On Thu, Apr 23, 2020 at 07:45:32PM +0200, Michael Walle wrote: > This patch adds core support for the board management controller found > on the SMARC-sAL28 board. It consists of the following functions: > - watchdog > - GPIO controller > - PWM controller > - fan sensor > - interrupt controller > > At the moment, this controller is used on the Kontron SMARC-sAL28 board. > > Please note that the MFD driver is defined as bool in the Kconfig > because the next patch will add interrupt support. > > Signed-off-by: Michael Walle <michael@xxxxxxxx> > --- > drivers/mfd/Kconfig | 19 +++++ > drivers/mfd/Makefile | 2 + > drivers/mfd/sl28cpld.c | 153 +++++++++++++++++++++++++++++++++++++++++ > 3 files changed, 174 insertions(+) > create mode 100644 drivers/mfd/sl28cpld.c > > diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig > index 0a59249198d3..be0c8d93c526 100644 > --- a/drivers/mfd/Kconfig > +++ b/drivers/mfd/Kconfig > @@ -2060,5 +2060,24 @@ config SGI_MFD_IOC3 > If you have an SGI Origin, Octane, or a PCI IOC3 card, > then say Y. Otherwise say N. > > +config MFD_SL28CPLD > + bool "Kontron sl28 core driver" > + depends on I2C=y > + depends on OF > + select REGMAP_I2C > + select MFD_CORE > + help > + This option enables support for the board management controller > + found on the Kontron sl28 CPLD. You have to select individual > + functions, such as watchdog, GPIO, etc, under the corresponding menus > + in order to enable them. > + > + Currently supported boards are: > + > + Kontron SMARC-sAL28 > + > + To compile this driver as a module, choose M here: the module will be > + called sl28cpld. > + > endmenu > endif > diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile > index f935d10cbf0f..9bc38863b9c7 100644 > --- a/drivers/mfd/Makefile > +++ b/drivers/mfd/Makefile > @@ -259,3 +259,5 @@ obj-$(CONFIG_MFD_ROHM_BD718XX) += rohm-bd718x7.o > obj-$(CONFIG_MFD_STMFX) += stmfx.o > > obj-$(CONFIG_SGI_MFD_IOC3) += ioc3.o > + > +obj-$(CONFIG_MFD_SL28CPLD) += sl28cpld.o > diff --git a/drivers/mfd/sl28cpld.c b/drivers/mfd/sl28cpld.c > new file mode 100644 > index 000000000000..1e5860cc7ffc > --- /dev/null > +++ b/drivers/mfd/sl28cpld.c > @@ -0,0 +1,153 @@ > +// SPDX-License-Identifier: GPL-2.0-only > +/* > + * MFD core for the sl28cpld. > + * > + * Copyright 2019 Kontron Europe GmbH > + */ > + > +#include <linux/i2c.h> > +#include <linux/interrupt.h> > +#include <linux/kernel.h> > +#include <linux/mfd/core.h> > +#include <linux/module.h> > +#include <linux/of_platform.h> > +#include <linux/regmap.h> > + > +#define SL28CPLD_VERSION 0x03 > +#define SL28CPLD_WATCHDOG_BASE 0x04 > +#define SL28CPLD_HWMON_FAN_BASE 0x0b > +#define SL28CPLD_PWM0_BASE 0x0c > +#define SL28CPLD_PWM1_BASE 0x0e > +#define SL28CPLD_GPIO0_BASE 0x10 > +#define SL28CPLD_GPIO1_BASE 0x15 > +#define SL28CPLD_GPO_BASE 0x1a > +#define SL28CPLD_GPI_BASE 0x1b > +#define SL28CPLD_INTC_BASE 0x1c If you want to use 'reg' in the binding, these are the numbers you should be using rather than making up numbering! However, I still don't think you need any child nodes. All the data in the DT binding is right here in the driver already. There's no advantage to putting child nodes in DT, because this driver still has to be updated if you add more nodes. Rob
