[PATCH 3/3] dt-bindings: pinctrl: at91-pio4: convert Atmel's PIO4 bindings to json-schema

[Balakrishnan Sambath <balakrishnan.s@xxxxxxxxxxxxx>]

Convert the existing text DT bindings of Atmel's PIO4 pincontroller to
yaml based DT schema.

Signed-off-by: Balakrishnan Sambath <balakrishnan.s@xxxxxxxxxxxxx>
---
 .../bindings/pinctrl/atmel,at91-pio4-pinctrl.txt   |  98 ---------------
 .../bindings/pinctrl/atmel,sama5d2-pinctrl.yaml    | 140 +++++++++++++++++++++
 2 files changed, 140 insertions(+), 98 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pio4-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pio4-pinctrl.txt
deleted file mode 100644
index 774c3c269c40..000000000000
--- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pio4-pinctrl.txt
+++ /dev/null
@@ -1,98 +0,0 @@
-* Atmel PIO4 Controller
-
-The Atmel PIO4 controller is used to select the function of a pin and to
-configure it.
-
-Required properties:
-- compatible:
-	"atmel,sama5d2-pinctrl"
-	"microchip,sama7g5-pinctrl"
-- reg: base address and length of the PIO controller.
-- interrupts: interrupt outputs from the controller, one for each bank.
-- interrupt-controller: mark the device node as an interrupt controller.
-- #interrupt-cells: should be two.
-- gpio-controller: mark the device node as a gpio controller.
-- #gpio-cells: should be two.
-
-Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
-a general description of GPIO and interrupt bindings.
-
-Please refer to pinctrl-bindings.txt in this directory for details of the
-common pinctrl bindings used by client devices.
-
-Subnode format
-Each node (or subnode) will list the pins it needs and how to configured these
-pins.
-
-	node {
-		pinmux = <PIN_NUMBER_PINMUX>;
-		GENERIC_PINCONFIG;
-	};
-
-Required properties:
-- pinmux: integer array. Each integer represents a pin number plus mux and
-ioset settings. Use the macros from boot/dts/<soc>-pinfunc.h file to get the
-right representation of the pin.
-
-Optional properties:
-- GENERIC_PINCONFIG: generic pinconfig options to use:
-	- bias-disable, bias-pull-down, bias-pull-up, drive-open-drain,
-	 drive-push-pull input-schmitt-enable, input-debounce, output-low,
-	 output-high.
-	- for microchip,sama7g5-pinctrl only:
-		- slew-rate: 0 - disabled, 1 - enabled (default)
-- atmel,drive-strength: 0 or 1 for low drive, 2 for medium drive and 3 for
-high drive. The default value is low drive.
-
-Example:
-
-#include <sama5d2-pinfunc.h>
-
-...
-{
-	pioA: pinctrl@fc038000 {
-		compatible = "atmel,sama5d2-pinctrl";
-		reg = <0xfc038000 0x600>;
-		interrupts = <18 IRQ_TYPE_LEVEL_HIGH 7>,
-			     <68 IRQ_TYPE_LEVEL_HIGH 7>,
-			     <69 IRQ_TYPE_LEVEL_HIGH 7>,
-			     <70 IRQ_TYPE_LEVEL_HIGH 7>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-		gpio-controller;
-		#gpio-cells = <2>;
-		clocks = <&pioA_clk>;
-
-		pinctrl_i2c0_default: i2c0_default {
-			pinmux = <PIN_PD21__TWD0>,
-				 <PIN_PD22__TWCK0>;
-			bias-disable;
-		};
-
-		pinctrl_led_gpio_default: led_gpio_default {
-			pinmux = <PIN_PB0>,
-				 <PIN_PB5>;
-			bias-pull-up;
-			atmel,drive-strength = <ATMEL_PIO_DRVSTR_ME>;
-		};
-
-		pinctrl_sdmmc1_default: sdmmc1_default {
-			cmd_data {
-				pinmux = <PIN_PA28__SDMMC1_CMD>,
-					 <PIN_PA18__SDMMC1_DAT0>,
-					 <PIN_PA19__SDMMC1_DAT1>,
-					 <PIN_PA20__SDMMC1_DAT2>,
-					 <PIN_PA21__SDMMC1_DAT3>;
-				bias-pull-up;
-			};
-
-			ck_cd {
-				pinmux = <PIN_PA22__SDMMC1_CK>,
-					 <PIN_PA30__SDMMC1_CD>;
-				bias-disable;
-			};
-		};
-		...
-	};
-};
-...
diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,sama5d2-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/atmel,sama5d2-pinctrl.yaml
new file mode 100644
index 000000000000..8a2dee1d6dd3
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/atmel,sama5d2-pinctrl.yaml
@@ -0,0 +1,140 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/atmel,sama5d2-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Microchip PIO4 Controller
+
+maintainers:
+  - Balakrishnan Sambath <balakrishnan.s@xxxxxxxxxxxxx>
+
+description:
+  The Microchip PIO4 controller is used to select the function of a pin and to
+  configure it.
+
+
+properties:
+  compatible:
+    enum:
+      - microchip,sama7g5-pinctrl
+      - atmel,sama5d2-pinctrl
+
+  reg:
+    minItems: 1
+    maxItems: 2
+
+  interrupts:
+    description:
+      Interrupt outputs from the controller, one for each bank.
+
+  interrupt-controller: true
+
+  '#interrupt-cells':
+    const: 2
+
+  gpio-controller: true
+
+  '#gpio-cells':
+    const: 2
+
+  clocks:
+    maxItems: 1
+if:
+  properties:
+    compatible:
+      contains:
+        const: microchip,sama7g5-pinctrl
+then:
+  patternProperties:
+    '^.*([-_]default)?$':
+      anyOf:
+        - $ref: "#/$defs/mchp-pio4-pincfg-node-1"
+        - patternProperties:
+            '^[a-z_-][a-z_-]*$':
+              $ref: "#/$defs/mchp-pio4-pincfg-node-1"
+else:
+  patternProperties:
+    '^.*([-_]default)?$':
+      anyOf:
+        - $ref: "#/$defs/mchp-pio4-pincfg-node-2"
+        - patternProperties:
+            '^[a-z_-][a-z_-]*$':
+              $ref: "#/$defs/mchp-pio4-pincfg-node-2"
+
+$defs:
+  mchp-pio4-pincfg-node-1:
+    $ref: pincfg-node.yaml#properties
+    properties:
+      pinmux:
+        $ref: pinmux-node.yaml#/properties/pinmux
+      atmel,drive-strength:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1, 2, 3]
+        default: 0
+    required:
+      - pinmux
+
+  mchp-pio4-pincfg-node-2:
+    $ref: pincfg-node.yaml#properties
+    properties:
+      pinmux:
+        $ref: pinmux-node.yaml#/properties/pinmux
+    required:
+      - pinmux
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - interrupt-controller
+  - '#interrupt-cells'
+  - gpio-controller
+  - '#gpio-cells'
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/clock/at91.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/pinctrl/sama5d2-pinfunc.h>
+
+    pinctrl@fc038000 {
+        compatible = "atmel,sama5d2-pinctrl";
+        reg = <0xfc038000 0x600>;
+        interrupts = <18 IRQ_TYPE_LEVEL_HIGH 7>,
+                     <68 IRQ_TYPE_LEVEL_HIGH 7>,
+                     <69 IRQ_TYPE_LEVEL_HIGH 7>,
+                     <70 IRQ_TYPE_LEVEL_HIGH 7>;
+        interrupt-controller;
+        #interrupt-cells = <2>;
+        gpio-controller;
+        #gpio-cells = <2>;
+        clocks = <&pioA_clk>;
+
+        pinctrl_i2c0_default: i2c0_default {
+            pinmux = <PIN_PD21__TWD0>,
+                     <PIN_PD22__TWCK0>;
+            bias-disable;
+        };
+
+        pinctrl_sdmmc1_default: sdmmc1_default {
+            cmd_data {
+                pinmux = <PIN_PA28__SDMMC1_CMD>,
+                         <PIN_PA18__SDMMC1_DAT0>,
+                         <PIN_PA19__SDMMC1_DAT1>,
+                         <PIN_PA20__SDMMC1_DAT2>,
+                         <PIN_PA21__SDMMC1_DAT3>;
+                bias-pull-up;
+            };
+
+            ck_cd {
+                pinmux = <PIN_PA22__SDMMC1_CK>,
+                         <PIN_PA30__SDMMC1_CD>;
+                bias-disable;
+            };
+        };
+    };
+...

-- 
2.25.1