On Wed, 2018-11-07 at 15:31 -0600, Bjorn Helgaas wrote: > On Wed, Nov 07, 2018 at 11:15:37AM -0800, Srinivas Pandruvada wrote: > > On Tue, 2018-11-06 at 17:20 -0600, Bjorn Helgaas wrote: > > > [+cc Sumeet, Srinivas for INT3401 questions below] > > > [Beginning of thread: > > > > > > > https://lore.kernel.org/linux-pci/20181102181055.130531-1-brian.woods@xxxxxxx/ > > > ] > > > > > > On Tue, Nov 06, 2018 at 11:00:59PM +0100, Borislav Petkov wrote: > > > > On Tue, Nov 06, 2018 at 03:42:56PM -0600, Bjorn Helgaas wrote: > > > > > This isn't some complicated new device where the programming > > > > > model changed on the new CPU. This is a thermometer that was > > > > > already supported. ACPI provides plenty of functionality > > > > > that > > > > > could be used to support this generically, e.g., see > > > > > drivers/acpi/thermal.c, > > > > > drivers/thermal/int340x_thermal/processor_thermal_device.c, > > > > > etc. > > > > > > > > Ok, you say ACPI but how do you envision practically doing > > > > that? > > > > I mean, this is used by old boxes too - ever since K8. So how > > > > do > > > > we go and add ACPI functionality to old boxes? > > > > > > > > Or do you mean it should simply be converted to do > > > > pci_register_driver() with a struct pci_driver pointer which > > > > has > > > > all those PCI device IDs in a table? I'm looking at the last > > > > example > > > > drivers/thermal/int340x_thermal/processor_thermal_device.c you > > > > gave above. > > > > > > No, there would be no need to change anything for boxes already > > > in > > > the field. But for *new* systems, you could make devices or > > > thermal zones in the ACPI namespace (they might even already be > > > there for use by Windows). > > > > > > drivers/thermal/int340x_thermal/processor_thermal_device.c claims > > > either INT3401 ACPI devices or listed PCI devices. > > > > To enumerate a driver to get processor temperature and get power > > properties, we have two methods: > > - The older Atom processors valleyview and Baytrail had no PCI > > device > > for the processor thermal management. There was INT3401 ACPI device > > to > > handle this. > > > > - The newer processors for core and Atom, has a dedicate PCI device > > and > > there is no INT3401 ACPI device anymore. > > This is really interesting because it's completely the reverse of > what > I would have expected. > > You use INT3401 on the *older* processors, where int3401_add() is > called for any platform devices with INT3401 PNP ID: > > int3401_add(plat_dev) # platform/ACPI .probe > proc_thermal_add(dev) > adev = ACPI_COMPANION(dev) > int340x_thermal_zone_add(adev) > thermal_zone_device_register() > > The sensors are read in this path, where thermal_zone_get_temp() is > the generic thermal entry point: > > thermal_zone_get_temp() > tz->ops->get_temp() > int340x_thermal_get_zone_temp() # ops.get_temp > acpi_evaluate_integer(..., "_TMP", ...) > > The above works for any platform that supplies the INT3401 device > because the _TMP method that actually reads the sensor is supplied by > the platform firmware. > > On *newer* processors, you apparently use this path: > > proc_thermal_pci_probe(pci_dev) # PCI .probe > pci_enable_device(pci_dev) > proc_thermal_add(dev) > adev = ACPI_COMPANION(dev) > int340x_thermal_zone_add(adev) > thermal_zone_device_register() > > Except for enabling the PCI device and a BSW_THERMAL hack, this is > exactly the *SAME*: you add a thermal zone for the ACPI device and > read the sensor using ACPI _TMP methods. > > But now you have to add new PCI IDs (Skylake, Broxton, CannonLake, > CoffeeLake, GeminiLake, etc) for every new platform. This seems like > a regression, not an improvement. What am I missing? Path of activation via both devices is same. Both will call proc_thermal_add(). There is no INT3401 on any newer atom or core platforms, so you can't enumerate on this device. We don't control what ACPI device is present on a system. It depends on what the other non-Linux OS is using. Also the PCI ACPI companion device doesn't have to supply a _TMP method. The INT3401 is a special device which must have _TMP otherwise firmware validation will fail. Yes, if there is INT3401 on all platforms we don't need PCI enumeration just for temperature and trips. But this PCI device brings in lots of other features which are still in works. Not sure about the context of discussion here. Are you suggesting some core changes where we don't have to add PCI ids like Skylake etc. ? Thanks, Srinivas > > > Since OEM systems will have different power properties and thermal > > trips, there is a companion ACPI device, which provides PPCC and > > thermal trips and optionally output from another temperature sensor > > from the default on processor cores. > > Bjorn
