attributes.
> +
> The driver exports the following attributes via the 'sysfs' files, where
> +
> - 'n' is number of telemetry pages (from 1 to 2);
> - 'k' is number of configured phases (from 1 to 8);
> - indexes 1, 1*n for "iin";
> @@ -65,11 +71,14 @@ The driver exports the following attributes via the 'sysfs' files, where
> **curr[1-{2n+k}]_label**
>
> The driver provides the next attributes for the voltage:
> +
> - for voltage in: input, high critical threshold, high critical alarm, all only
> from page 0;
> - for voltage out: input, low and high critical thresholds, low and high
> critical alarms, from pages 0 and 1;
> +
> The driver exports the following attributes via the 'sysfs' files, where
> +
> - 'n' is number of telemetry pages (from 1 to 2);
> - indexes 1 for "iin";
> - indexes n+1, n+2 for "vout";
> @@ -87,9 +96,12 @@ The driver exports the following attributes via the 'sysfs' files, where
> **in[2-{n+1}1_lcrit_alarm**
>
> The driver provides the next attributes for the power:
> +
> - for power in alarm and input.
> - for power out: highest and input.
> +
> The driver exports the following attributes via the 'sysfs' files, where
> +
> - 'n' is number of telemetry pages (from 1 to 2);
> - indexes 1 for "pin";
> - indexes n+1, n+2 for "pout";
> --
> 2.26.2
>
