Document the LTC2947 device devicetree bindings. Signed-off-by: Nuno Sá <nuno.sa@xxxxxxxxxx> --- Changes in v2: * Add license identifier; * Fix the uint32-array properties; * Set maximum at the same indent as allOf in adi,accumulation-deadband-microamp; * Set enum at the same indent as allOf in adi,gpio-out-pol; * Use spi instead of spi0 on the example; Changes in v3: * Nothing changed. .../bindings/hwmon/adi,ltc2947.yaml | 104 ++++++++++++++++++ MAINTAINERS | 1 + 2 files changed, 105 insertions(+) create mode 100644 Documentation/devicetree/bindings/hwmon/adi,ltc2947.yaml diff --git a/Documentation/devicetree/bindings/hwmon/adi,ltc2947.yaml b/Documentation/devicetree/bindings/hwmon/adi,ltc2947.yaml new file mode 100644 index 000000000000..ae04903f34bf --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/adi,ltc2947.yaml @@ -0,0 +1,104 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/bindings/hwmon/adi,ltc2947.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices LTC2947 high precision power and energy monitor + +maintainers: + - Nuno Sá <nuno.sa@xxxxxxxxxx> + +description: | + Analog Devices LTC2947 high precision power and energy monitor over SPI or I2C. + + https://www.analog.com/media/en/technical-documentation/data-sheets/LTC2947.pdf + +properties: + compatible: + enum: + - adi,ltc2947 + + reg: + maxItems: 1 + + clocks: + description: + The LTC2947 uses either a trimmed internal oscillator or an external clock + as the time base for determining the integration period to represent time, + charge and energy. When an external clock is used, this property must be + set accordingly. + maxItems: 1 + + adi,accumulator-ctl-pol: + description: + This property controls the polarity of current that is accumulated to + calculate charge and energy so that, they can be only accumulated for + positive current for example. Since there are two sets of registers for + the accumulated values, this entry can also have two items which sets + energy1/charge1 and energy2/charger2 respectively. Check table 12 of the + datasheet for more information on the supported options. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + - minItems: 2 + maxItems: 2 + items: + enum: [0, 1, 2, 3] + default: 0 + + adi,accumulation-deadband-microamp: + description: + This property controls the Accumulation Dead band which allows to set the + level of current below which no accumulation takes place. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 255 + default: 0 + + adi,gpio-out-pol: + description: + This property controls the GPIO polarity. Setting it to one makes the GPIO + active high, setting it to zero makets it active low. When this property + is present, the GPIO is automatically configured as output and set to + control a fan as a function of measured temperature. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + default: 0 + + adi,gpio-in-accum: + description: + When set, this property sets the GPIO as input. It is then used to control + the accumulation of charge, energy and time. This function can be + enabled/configured separately for each of the two sets of accumulation + registers. Check table 13 of the datasheet for more information on the + supported options. This property cannot be used together with + adi,gpio-out-pol. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + - minItems: 2 + maxItems: 2 + items: + enum: [0, 1, 2] + default: 0 + +required: + - compatible + - reg + + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + ltc2947_spi: ltc2947@0 { + compatible = "adi,ltc2947"; + reg = <0>; + /* accumulation takes place always for energ1/charge1. */ + /* accumulation only on positive current for energy2/charge2. */ + adi,accumulator-ctl-pol = <0 1>; + }; + }; +... diff --git a/MAINTAINERS b/MAINTAINERS index 318332b6a411..e2ba1a182052 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -9638,6 +9638,7 @@ F: drivers/hwmon/ltc2947-core.c F: drivers/hwmon/ltc2947-spi.c F: drivers/hwmon/ltc2947-i2c.c F: drivers/hwmon/ltc2947.h +F: Documentation/devicetree/bindings/hwmon/adi,ltc2947.yaml LTC4306 I2C MULTIPLEXER DRIVER M: Michael Hennerich <michael.hennerich@xxxxxxxxxx> -- 2.23.0
