From: Christopher Bostic <cbostic@xxxxxxxxxxxxxxxxxx> Add a struct gpio_chip and define some methods so that this device's I/O can be accessed via /sys/class/gpio. Signed-off-by: Christopher Bostic <cbostic@xxxxxxxxxxxxxxxxxx> Signed-off-by: Andrew Jeffery <andrew@xxxxxxxx> Signed-off-by: Eddie James <eajames@xxxxxxxxxxxxxxxxxx> --- drivers/hwmon/pmbus/ucd9000.c | 201 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 201 insertions(+) diff --git a/drivers/hwmon/pmbus/ucd9000.c b/drivers/hwmon/pmbus/ucd9000.c index b74dbec..023fb9e 100644 --- a/drivers/hwmon/pmbus/ucd9000.c +++ b/drivers/hwmon/pmbus/ucd9000.c @@ -27,6 +27,7 @@ #include <linux/slab.h> #include <linux/i2c.h> #include <linux/pmbus.h> +#include <linux/gpio.h> #include "pmbus.h" enum chips { ucd9000, ucd90120, ucd90124, ucd90160, ucd9090, ucd90910 }; @@ -35,8 +36,18 @@ #define UCD9000_NUM_PAGES 0xd6 #define UCD9000_FAN_CONFIG_INDEX 0xe7 #define UCD9000_FAN_CONFIG 0xe8 +#define UCD9000_GPIO_SELECT 0xfa +#define UCD9000_GPIO_CONFIG 0xfb #define UCD9000_DEVICE_ID 0xfd +/* GPIO CONFIG bits */ +#define UCD9000_GPIO_CONFIG_ENABLE BIT(0) +#define UCD9000_GPIO_CONFIG_OUT_ENABLE BIT(1) +#define UCD9000_GPIO_CONFIG_OUT_VALUE BIT(2) +#define UCD9000_GPIO_CONFIG_STATUS BIT(3) +#define UCD9000_GPIO_INPUT 0 +#define UCD9000_GPIO_OUTPUT 1 + #define UCD9000_MON_TYPE(x) (((x) >> 5) & 0x07) #define UCD9000_MON_PAGE(x) ((x) & 0x0f) @@ -47,9 +58,15 @@ #define UCD9000_NUM_FAN 4 +#define UCD9000_GPIO_NAME_LEN 16 +#define UCD9090_NUM_GPIOS 23 +#define UCD901XX_NUM_GPIOS 26 +#define UCD90910_NUM_GPIOS 26 + struct ucd9000_data { u8 fan_data[UCD9000_NUM_FAN][I2C_SMBUS_BLOCK_MAX]; struct pmbus_driver_info info; + struct gpio_chip gpio; }; #define to_ucd9000_data(_info) container_of(_info, struct ucd9000_data, info) @@ -149,6 +166,146 @@ static int ucd9000_read_byte_data(struct i2c_client *client, int page, int reg) }; MODULE_DEVICE_TABLE(of, ucd9000_of_match); +static int ucd9000_gpio_read_config(struct i2c_client *client, + unsigned int offset) +{ + int ret; + + /* No page set required */ + ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_SELECT, offset); + if (ret < 0) + return ret; + + return i2c_smbus_read_byte_data(client, UCD9000_GPIO_CONFIG); +} + +static int ucd9000_gpio_get(struct gpio_chip *gc, unsigned int offset) +{ + struct i2c_client *client = gpiochip_get_data(gc); + int ret; + + ret = ucd9000_gpio_read_config(client, offset); + if (ret < 0) + return ret; + + return !!(ret & UCD9000_GPIO_CONFIG_STATUS); +} + +static void ucd9000_gpio_set(struct gpio_chip *gc, unsigned int offset, + int value) +{ + struct i2c_client *client = gpiochip_get_data(gc); + int ret; + + ret = ucd9000_gpio_read_config(client, offset); + if (ret < 0) { + dev_dbg(&client->dev, "failed to read GPIO %d config: %d\n", + offset, ret); + return; + } + + if (value) { + if (ret & UCD9000_GPIO_CONFIG_STATUS) + return; + + ret |= UCD9000_GPIO_CONFIG_STATUS; + } else { + if (!(ret & UCD9000_GPIO_CONFIG_STATUS)) + return; + + ret &= ~UCD9000_GPIO_CONFIG_STATUS; + } + + ret |= UCD9000_GPIO_CONFIG_ENABLE; + + /* Page set not required */ + ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG, ret); + if (ret < 0) { + dev_dbg(&client->dev, "Failed to write GPIO %d config: %d\n", + offset, ret); + return; + } + + ret &= ~UCD9000_GPIO_CONFIG_ENABLE; + + ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG, ret); + if (ret < 0) + dev_dbg(&client->dev, "Failed to write GPIO %d config: %d\n", + offset, ret); +} + +static int ucd9000_gpio_get_direction(struct gpio_chip *gc, + unsigned int offset) +{ + struct i2c_client *client = gpiochip_get_data(gc); + int ret; + + ret = ucd9000_gpio_read_config(client, offset); + if (ret < 0) + return ret; + + return !(ret & UCD9000_GPIO_CONFIG_OUT_ENABLE); +} + +static int ucd9000_gpio_set_direction(struct gpio_chip *gc, + unsigned int offset, bool direction_out, + int requested_out) +{ + struct i2c_client *client = gpiochip_get_data(gc); + int ret, config, out_val; + + ret = ucd9000_gpio_read_config(client, offset); + if (ret < 0) + return ret; + + if (direction_out) { + out_val = requested_out ? UCD9000_GPIO_CONFIG_OUT_VALUE : 0; + + if (ret & UCD9000_GPIO_CONFIG_OUT_ENABLE) { + if ((ret & UCD9000_GPIO_CONFIG_OUT_VALUE) == out_val) + return 0; + } else { + ret |= UCD9000_GPIO_CONFIG_OUT_ENABLE; + } + + if (out_val) + ret |= UCD9000_GPIO_CONFIG_OUT_VALUE; + else + ret &= ~UCD9000_GPIO_CONFIG_OUT_VALUE; + + } else { + if (!(ret & UCD9000_GPIO_CONFIG_OUT_ENABLE)) + return 0; + + ret &= ~UCD9000_GPIO_CONFIG_OUT_ENABLE; + } + + ret |= UCD9000_GPIO_CONFIG_ENABLE; + config = ret; + + /* Page set not required */ + ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG, config); + if (ret < 0) + return ret; + + config &= ~UCD9000_GPIO_CONFIG_ENABLE; + + return i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG, config); +} + +static int ucd9000_gpio_direction_input(struct gpio_chip *gc, + unsigned int offset) +{ + return ucd9000_gpio_set_direction(gc, offset, UCD9000_GPIO_INPUT, 0); +} + +static int ucd9000_gpio_direction_output(struct gpio_chip *gc, + unsigned int offset, int val) +{ + return ucd9000_gpio_set_direction(gc, offset, UCD9000_GPIO_OUTPUT, + val); +} + static int ucd9000_probe(struct i2c_client *client, const struct i2c_device_id *id) { @@ -263,6 +420,50 @@ static int ucd9000_probe(struct i2c_client *client, | PMBUS_HAVE_FAN34 | PMBUS_HAVE_STATUS_FAN34; } + /* + * Note: + * + * Pinmux support has not been added to the new gpio_chip. + * This support should be added when possible given the mux + * behavior of these IO devices. + */ + data->gpio.label = (const char *)&client->name; + data->gpio.get_direction = ucd9000_gpio_get_direction; + data->gpio.direction_input = ucd9000_gpio_direction_input; + data->gpio.direction_output = ucd9000_gpio_direction_output; + data->gpio.get = ucd9000_gpio_get; + data->gpio.set = ucd9000_gpio_set; + data->gpio.can_sleep = 1; + data->gpio.base = -1; + + switch (mid->driver_data) { + case ucd9090: + data->gpio.ngpio = UCD9090_NUM_GPIOS; + break; + case ucd90120: + case ucd90124: + case ucd90160: + data->gpio.ngpio = UCD901XX_NUM_GPIOS; + break; + case ucd90910: + data->gpio.ngpio = UCD90910_NUM_GPIOS; + break; + default: + break; + } + + data->gpio.parent = &client->dev; + data->gpio.owner = THIS_MODULE; + data->gpio.of_node = client->dev.of_node; + + if (data->gpio.ngpio) { + ret = devm_gpiochip_add_data(&client->dev, &data->gpio, + client); + if (ret) + dev_warn(&client->dev, "Could not add gpiochip: %d\n", + ret); + } + return pmbus_do_probe(client, mid, info); } -- 1.8.3.1 -- To unsubscribe from this list: send the line "unsubscribe linux-hwmon" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html