On Sat, Nov 02, 2019 at 08:31:15AM -0700, Guenter Roeck wrote: > On Tue, Oct 29, 2019 at 11:20:54AM -0700, rentao.bupt@xxxxxxxxx wrote: > > From: Tao Ren <rentao.bupt@xxxxxxxxx> > > > > Add documentation for bel-pfe pmbus driver which supports BEL PFE1100 and > > PFE3000 power supplies. > > > > Signed-off-by: Tao Ren <rentao.bupt@xxxxxxxxx> > > Applied after adding bel-pfe to index.rst. > > Thanks, > Guenter Thank you Guenter. I didn't know index.rst needs to be updated; will do it for my future doc patches. Cheers, Tao > > --- > > No change in v2. > > > > Documentation/hwmon/bel-pfe.rst | 112 ++++++++++++++++++++++++++++++++ > > 1 file changed, 112 insertions(+) > > create mode 100644 Documentation/hwmon/bel-pfe.rst > > > > diff --git a/Documentation/hwmon/bel-pfe.rst b/Documentation/hwmon/bel-pfe.rst > > new file mode 100644 > > index 000000000000..4b4a7d67854c > > --- /dev/null > > +++ b/Documentation/hwmon/bel-pfe.rst > > @@ -0,0 +1,112 @@ > > +Kernel driver bel-pfe > > +====================== > > + > > +Supported chips: > > + > > + * BEL PFE1100 > > + > > + Prefixes: 'pfe1100' > > + > > + Addresses scanned: - > > + > > + Datasheet: https://www.belfuse.com/resources/datasheets/powersolutions/ds-bps-pfe1100-12-054xa.pdf > > + > > + * BEL PFE3000 > > + > > + Prefixes: 'pfe3000' > > + > > + Addresses scanned: - > > + > > + Datasheet: https://www.belfuse.com/resources/datasheets/powersolutions/ds-bps-pfe3000-series.pdf > > + > > +Author: Tao Ren <rentao.bupt@xxxxxxxxx> > > + > > + > > +Description > > +----------- > > + > > +This driver supports hardware monitoring for below power supply devices > > +which support PMBus Protocol: > > + > > + * BEL PFE1100 > > + > > + 1100 Watt AC to DC power-factor-corrected (PFC) power supply. > > + PMBus Communication Manual is not publicly available. > > + > > + * BEL PFE3000 > > + > > + 3000 Watt AC/DC power-factor-corrected (PFC) and DC-DC power supply. > > + PMBus Communication Manual is not publicly available. > > + > > +The driver is a client driver to the core PMBus driver. Please see > > +Documentation/hwmon/pmbus.rst for details on PMBus client drivers. > > + > > + > > +Usage Notes > > +----------- > > + > > +This driver does not auto-detect devices. You will have to instantiate the > > +devices explicitly. Please see Documentation/i2c/instantiating-devices.rst for > > +details. > > + > > +Example: the following will load the driver for an PFE3000 at address 0x20 > > +on I2C bus #1:: > > + > > + $ modprobe bel-pfe > > + $ echo pfe3000 0x20 > /sys/bus/i2c/devices/i2c-1/new_device > > + > > + > > +Platform data support > > +--------------------- > > + > > +The driver supports standard PMBus driver platform data. > > + > > + > > +Sysfs entries > > +------------- > > + > > +======================= ======================================================= > > +curr1_label "iin" > > +curr1_input Measured input current > > +curr1_max Input current max value > > +curr1_max_alarm Input current max alarm > > + > > +curr[2-3]_label "iout[1-2]" > > +curr[2-3]_input Measured output current > > +curr[2-3]_max Output current max value > > +curr[2-3]_max_alarm Output current max alarm > > + > > +fan[1-2]_input Fan 1 and 2 speed in RPM > > +fan1_target Set fan speed reference for both fans > > + > > +in1_label "vin" > > +in1_input Measured input voltage > > +in1_crit Input voltage critical max value > > +in1_crit_alarm Input voltage critical max alarm > > +in1_lcrit Input voltage critical min value > > +in1_lcrit_alarm Input voltage critical min alarm > > +in1_max Input voltage max value > > +in1_max_alarm Input voltage max alarm > > + > > +in2_label "vcap" > > +in2_input Hold up capacitor voltage > > + > > +in[3-8]_label "vout[1-3,5-7]" > > +in[3-8]_input Measured output voltage > > +in[3-4]_alarm vout[1-2] output voltage alarm > > + > > +power[1-2]_label "pin[1-2]" > > +power[1-2]_input Measured input power > > +power[1-2]_alarm Input power high alarm > > + > > +power[3-4]_label "pout[1-2]" > > +power[3-4]_input Measured output power > > + > > +temp[1-3]_input Measured temperature > > +temp[1-3]_alarm Temperature alarm > > +======================= ======================================================= > > + > > +.. note:: > > + > > + - curr3, fan2, vout[2-7], vcap, pin2, pout2 and temp3 attributes only > > + exist for PFE3000.
