Re: [PATCH 33/37] arm64: dts: renesas: rzg3l-smarc-som: add initial support for RZ/G3S SMARC Carrier-II SoM

[claudiu beznea <claudiu.beznea@xxxxxxxxx>]

Hi, Geert,

On 15.09.2023 17:28, Geert Uytterhoeven wrote:
> Hi Claudiu,
> 
> Thanks for your patch!
> 
> On Tue, Sep 12, 2023 at 6:53 AM Claudiu <claudiu.beznea@xxxxxxxxx> wrote:
>> From: Claudiu Beznea <claudiu.beznea.uj@xxxxxxxxxxxxxx>
>>
>> Add initial support for RZ/G3S SMARC Carrier-II SoM. SoM contains the following
>> devices:
>> - RZ/G3S microcontroller: Renesas R9A08G045S33GBG
>> - 9-channel PMIC: Renesas RAA215300
>> - Clock Generator: Renesas 5L35023B
>> - 128M QSPI Flash: Renesas AT25QL128A
>> - 8G LPDDR4 SDRAM: Micron MT53D512M16D1DS-046
> 
> That's an 8 Gib part, so 1 GiB?
> 
>> - 64GB eMMC Flash: Micron MTFC64GBCAQTC
>> - 2x Gigabit Ethernet Transceiver: Microchip KSZ9131RNX
>> - 5x Current Monitors: Renesas ISL28025FR12Z
>>
>> The following interfaces are available on SoM board:
>> - 2 uSD interfaces
>> - 12-pin, 1.0mm pitch connector to the RZ/G3S ADC IO
>> - 4-pin, 1.0mm pitch connector to the RZ/G3S I3C IO
>> - JTAG connector
> 
> Please drop the description of parts you are not adding to the DTS yet.
> 
>> At the moment the 24MHz output of 5L35023B, memory SD ch0 (with all its
>> bits) were described in device tree.
>>
>> SD channel 0 of RZ/G3S is connected to an uSD card interface
>> and an eMMC. The selection b/w them is done though a hardware switch.
>> The DT will select b/w uSD and eMMC though SW_SD0_DEV_SEL build flag.
>>
>> Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@xxxxxxxxxxxxxx>
> 
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi
>> @@ -0,0 +1,147 @@
>> +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +/*
>> + * Device Tree Source for the R9A08G045S33 SMARC Carrier-II's SoM board.
>> + *
>> + * Copyright (C) 2023 Renesas Electronics Corp.
>> + */
>> +
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
>> +
>> +/*
>> + * Signals of SW_CONFIG switches:
>> + * @SW_SD0_DEV_SEL:
>> + *     0 - SD0 is connected to eMMC
>> + *     1 - SD0 is connected to uSD0 card
>> + */
>> +#define SW_SD0_DEV_SEL 1
>> +
>> +/ {
>> +       aliases {
>> +               mmc0 = &sdhi0;
>> +       };
>> +
>> +       chosen {
>> +               bootargs = "ignore_loglevel";
>> +               stdout-path = "serial0:115200n8";
>> +       };
>> +
>> +       memory@48000000 {
>> +               device-type = "memory";
>> +               /* First 128MB is reserved for secure area. */
>> +               reg = <0x0 0x48000000 0x0 0x38000000>;
>> +       };
>> +
>> +       reg_3p3v: regulator0 {
>> +               compatible = "regulator-fixed";
>> +               regulator-name = "fixed-3.3V";
>> +               regulator-min-microvolt = <3300000>;
>> +               regulator-max-microvolt = <3300000>;
>> +               regulator-boot-on;
>> +               regulator-always-on;
>> +       };
>> +
>> +#if SW_SD0_DEV_SEL
>> +       vccq_sdhi0: regulator1 {
>> +               compatible = "regulator-gpio";
>> +               regulator-name = "SDHI0 VccQ";
>> +               regulator-min-microvolt = <1800000>;
>> +               regulator-max-microvolt = <3300000>;
>> +               gpios = <&pinctrl RZG2L_GPIO(2, 2) GPIO_ACTIVE_HIGH>;
>> +               gpios-states = <1>;
>> +               states = <3300000 1>, <1800000 0>;
>> +       };
>> +#else
>> +       reg_1p8v: regulator1 {
>> +               compatible = "regulator-fixed";
>> +               regulator-name = "fixed-1.8V";
>> +               regulator-min-microvolt = <1800000>;
>> +               regulator-max-microvolt = <1800000>;
>> +               regulator-boot-on;
>> +               regulator-always-on;
>> +       };
>> +#endif
>> +};
>> +
>> +&extal_clk {
>> +       clock-frequency = <24000000>;
>> +};
>> +
>> +#if SW_SD0_DEV_SEL
>> +/* SD0 slot */
>> +&sdhi0 {
>> +       pinctrl-0 = <&sdhi0_pins>;
>> +       pinctrl-1 = <&sdhi0_uhs_pins>;
>> +       pinctrl-names = "default", "state_uhs";
>> +       vmmc-supply = <&reg_3p3v>;
>> +       vqmmc-supply = <&vccq_sdhi0>;
>> +       bus-width = <4>;
>> +       sd-uhs-sdr50;
>> +       sd-uhs-sdr104;
>> +       max-frequency = <125000000>;
>> +       status = "okay";
>> +};
>> +#else
>> +/* eMMC */
>> +&sdhi0 {
>> +       pinctrl-0 = <&sdhi0_emmc_pins>;
>> +       pinctrl-1 = <&sdhi0_emmc_pins>;
>> +       pinctrl-names = "default", "state_uhs";
>> +       vmmc-supply = <&reg_3p3v>;
>> +       vqmmc-supply = <&reg_1p8v>;
>> +       bus-width = <8>;
>> +       mmc-hs200-1_8v;
>> +       non-removable;
>> +       fixed-emmc-driver-type = <1>;
>> +       max-frequency = <125000000>;
>> +       status = "okay";
>> +};
>> +#endif
>> +
>> +&pinctrl {
>> +       sd0-pwr-en-hog {
>> +               gpio-hog;
>> +               gpios = <RZG2L_GPIO(2, 1) GPIO_ACTIVE_HIGH>;
> 
> According to the schematics, P2_1 controls power to the uSD slot.
> Hence shouldn't reg_3p3v above be modelled using regulator-gpio,
> with enable-gpios pointing to P2_1?

That should work. I'll check it, thanks!

> 
>> +               output-high;
>> +               line-name = "sd0_pwr_en";
>> +       };
> Gr{oetje,eeting}s,
> 
>                         Geert
>