Re: [PATCH v5 1/2] gpio: tps65219: add GPIO support for TPS65219 PMIC

[andy.shevchenko@xxxxxxxxx]

Wed, Jun 07, 2023 at 04:39:31PM +0200, Jerome Neanne kirjoitti:
> Add support for TPS65219 PMICs GPIO interface.
> 
> 3 GPIO pins:
> - GPIO0 only is IO but input mode reserved for MULTI_DEVICE_ENABLE usage.
> - GPIO1 and GPIO2 are Output only and referred as GPO1 and GPO2 in spec.
> 
> GPIO0 is statically configured as input or output prior to Linux boot.
> it is used for MULTI_DEVICE_ENABLE function.
> This setting is statically configured by NVM.
> GPIO0 can't be used as a generic GPIO (specification Table 8-34).
> It's either a GPO when MULTI_DEVICE_EN=0 or a GPI when MULTI_DEVICE_EN=1.
> 
> Datasheet describes specific usage for non standard GPIO.

Reviewed-by: Andy Shevchenko <andy.shevchenko@xxxxxxxxx>

I forgot if I asked about gpio-regmap use possibility, but it can be done
as a followup if seems valuable.

> Datasheet: https://www.ti.com/lit/ds/symlink/tps65219.pdf
> Co-developed-by: Jonathan Cormier <jcormier@xxxxxxxxxxxxxxxx>
> Signed-off-by: Jonathan Cormier <jcormier@xxxxxxxxxxxxxxxx>
> Reviewed-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
> Signed-off-by: Jerome Neanne <jneanne@xxxxxxxxxxxx>
> ---
>  MAINTAINERS                  |   1 +
>  drivers/gpio/Kconfig         |  16 ++++
>  drivers/gpio/Makefile        |   1 +
>  drivers/gpio/gpio-tps65219.c | 185 +++++++++++++++++++++++++++++++++++++++++++
>  4 files changed, 203 insertions(+)
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index c0cde28c62c6..d912b7465e84 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -15398,6 +15398,7 @@ T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap.git
>  F:	arch/arm/configs/omap2plus_defconfig
>  F:	arch/arm/mach-omap2/
>  F:	drivers/bus/ti-sysc.c
> +F:	drivers/gpio/gpio-tps65219.c
>  F:	drivers/i2c/busses/i2c-omap.c
>  F:	drivers/irqchip/irq-omap-intc.c
>  F:	drivers/mfd/*omap*.c
> diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
> index 5521f060d58e..047af064335d 100644
> --- a/drivers/gpio/Kconfig
> +++ b/drivers/gpio/Kconfig
> @@ -1440,6 +1440,22 @@ config GPIO_TPS65218
>  	  Select this option to enable GPIO driver for the TPS65218
>  	  chip family.
>  
> +config GPIO_TPS65219
> +	tristate "TPS65219 GPIO"
> +	depends on MFD_TPS65219
> +	default MFD_TPS65219
> +	help
> +	  Select this option to enable GPIO driver for the TPS65219 chip
> +	  family.
> +	  GPIO0 is statically configured as either input or output prior to
> +	  Linux boot. It is used for MULTI_DEVICE_ENABLE function. This setting
> +	  is statically configured by NVM. GPIO0 can't be used as a generic
> +	  GPIO. It's either a GPO when MULTI_DEVICE_EN=0 or a GPI when
> +	  MULTI_DEVICE_EN=1.
> +
> +	  This driver can also be built as a module. If so, the module will be
> +	  called gpio_tps65219.
> +
>  config GPIO_TPS6586X
>  	bool "TPS6586X GPIO"
>  	depends on MFD_TPS6586X
> diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
> index 20036af3acb1..7843b16f5d59 100644
> --- a/drivers/gpio/Makefile
> +++ b/drivers/gpio/Makefile
> @@ -160,6 +160,7 @@ obj-$(CONFIG_GPIO_TN48M_CPLD)		+= gpio-tn48m.o
>  obj-$(CONFIG_GPIO_TPIC2810)		+= gpio-tpic2810.o
>  obj-$(CONFIG_GPIO_TPS65086)		+= gpio-tps65086.o
>  obj-$(CONFIG_GPIO_TPS65218)		+= gpio-tps65218.o
> +obj-$(CONFIG_GPIO_TPS65219)		+= gpio-tps65219.o
>  obj-$(CONFIG_GPIO_TPS6586X)		+= gpio-tps6586x.o
>  obj-$(CONFIG_GPIO_TPS65910)		+= gpio-tps65910.o
>  obj-$(CONFIG_GPIO_TPS65912)		+= gpio-tps65912.o
> diff --git a/drivers/gpio/gpio-tps65219.c b/drivers/gpio/gpio-tps65219.c
> new file mode 100644
> index 000000000000..7b38aa360112
> --- /dev/null
> +++ b/drivers/gpio/gpio-tps65219.c
> @@ -0,0 +1,185 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * GPIO driver for TI TPS65219 PMICs
> + *
> + * Copyright (C) 2022 Texas Instruments Incorporated - http://www.ti.com/
> + */
> +
> +#include <linux/bits.h>
> +#include <linux/gpio/driver.h>
> +#include <linux/mfd/tps65219.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +
> +#define TPS65219_GPIO0_DIR_MASK		BIT(3)
> +#define TPS65219_GPIO0_OFFSET		2
> +#define TPS65219_GPIO0_IDX		0
> +#define TPS65219_GPIO_DIR_IN		1
> +#define TPS65219_GPIO_DIR_OUT		0
> +
> +struct tps65219_gpio {
> +	struct gpio_chip gpio_chip;
> +	struct tps65219 *tps;
> +};
> +
> +static int tps65219_gpio_get_direction(struct gpio_chip *gc, unsigned int offset)
> +{
> +	struct tps65219_gpio *gpio = gpiochip_get_data(gc);
> +	int ret, val;
> +
> +	if (offset != TPS65219_GPIO0_IDX)
> +		return GPIO_LINE_DIRECTION_OUT;
> +
> +	ret = regmap_read(gpio->tps->regmap, TPS65219_REG_MFP_1_CONFIG, &val);
> +	if (ret)
> +		return ret;
> +
> +	return !!(val & TPS65219_GPIO0_DIR_MASK);
> +}
> +
> +static int tps65219_gpio_get(struct gpio_chip *gc, unsigned int offset)
> +{
> +	struct tps65219_gpio *gpio = gpiochip_get_data(gc);
> +	struct device *dev = gpio->tps->dev;
> +	int ret, val;
> +
> +	if (offset != TPS65219_GPIO0_IDX) {
> +		dev_err(dev, "GPIO%d is output only, cannot get\n", offset);
> +		return -ENOTSUPP;
> +	}
> +
> +	ret = regmap_read(gpio->tps->regmap, TPS65219_REG_MFP_CTRL, &val);
> +	if (ret)
> +		return ret;
> +
> +	ret = !!(val & BIT(TPS65219_MFP_GPIO_STATUS_MASK));
> +	dev_warn(dev, "GPIO%d = %d, MULTI_DEVICE_ENABLE, not a standard GPIO\n", offset, ret);
> +
> +	/*
> +	 * Depending on NVM config, return an error if direction is output, otherwise the GPIO0
> +	 * status bit.
> +	 */
> +
> +	if (tps65219_gpio_get_direction(gc, offset) == TPS65219_GPIO_DIR_OUT)
> +		return -ENOTSUPP;
> +
> +	return ret;
> +}
> +
> +static void tps65219_gpio_set(struct gpio_chip *gc, unsigned int offset, int value)
> +{
> +	struct tps65219_gpio *gpio = gpiochip_get_data(gc);
> +	struct device *dev = gpio->tps->dev;
> +	int v, mask, bit;
> +
> +	bit = (offset == TPS65219_GPIO0_IDX) ? TPS65219_GPIO0_OFFSET : offset - 1;
> +
> +	mask = BIT(bit);
> +	v = value ? mask : 0;
> +
> +	if (regmap_update_bits(gpio->tps->regmap, TPS65219_REG_GENERAL_CONFIG, mask, v))
> +		dev_err(dev, "GPIO%d, set to value %d failed.\n", offset, value);
> +}
> +
> +static int tps65219_gpio_change_direction(struct gpio_chip *gc, unsigned int offset,
> +					  unsigned int direction)
> +{
> +	struct tps65219_gpio *gpio = gpiochip_get_data(gc);
> +	struct device *dev = gpio->tps->dev;
> +
> +	/*
> +	 * Documentation is stating that GPIO0 direction must not be changed in Linux:
> +	 * Table 8-34. MFP_1_CONFIG(3): MULTI_DEVICE_ENABLE, should only be changed in INITIALIZE
> +	 * state (prior to ON Request).
> +	 * Set statically by NVM, changing direction in application can cause a hang.
> +	 * Below can be used for test purpose only.
> +	 */
> +
> +	if (IS_ENABLED(CONFIG_DEBUG_GPIO)) {
> +		int ret = regmap_update_bits(gpio->tps->regmap, TPS65219_REG_MFP_1_CONFIG,
> +					     TPS65219_GPIO0_DIR_MASK, direction);
> +		if (ret) {
> +			dev_err(dev,
> +				"GPIO DEBUG enabled: Fail to change direction to %u for GPIO%d.\n",
> +				direction, offset);
> +			return ret;
> +		}
> +	}
> +
> +	dev_err(dev,
> +		"GPIO%d direction set by NVM, change to %u failed, not allowed by specification\n",
> +		 offset, direction);
> +
> +	return -ENOTSUPP;
> +}
> +
> +static int tps65219_gpio_direction_input(struct gpio_chip *gc, unsigned int offset)
> +{
> +	struct tps65219_gpio *gpio = gpiochip_get_data(gc);
> +	struct device *dev = gpio->tps->dev;
> +
> +	if (offset != TPS65219_GPIO0_IDX) {
> +		dev_err(dev, "GPIO%d is output only, cannot change to input\n", offset);
> +		return -ENOTSUPP;
> +	}
> +
> +	if (tps65219_gpio_get_direction(gc, offset) == TPS65219_GPIO_DIR_IN)
> +		return 0;
> +
> +	return tps65219_gpio_change_direction(gc, offset, TPS65219_GPIO_DIR_IN);
> +}
> +
> +static int tps65219_gpio_direction_output(struct gpio_chip *gc, unsigned int offset, int value)
> +{
> +	tps65219_gpio_set(gc, offset, value);
> +	if (offset != TPS65219_GPIO0_IDX)
> +		return 0;
> +
> +	if (tps65219_gpio_get_direction(gc, offset) == TPS65219_GPIO_DIR_OUT)
> +		return 0;
> +
> +	return tps65219_gpio_change_direction(gc, offset, TPS65219_GPIO_DIR_OUT);
> +}
> +
> +static const struct gpio_chip tps65219_template_chip = {
> +	.label			= "tps65219-gpio",
> +	.owner			= THIS_MODULE,
> +	.get_direction		= tps65219_gpio_get_direction,
> +	.direction_input	= tps65219_gpio_direction_input,
> +	.direction_output	= tps65219_gpio_direction_output,
> +	.get			= tps65219_gpio_get,
> +	.set			= tps65219_gpio_set,
> +	.base			= -1,
> +	.ngpio			= 3,
> +	.can_sleep		= true,
> +};
> +
> +static int tps65219_gpio_probe(struct platform_device *pdev)
> +{
> +	struct tps65219 *tps = dev_get_drvdata(pdev->dev.parent);
> +	struct tps65219_gpio *gpio;
> +
> +	gpio = devm_kzalloc(&pdev->dev, sizeof(*gpio), GFP_KERNEL);
> +	if (!gpio)
> +		return -ENOMEM;
> +
> +	gpio->tps = tps;
> +	gpio->gpio_chip = tps65219_template_chip;
> +	gpio->gpio_chip.parent = tps->dev;
> +
> +	return devm_gpiochip_add_data(&pdev->dev, &gpio->gpio_chip, gpio);
> +}
> +
> +static struct platform_driver tps65219_gpio_driver = {
> +	.driver = {
> +		.name = "tps65219-gpio",
> +	},
> +	.probe = tps65219_gpio_probe,
> +};
> +module_platform_driver(tps65219_gpio_driver);
> +
> +MODULE_ALIAS("platform:tps65219-gpio");
> +MODULE_AUTHOR("Jonathan Cormier <jcormier@xxxxxxxxxxxxxxxx>");
> +MODULE_DESCRIPTION("TPS65219 GPIO driver");
> +MODULE_LICENSE("GPL");
> 
> -- 
> 2.34.1
> 

-- 
With Best Regards,
Andy Shevchenko