Guenter,
On Thu, Nov 17, 2016 at 4:18 PM, Guenter Roeck <linux@xxxxxxxxxxxx> wrote:
>
> On Thu, Nov 17, 2016 at 02:08:41PM -0600, Jared Bents wrote:
> > On Wed, Nov 16, 2016 at 4:51 PM, Guenter Roeck <linux@xxxxxxxxxxxx> wrote:
> > > On Wed, Nov 16, 2016 at 04:23:53PM -0600, Matt Weber wrote:
> > >> From: Jared Bents <jared.bents@xxxxxxxxxxxxxxxxxxx>
> > >>
> > >> Converts the unsigned temperature values from the i2c read
> > >> to be sign extended as defined in the datasheet so that
> > >> negative temperatures are properly read.
> > >>
> > >> Signed-off-by: Jared Bents <jared.bents@xxxxxxxxxxxxxxxxxxx>
> > >> Signed-off-by: Matt Weber <matthew.weber@xxxxxxxxxxxxxxxxxxx>
> > >> ---
> > >> drivers/hwmon/amc6821.c | 2 +-
> > >> 1 file changed, 1 insertion(+), 1 deletion(-)
> > >>
> > >> diff --git a/drivers/hwmon/amc6821.c b/drivers/hwmon/amc6821.c
> > >> index 12e851a..d7368f7 100644
> > >> --- a/drivers/hwmon/amc6821.c
> > >> +++ b/drivers/hwmon/amc6821.c
> > >> @@ -188,7 +188,7 @@ static struct amc6821_data *amc6821_update_device(struct device *dev)
> > >> !data->valid) {
> > >>
> > >> for (i = 0; i < TEMP_IDX_LEN; i++)
> > >> - data->temp[i] = i2c_smbus_read_byte_data(client,
> > >> + data->temp[i] = (int8_t) i2c_smbus_read_byte_data(client,
> > >
> > > How does that fix anything ? The only difference is that errors reported from
> > > i2c_smbus_read_byte_data() are now capped off and stored as 0xff and no longer
> > > as negative numbers. I don't see how a value of 0xff read from the chip would
> > > now be reported as -1 degrees C; it should be reported as 255 degrees C as it
> > > was all along. What am I missing here ?
> > >
> > > A real fix would be to actually check for errors either here or in the show
> > > function (temp[] < 0 indicates a transfer error), and to use sign_extend()
> > > to convert the 8-bit reading to a signed value.
> > >
> > > Guenter
> > >
> >
> > As stated in the patch note, the amc6821 uses signed numbers for the
> > temperature values. 0xff is -1 Deg C and 0x80 is -128 Deg C via the
> > temperature range table in the amc6821 datasheet. This change does
> > not break any error checking when reading the temperature over the i2c
> > bus in this driver as this driver does not do any error checking for
> > the temperature reads to begin with. There are error checks in the
> > driver but they are for some i2c writes and a few i2c reads for
> > configuration settings. None of those error checks are affected.
> > Without this patch, the temperatures that are displayed in /sys/class
> > when below 0 Deg C are 255 Deg C to 128 Deg C. With the patch, the
> > temperatures displayed below 0 Deg C are -1 Deg C to -128 Deg C as
> > expected.
> >
> Ah, yes, it is "int8_t", which is extended to a negative number.
> Sorry, I somehow read it as unsigned.
>
> Please run your patch through checkpatch --strict, fix what it reports,
> and resubmit.
I assume we fix errors but wanted to check on warnings as it looks
like this file has a lot.
--
Matthew L Weber / Pr Software Engineer
Airborne Information Systems / Security Systems and Software / Secure Platforms
MS 131-100, C Ave NE, Cedar Rapids, IA, 52498, USA
www.rockwellcollins.com
Note: Any Export License Required Information and License Restricted
Third Party Intellectual Property (TPIP) content must be encrypted and
sent to matthew.weber@xxxxxxxxxxxxxxxxxxxxxxxx.
--
To unsubscribe from this list: send the line "unsubscribe linux-hwmon" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
