Add documentation for 'xdpe122' devices. Signed-off-by: Vadim Pasternak <vadimp@xxxxxxxxxxxx> --- Documentation/hwmon/xdpe12284.rst | 101 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 101 insertions(+) create mode 100644 Documentation/hwmon/xdpe12284.rst diff --git a/Documentation/hwmon/xdpe12284.rst b/Documentation/hwmon/xdpe12284.rst new file mode 100644 index 000000000000..6b7ae98cc536 --- /dev/null +++ b/Documentation/hwmon/xdpe12284.rst @@ -0,0 +1,101 @@ +.. SPDX-License-Identifier: GPL-2.0 + +Kernel driver xdpe122 +===================== + +Supported chips: + + * Infineon XDPE12254 + + Prefix: 'xdpe12254' + + * Infineon XDPE12284 + + Prefix: 'xdpe12284' + +Authors: + + Vadim Pasternak <vadimp@xxxxxxxxxxxx> + +Description +----------- + +This driver implements support for Infineon Multi-phase XDPE122 family +dual loop voltage regulators. +The family includes XDPE12284 and XDPE12254 devices. +The devices from this family complaint with: +- Intel VR13 and VR13HC rev 1.3, IMVP8 rev 1.2 and IMPVP9 rev 1.3 DC-DC + converter specification. +- Intel SVID rev 1.9. protocol. +- PMBus rev 1.3 interface. + +Devices support linear format for reading input voltage, input and output current, +input and output power and temperature. +Device supports VID format for reading output voltage. The below modes are +supported: +- VR12.0 mode, 5-mV DAC - 0x01. +- VR12.5 mode, 10-mV DAC - 0x02. +- IMVP9 mode, 5-mV DAC - 0x03. +- AMD mode 6.25mV - 0x10. + +Devices support two pages for telemetry. + +The driver provides for current: input, maximum and critical thresholds +and maximum and critical alarms. Critical thresholds and critical alarm are +supported only for current output. +The driver exports the following attributes for via the sysfs files, where +indexes 1, 2 are for "iin" and 3, 4 for "iout": + +**curr[3-4]_crit** + +**curr[3-4]_crit_alarm** + +**curr[1-4]_input** + +**curr[1-4]_label** + +**curr[1-4]_max** + +**curr[1-4]_max_alarm** + +The driver provides for voltage: input, critical and low critical thresholds +and critical and low critical alarms. +The driver exports the following attributes for via the sysfs files, where +indexes 1, 2 are for "vin" and 3, 4 for "vout": + +**in[1-4]_crit** + +**in[1-4_crit_alarm** + +**in[1-4]_input** + +**in[1-4_label** + +**in[1-4]_lcrit** + +**in[1-41_lcrit_alarm** + +The driver provides for power: input and alarms. Power alarm is supported only +for power input. +The driver exports the following attributes for via the sysfs files, where +indexes 1, 2 are for "pin" and 3, 4 for "pout": + +**power[1-2]_alarm** + +**power[1-4]_input** + +**power[1-4]_label** + +The driver provides for temperature: input, maximum and critical thresholds +and maximum and critical alarms. +The driver exports the following attributes for via the sysfs files: + +**temp[1-2]_crit** + +**temp[1-2]_crit_alarm** + +**temp[1-2]_input** + +**temp[1-2]_max** + +**temp[1-2]_max_alarm** -- 2.11.0
