> -----Original Message-----
> From: Guenter Roeck <groeck7@xxxxxxxxx> On Behalf Of Guenter Roeck
> Sent: Sunday, January 05, 2020 6:26 PM
> To: Vadim Pasternak <vadimp@xxxxxxxxxxxx>; robh+dt@xxxxxxxxxx;
> vijaykhemka@xxxxxx
> Cc: linux-hwmon@xxxxxxxxxxxxxxx; devicetree@xxxxxxxxxxxxxxx
> Subject: Re: [RFC PATCH hwmon-next v1 2/5] hwmon: (pmbus/core) Add support
> for Intel IMVP9 specification
>
> On 1/5/20 2:58 AM, Vadim Pasternak wrote:
> > Extend "vrm_version" with support for Intel IMVP9 specification.
> >
> > Signed-off-by: Vadim Pasternak <vadimp@xxxxxxxxxxxx>
> > ---
> > drivers/hwmon/pmbus/pmbus.h | 2 +-
> > drivers/hwmon/pmbus/pmbus_core.c | 4 ++++
> > 2 files changed, 5 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/hwmon/pmbus/pmbus.h b/drivers/hwmon/pmbus/pmbus.h
> > index 2bdebd0ea9c1..c6b2401f1c6c 100644
> > --- a/drivers/hwmon/pmbus/pmbus.h
> > +++ b/drivers/hwmon/pmbus/pmbus.h
> > @@ -377,7 +377,7 @@ enum pmbus_sensor_classes {
> > #define PMBUS_PAGE_VIRTUAL BIT(31)
> >
> > enum pmbus_data_format { linear = 0, direct, vid }; -enum
> > vrm_version { vr11 = 0, vr12, vr13 };
> > +enum vrm_version { vr11 = 0, vr12, vr13, imvp9 };
> >
> > struct pmbus_driver_info {
> > int pages; /* Total number of pages */
> > diff --git a/drivers/hwmon/pmbus/pmbus_core.c
> > b/drivers/hwmon/pmbus/pmbus_core.c
> > index 98226e84b351..a9b7b555cf6e 100644
> > --- a/drivers/hwmon/pmbus/pmbus_core.c
> > +++ b/drivers/hwmon/pmbus/pmbus_core.c
> > @@ -709,6 +709,10 @@ static long pmbus_reg2data_vid(struct pmbus_data
> *data,
> > if (val >= 0x01)
> > rv = 500 + (val - 1) * 10;
> > break;
> > + case imvp9:
> > + if (val >= 0x01)
> > + rv = 200 + (val - 1) * 10;
> > + break;
>
> There is also Intel VR14, and there is some indication that it is identical to imvp9.
> If that is the case, I would prefer to use existing terminology.
> Unfortunately, Intel is a bit close-lipped about both. If you have access to
> documentation, can you check ?
Hi Guenter,
It's really tricky to find some clear Intel doc on for that.
I checked it with ours and Infineon HW guys.
IMVP9 has a different VID table than VR13HC/VR14.
For v14 we can use the same formula as we are using for vr13.
IMVP9 is different because it has a different voltage range.
The 5mV VID table of VR14 supports a voltage range from
0.25V to 1.52V.
The 10mV VID table of VR14 supports a voltage range from
0.5V t0 3.04V.
The IMVP9 VID table also has a 10mV step, but the voltage range
is from 0.2 to 2.74V.
Thanks,
Vadim.
>
> Thanks,
> Guenter
>
> > }
> > return rv;
> > }
> >
