Re: [PATCH v6 07/13] gpio: add support for the sl28cpld GPIO controller

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sun, Jul 26, 2020 at 01:18:28AM +0200, Michael Walle wrote:
> Add support for the GPIO controller of the sl28 board management
> controller. This driver is part of a multi-function device.
> 
> A controller has 8 lines. There are three different flavors:
> full-featured GPIO with interrupt support, input-only and output-only.

FWIW,
Reviewed-by: Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx>

> Signed-off-by: Michael Walle <michael@xxxxxxxx>
> Reviewed-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
> ---
> Changes since v5:
>  - added "select REGMAP_IRQ"
> 
> Changes since v4:
>  - update copyright year
>  - remove #include <linux/of_device.h>, suggested by Andy.
>  - use device_get_match_data(), suggested by Andy.
>  - drop the irq_support variable, instead call _init_irq() directly,
>    suggested by Andy.
>  - also move the irq code a bit around to make it look nicer
>  - drop "struct sl28cpld_gpio". We don't need to actually store the
>    irq_chip and irq_chip_data, everything is device resource managed.
>  - use 100 chars line limit, suggested by Andy.
>  - remove the platform device table
>  - don't use KBUID_MODNAME
> 
> Changes since v3:
>  - see cover letter
> 
>  drivers/gpio/Kconfig         |  12 +++
>  drivers/gpio/Makefile        |   1 +
>  drivers/gpio/gpio-sl28cpld.c | 161 +++++++++++++++++++++++++++++++++++
>  3 files changed, 174 insertions(+)
>  create mode 100644 drivers/gpio/gpio-sl28cpld.c
> 
> diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
> index 8030fd91a3cc..f6a547b76432 100644
> --- a/drivers/gpio/Kconfig
> +++ b/drivers/gpio/Kconfig
> @@ -1223,6 +1223,18 @@ config GPIO_RC5T583
>  	  This driver provides the support for driving/reading the gpio pins
>  	  of RC5T583 device through standard gpio library.
>  
> +config GPIO_SL28CPLD
> +	tristate "Kontron sl28cpld GPIO support"
> +	select MFD_SIMPLE_MFD_I2C
> +	select GPIO_REGMAP
> +	select GPIOLIB_IRQCHIP
> +	select REGMAP_IRQ
> +	help
> +	  This enables support for the GPIOs found on the Kontron sl28 CPLD.
> +
> +	  This driver can also be built as a module. If so, the module will be
> +	  called gpio-sl28cpld.
> +
>  config GPIO_STMPE
>  	bool "STMPE GPIOs"
>  	depends on MFD_STMPE
> diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
> index 4f9abff4f2dc..c3a4e7c94a91 100644
> --- a/drivers/gpio/Makefile
> +++ b/drivers/gpio/Makefile
> @@ -132,6 +132,7 @@ obj-$(CONFIG_GPIO_SCH311X)		+= gpio-sch311x.o
>  obj-$(CONFIG_GPIO_SCH)			+= gpio-sch.o
>  obj-$(CONFIG_GPIO_SIFIVE)		+= gpio-sifive.o
>  obj-$(CONFIG_GPIO_SIOX)			+= gpio-siox.o
> +obj-$(CONFIG_GPIO_SL28CPLD)		+= gpio-sl28cpld.o
>  obj-$(CONFIG_GPIO_SODAVILLE)		+= gpio-sodaville.o
>  obj-$(CONFIG_GPIO_SPEAR_SPICS)		+= gpio-spear-spics.o
>  obj-$(CONFIG_GPIO_SPRD)			+= gpio-sprd.o
> diff --git a/drivers/gpio/gpio-sl28cpld.c b/drivers/gpio/gpio-sl28cpld.c
> new file mode 100644
> index 000000000000..889b8f5622c2
> --- /dev/null
> +++ b/drivers/gpio/gpio-sl28cpld.c
> @@ -0,0 +1,161 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * sl28cpld GPIO driver
> + *
> + * Copyright 2020 Michael Walle <michael@xxxxxxxx>
> + */
> +
> +#include <linux/device.h>
> +#include <linux/gpio/driver.h>
> +#include <linux/gpio/regmap.h>
> +#include <linux/interrupt.h>
> +#include <linux/kernel.h>
> +#include <linux/mod_devicetable.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +
> +/* GPIO flavor */
> +#define GPIO_REG_DIR	0x00
> +#define GPIO_REG_OUT	0x01
> +#define GPIO_REG_IN	0x02
> +#define GPIO_REG_IE	0x03
> +#define GPIO_REG_IP	0x04
> +
> +/* input-only flavor */
> +#define GPI_REG_IN	0x00
> +
> +/* output-only flavor */
> +#define GPO_REG_OUT	0x00
> +
> +enum sl28cpld_gpio_type {
> +	SL28CPLD_GPIO = 1,
> +	SL28CPLD_GPI,
> +	SL28CPLD_GPO,
> +};
> +
> +static const struct regmap_irq sl28cpld_gpio_irqs[] = {
> +	REGMAP_IRQ_REG_LINE(0, 8),
> +	REGMAP_IRQ_REG_LINE(1, 8),
> +	REGMAP_IRQ_REG_LINE(2, 8),
> +	REGMAP_IRQ_REG_LINE(3, 8),
> +	REGMAP_IRQ_REG_LINE(4, 8),
> +	REGMAP_IRQ_REG_LINE(5, 8),
> +	REGMAP_IRQ_REG_LINE(6, 8),
> +	REGMAP_IRQ_REG_LINE(7, 8),
> +};
> +
> +static int sl28cpld_gpio_irq_init(struct platform_device *pdev,
> +				  unsigned int base,
> +				  struct gpio_regmap_config *config)
> +{
> +	struct regmap_irq_chip_data *irq_data;
> +	struct regmap_irq_chip *irq_chip;
> +	struct device *dev = &pdev->dev;
> +	int irq, ret;
> +
> +	if (!device_property_read_bool(dev, "interrupt-controller"))
> +		return 0;
> +
> +	irq = platform_get_irq(pdev, 0);
> +	if (irq < 0)
> +		return irq;
> +
> +	irq_chip = devm_kzalloc(dev, sizeof(*irq_chip), GFP_KERNEL);
> +	if (!irq_chip)
> +		return -ENOMEM;
> +
> +	irq_chip->name = "sl28cpld-gpio-irq",
> +	irq_chip->irqs = sl28cpld_gpio_irqs;
> +	irq_chip->num_irqs = ARRAY_SIZE(sl28cpld_gpio_irqs);
> +	irq_chip->num_regs = 1;
> +	irq_chip->status_base = base + GPIO_REG_IP;
> +	irq_chip->mask_base = base + GPIO_REG_IE;
> +	irq_chip->mask_invert = true,
> +	irq_chip->ack_base = base + GPIO_REG_IP;
> +
> +	ret = devm_regmap_add_irq_chip_fwnode(dev, dev_fwnode(dev),
> +					      config->regmap, irq,
> +					      IRQF_SHARED | IRQF_ONESHOT,
> +					      0, irq_chip, &irq_data);
> +	if (ret)
> +		return ret;
> +
> +	config->irq_domain = regmap_irq_get_domain(irq_data);
> +
> +	return 0;
> +}
> +
> +static int sl28cpld_gpio_probe(struct platform_device *pdev)
> +{
> +	struct gpio_regmap_config config = {0};
> +	enum sl28cpld_gpio_type type;
> +	struct regmap *regmap;
> +	u32 base;
> +	int ret;
> +
> +	if (!pdev->dev.parent)
> +		return -ENODEV;
> +
> +	type = (uintptr_t)device_get_match_data(&pdev->dev);
> +	if (!type)
> +		return -ENODEV;
> +
> +	ret = device_property_read_u32(&pdev->dev, "reg", &base);
> +	if (ret)
> +		return -EINVAL;
> +
> +	regmap = dev_get_regmap(pdev->dev.parent, NULL);
> +	if (!regmap)
> +		return -ENODEV;
> +
> +	config.regmap = regmap;
> +	config.parent = &pdev->dev;
> +	config.ngpio = 8;
> +
> +	switch (type) {
> +	case SL28CPLD_GPIO:
> +		config.reg_dat_base = base + GPIO_REG_IN;
> +		config.reg_set_base = base + GPIO_REG_OUT;
> +		/* reg_dir_out_base might be zero */
> +		config.reg_dir_out_base = GPIO_REGMAP_ADDR(base + GPIO_REG_DIR);
> +
> +		/* This type supports interrupts */
> +		ret = sl28cpld_gpio_irq_init(pdev, base, &config);
> +		if (ret)
> +			return ret;
> +		break;
> +	case SL28CPLD_GPO:
> +		config.reg_set_base = base + GPO_REG_OUT;
> +		break;
> +	case SL28CPLD_GPI:
> +		config.reg_dat_base = base + GPI_REG_IN;
> +		break;
> +	default:
> +		dev_err(&pdev->dev, "unknown type %d\n", type);
> +		return -ENODEV;
> +	}
> +
> +	return PTR_ERR_OR_ZERO(devm_gpio_regmap_register(&pdev->dev, &config));
> +}
> +
> +static const struct of_device_id sl28cpld_gpio_of_match[] = {
> +	{ .compatible = "kontron,sl28cpld-gpio", .data = (void *)SL28CPLD_GPIO },
> +	{ .compatible = "kontron,sl28cpld-gpi", .data = (void *)SL28CPLD_GPI },
> +	{ .compatible = "kontron,sl28cpld-gpo", .data = (void *)SL28CPLD_GPO },
> +	{}
> +};
> +MODULE_DEVICE_TABLE(of, sl28cpld_gpio_of_match);
> +
> +static struct platform_driver sl28cpld_gpio_driver = {
> +	.probe = sl28cpld_gpio_probe,
> +	.driver = {
> +		.name = "sl28cpld-gpio",
> +		.of_match_table = sl28cpld_gpio_of_match,
> +	},
> +};
> +module_platform_driver(sl28cpld_gpio_driver);
> +
> +MODULE_DESCRIPTION("sl28cpld GPIO Driver");
> +MODULE_AUTHOR("Michael Walle <michael@xxxxxxxx>");
> +MODULE_LICENSE("GPL");
> -- 
> 2.20.1
> 

-- 
With Best Regards,
Andy Shevchenko





[Index of Archives]     [LM Sensors]     [Linux Sound]     [ALSA Users]     [ALSA Devel]     [Linux Audio Users]     [Linux Media]     [Kernel]     [Gimp]     [Yosemite News]     [Linux Media]

  Powered by Linux