Re: [RFC PATCH v2 1/2] dt-bindings: sc16is7xx: Add property to change GPIO function

[Lech Perczak <lech.perczak@xxxxxxxxxxxxxxx>]

Hello Hugo,

W dniu 18.05.2023 o 15:29, Hugo Villeneuve pisze:
> From: Hugo Villeneuve <hvilleneuve@xxxxxxxxxxxx>
>
> Some variants in this series of uart controllers have GPIO pins that
> are shared between GPIO and modem control lines.
>
> The pin mux mode (GPIO or modem control lines) can be set for each
> ports (channels) supported by the variant.
>
> This adds a property to the device tree to set the GPIO pin mux to
> modem control lines on selected ports if needed.
>
> Signed-off-by: Hugo Villeneuve <hvilleneuve@xxxxxxxxxxxx>
> ---
> v1 -> v2: Add nxp vendor prefix
>           Add git base-commit
>
>  .../bindings/serial/nxp,sc16is7xx.txt         | 28 +++++++++++++++++++
>  1 file changed, 28 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt
> index 0fa8e3e43bf8..23a81c83f012 100644
> --- a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt
> +++ b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt
> @@ -23,6 +23,9 @@ Optional properties:
>      1 = active low.
>  - irda-mode-ports: An array that lists the indices of the port that
>                    should operate in IrDA mode.
> +- nxp,modem-control-line-ports: An array that lists the indices of the port that
> +                               should have shared GPIO lines configured as modem
> +                               control lines.
>
>  Example:
>          sc16is750: sc16is750@51 {
> @@ -35,6 +38,17 @@ Example:
>                  #gpio-cells = <2>;
>          };
>
> +       sc16is752: sc16is752@54 {
> +               compatible = "nxp,sc16is752";
> +               reg = <0x54>;
> +               clocks = <&clk20m>;
> +               interrupt-parent = <&gpio3>;
> +               interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
> +               nxp,modem-control-line-ports = <1>; /* Port 1 as modem control lines */
> +               gpio-controller; /* Port 0 as GPIOs */
> +               #gpio-cells = <2>;
> +       };
> +
>  * spi as bus
>
>  Required properties:
> @@ -59,6 +73,9 @@ Optional properties:
>      1 = active low.
>  - irda-mode-ports: An array that lists the indices of the port that
>                    should operate in IrDA mode.
> +- nxp,modem-control-line-ports: An array that lists the indices of the port that
> +                               should have shared GPIO lines configured as modem
> +                               control lines.
>
>  Example:
>         sc16is750: sc16is750@0 {
> @@ -70,3 +87,14 @@ Example:
>                 gpio-controller;
>                 #gpio-cells = <2>;
>         };
> +
> +       sc16is752: sc16is752@0 {
> +               compatible = "nxp,sc16is752";
> +               reg = <0>;
> +               clocks = <&clk20m>;
> +               interrupt-parent = <&gpio3>;
> +               interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
> +               nxp,modem-control-line-ports = <1>; /* Port 1 as modem control lines */
Just a minor nitpick: an example showing syntax for both ports would be great.
This can be included here, leaving the previous example intact. Otherwise, LGTM.
> +               gpio-controller; /* Port 0 as GPIOs */
> +               #gpio-cells = <2>;
> +       };
>
> base-commit: 4d6d4c7f541d7027beed4fb86eb2c451bd8d6fff
> --
> 2.30.2

-- 
Pozdrawiam/With kind regards,
Lech Perczak

Sr. Software Engineer
Camlin Technologies Poland Limited Sp. z o.o.
Strzegomska 54,
53-611 Wroclaw
Tel:     (+48) 71 75 000 16
Email:   lech.perczak@xxxxxxxxxxxxxxx
Website: http://www.camlingroup.com