Re: [PATCH v3 14/18] arm64: dts: qcom: sa8775p: add PMIC GPIO controller nodes

[Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>]

On 27.03.2023 14:53, Bartosz Golaszewski wrote:
> From: Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx>
> 
> Add GPIO controller nodes to PMICs that have the GPIO hooked up on
> sa8775p-ride.
> 
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>

Konrad
>  arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi | 40 +++++++++++++++++++++
>  1 file changed, 40 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
> index be12997a080c..7602cca47bae 100644
> --- a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
> @@ -125,6 +125,16 @@ pmm8654au_0_pon_resin: resin {
>  				status = "disabled";
>  			};
>  		};
> +
> +		pmm8654au_0_gpios: gpio@8800 {
> +			compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio";
> +			reg = <0x8800>;
> +			gpio-controller;
> +			gpio-ranges = <&pmm8654au_0_gpios 0 0 12>;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
>  	};
>  
>  	pmm8654au_1: pmic@2 {
> @@ -139,6 +149,16 @@ pmm8654au_1_temp_alarm: temp-alarm@a00 {
>  			interrupts-extended = <&spmi_bus 0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
>  			#thermal-sensor-cells = <0>;
>  		};
> +
> +		pmm8654au_1_gpios: gpio@8800 {
> +			compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio";
> +			reg = <0x8800>;
> +			gpio-controller;
> +			gpio-ranges = <&pmm8654au_2_gpios 0 0 12>;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
>  	};
>  
>  	pmm8654au_2: pmic@4 {
> @@ -153,6 +173,16 @@ pmm8654au_2_temp_alarm: temp-alarm@a00 {
>  			interrupts-extended = <&spmi_bus 0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
>  			#thermal-sensor-cells = <0>;
>  		};
> +
> +		pmm8654au_2_gpios: gpio@8800 {
> +			compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio";
> +			reg = <0x8800>;
> +			gpio-controller;
> +			gpio-ranges = <&pmm8654au_2_gpios 0 0 12>;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
>  	};
>  
>  	pmm8654au_3: pmic@6 {
> @@ -167,5 +197,15 @@ pmm8654au_3_temp_alarm: temp-alarm@a00 {
>  			interrupts-extended = <&spmi_bus 0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
>  			#thermal-sensor-cells = <0>;
>  		};
> +
> +		pmm8654au_3_gpios: gpio@8800 {
> +			compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio";
> +			reg = <0x8800>;
> +			gpio-controller;
> +			gpio-ranges = <&pmm8654au_3_gpios 0 0 12>;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
>  	};
>  };