Re: [PATCH v2 4/4] dt-bindings: pinctrl: qcom,sdm630: convert to dtschema

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 

On Tue, Oct 11, 2022 at 03:02:31PM -0400, Krzysztof Kozlowski wrote:
> Convert Qualcomm SDM630 and SDM660 pin controller bindings to DT schema.
> Keep the parsing of pin configuration subnodes consistent with other
> Qualcomm schemas (children named with '-state' suffix, their children
> with '-pins').
> 
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
> Reviewed-by: Rob Herring <robh@xxxxxxxxxx>

Reviewed-by: Bjorn Andersson <andersson@xxxxxxxxxx>

Regards,
Bjorn

> 
> ---
> 
> Changes since v1:
> 1. Add tags.
> 2. Adjust a bit bindings description to match other bindings.
> 3. Add tlmm label to example, because it is used in gpio-ranges.
> ---
>  .../bindings/pinctrl/qcom,sdm630-pinctrl.yaml | 188 +++++++++++++++++
>  .../bindings/pinctrl/qcom,sdm660-pinctrl.txt  | 191 ------------------
>  2 files changed, 188 insertions(+), 191 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,sdm630-pinctrl.yaml
>  delete mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,sdm660-pinctrl.txt
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdm630-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sdm630-pinctrl.yaml
> new file mode 100644
> index 000000000000..bd4fd8404aa4
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sdm630-pinctrl.yaml
> @@ -0,0 +1,188 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/qcom,sdm630-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm SDM630 and SDM660 TLMM pin controller
> +
> +maintainers:
> +  - Bjorn Andersson <andersson@xxxxxxxxxx>
> +  - Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
> +
> +description:
> +  Top Level Mode Multiplexer pin controller in Qualcomm SDM630 and SDM660 SoC.
> +
> +allOf:
> +  - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
> +
> +properties:
> +  compatible:
> +    enum:
> +      - qcom,sdm630-pinctrl
> +      - qcom,sdm660-pinctrl
> +
> +  reg:
> +    maxItems: 3
> +
> +  reg-names:
> +    items:
> +      - const: south
> +      - const: center
> +      - const: north
> +
> +  interrupts: true
> +  interrupt-controller: true
> +  "#interrupt-cells": true
> +  gpio-controller: true
> +
> +  gpio-reserved-ranges:
> +    minItems: 1
> +    maxItems: 57
> +
> +  gpio-line-names:
> +    maxItems: 114
> +
> +  "#gpio-cells": true
> +  gpio-ranges: true
> +  wakeup-parent: true
> +
> +patternProperties:
> +  "-state$":
> +    oneOf:
> +      - $ref: "#/$defs/qcom-sdm630-tlmm-state"
> +      - patternProperties:
> +          "-pins$":
> +            $ref: "#/$defs/qcom-sdm630-tlmm-state"
> +        additionalProperties: false
> +
> +$defs:
> +  qcom-sdm630-tlmm-state:
> +    type: object
> +    description:
> +      Pinctrl node's client devices use subnodes for desired pin configuration.
> +      Client device subnodes use below standard properties.
> +    $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
> +
> +    properties:
> +      pins:
> +        description:
> +          List of gpio pins affected by the properties specified in this
> +          subnode.
> +        items:
> +          oneOf:
> +            - pattern: "^gpio([0-9]|[1-9][0-9]|10[0-9]|11[0-3])$"
> +            - enum: [ sdc1_clk, sdc1_cmd, sdc1_data, sdc1_rclk, sdc2_clk,
> +                      sdc2_cmd, sdc2_data ]
> +        minItems: 1
> +        maxItems: 36
> +
> +      function:
> +        description:
> +          Specify the alternative function to be configured for the specified
> +          pins.
> +        enum: [ adsp_ext, agera_pll, atest_char, atest_char0, atest_char1,
> +                atest_char2, atest_char3, atest_gpsadc0, atest_gpsadc1,
> +                atest_tsens, atest_tsens2, atest_usb1, atest_usb10,
> +                atest_usb11, atest_usb12, atest_usb13, atest_usb2, atest_usb20,
> +                atest_usb21, atest_usb22, atest_usb23, audio_ref, bimc_dte0,
> +                bimc_dte1, blsp_i2c1, blsp_i2c2, blsp_i2c3, blsp_i2c4,
> +                blsp_i2c5, blsp_i2c6, blsp_i2c7, blsp_i2c8_a, blsp_i2c8_b,
> +                blsp_spi1, blsp_spi2, blsp_spi3, blsp_spi3_cs1, blsp_spi3_cs2,
> +                blsp_spi4, blsp_spi5, blsp_spi6, blsp_spi7, blsp_spi8_a,
> +                blsp_spi8_b, blsp_spi8_cs1, blsp_spi8_cs2, blsp_uart1,
> +                blsp_uart2, blsp_uart5, blsp_uart6_a, blsp_uart6_b, blsp_uim1,
> +                blsp_uim2, blsp_uim5, blsp_uim6, cam_mclk, cci_async, cci_i2c,
> +                cri_trng, cri_trng0, cri_trng1, dbg_out, ddr_bist, gcc_gp1,
> +                gcc_gp2, gcc_gp3, gpio, gps_tx_a, gps_tx_b, gps_tx_c,
> +                isense_dbg, jitter_bist, ldo_en, ldo_update, m_voc, mdp_vsync,
> +                mdss_vsync0, mdss_vsync1, mdss_vsync2, mdss_vsync3, mss_lte,
> +                nav_pps_a, nav_pps_b, nav_pps_c, pa_indicator, phase_flag0,
> +                phase_flag1, phase_flag10, phase_flag11, phase_flag12,
> +                phase_flag13, phase_flag14, phase_flag15, phase_flag16,
> +                phase_flag17, phase_flag18, phase_flag19, phase_flag2,
> +                phase_flag20, phase_flag21, phase_flag22, phase_flag23,
> +                phase_flag24, phase_flag25, phase_flag26, phase_flag27,
> +                phase_flag28, phase_flag29, phase_flag3, phase_flag30,
> +                phase_flag31, phase_flag4, phase_flag5, phase_flag6,
> +                phase_flag7, phase_flag8, phase_flag9, pll_bypassnl, pll_reset,
> +                pri_mi2s, pri_mi2s_ws, prng_rosc, pwr_crypto, pwr_modem,
> +                pwr_nav, qdss_cti0_a, qdss_cti0_b, qdss_cti1_a, qdss_cti1_b,
> +                qdss_gpio, qdss_gpio0, qdss_gpio1, qdss_gpio10, qdss_gpio11,
> +                qdss_gpio12, qdss_gpio13, qdss_gpio14, qdss_gpio15, qdss_gpio2,
> +                qdss_gpio3, qdss_gpio4, qdss_gpio5, qdss_gpio6, qdss_gpio7,
> +                qdss_gpio8, qdss_gpio9, qlink_enable, qlink_request, qspi_clk,
> +                qspi_cs, qspi_data0, qspi_data1, qspi_data2, qspi_data3,
> +                qspi_resetn, sec_mi2s, sndwire_clk, sndwire_data, sp_cmu,
> +                ssc_irq, tgu_ch0, tgu_ch1, tsense_pwm1, tsense_pwm2, uim1_clk,
> +                uim1_data, uim1_present, uim1_reset, uim2_clk, uim2_data,
> +                uim2_present, uim2_reset, uim_batt, vfr_1, vsense_clkout,
> +                vsense_data0, vsense_data1, vsense_mode, wlan1_adc0,
> +                wlan1_adc1, wlan2_adc0, wlan2_adc1 ]
> +
> +      bias-disable: true
> +      bias-pull-down: true
> +      bias-pull-up: true
> +      drive-strength: true
> +      input-enable: true
> +      output-high: true
> +      output-low: true
> +
> +    required:
> +      - pins
> +
> +    additionalProperties: false
> +
> +required:
> +  - compatible
> +  - reg
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> +    tlmm: pinctrl@3100000 {
> +        compatible = "qcom,sdm630-pinctrl";
> +        reg = <0x03100000 0x400000>,
> +              <0x03500000 0x400000>,
> +              <0x03900000 0x400000>;
> +        reg-names = "south", "center", "north";
> +        interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> +        gpio-controller;
> +        gpio-ranges = <&tlmm 0 0 114>;
> +        #gpio-cells = <2>;
> +        interrupt-controller;
> +        #interrupt-cells = <2>;
> +
> +        blsp1-uart1-default-state {
> +            pins = "gpio0", "gpio1", "gpio2", "gpio3";
> +            function = "gpio";
> +            drive-strength = <2>;
> +            bias-disable;
> +        };
> +
> +        blsp2_uart1_default: blsp2-uart1-active-state {
> +            tx-rts-pins {
> +                pins = "gpio16", "gpio19";
> +                function = "blsp_uart5";
> +                drive-strength = <2>;
> +                bias-disable;
> +            };
> +
> +            rx-pins {
> +                pins = "gpio17";
> +                function = "blsp_uart5";
> +                drive-strength = <2>;
> +                bias-pull-up;
> +            };
> +
> +            cts-pins {
> +                pins = "gpio18";
> +                function = "blsp_uart5";
> +                drive-strength = <2>;
> +                bias-pull-down;
> +            };
> +        };
> +    };
> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdm660-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,sdm660-pinctrl.txt
> deleted file mode 100644
> index be034d329e10..000000000000
> --- a/Documentation/devicetree/bindings/pinctrl/qcom,sdm660-pinctrl.txt
> +++ /dev/null
> @@ -1,191 +0,0 @@
> -Qualcomm Technologies, Inc. SDM660 TLMM block
> -
> -This binding describes the Top Level Mode Multiplexer block found in the
> -SDM660 platform.
> -
> -- compatible:
> -	Usage: required
> -	Value type: <string>
> -	Definition: must be "qcom,sdm660-pinctrl" or
> -		    "qcom,sdm630-pinctrl".
> -
> -- reg:
> -	Usage: required
> -	Value type: <prop-encoded-array>
> -	Definition: the base address and size of the north, center and south
> -		    TLMM tiles.
> -
> -- reg-names:
> -       Usage: required
> -       Value type: <stringlist>
> -       Definition: names for the cells of reg, must contain "north", "center"
> -                   and "south".
> -
> -- interrupts:
> -	Usage: required
> -	Value type: <prop-encoded-array>
> -	Definition: should specify the TLMM summary IRQ.
> -
> -- interrupt-controller:
> -	Usage: required
> -	Value type: <none>
> -	Definition: identifies this node as an interrupt controller
> -
> -- #interrupt-cells:
> -	Usage: required
> -	Value type: <u32>
> -	Definition: must be 2. Specifying the pin number and flags, as defined
> -		    in <dt-bindings/interrupt-controller/irq.h>
> -
> -- gpio-controller:
> -	Usage: required
> -	Value type: <none>
> -	Definition: identifies this node as a gpio controller
> -
> -- gpio-ranges:
> -	Usage: required
> -	Value type: <prop-encoded-array>
> -	Definition: Specifies the mapping between gpio controller and
> -		    pin-controller pins.
> -
> -- #gpio-cells:
> -	Usage: required
> -	Value type: <u32>
> -	Definition: must be 2. Specifying the pin number and flags, as defined
> -		    in <dt-bindings/gpio/gpio.h>
> -
> -Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
> -a general description of GPIO and interrupt bindings.
> -
> -Please refer to pinctrl-bindings.txt in this directory for details of the
> -common pinctrl bindings used by client devices, including the meaning of the
> -phrase "pin configuration node".
> -
> -The pin configuration nodes act as a container for an arbitrary number of
> -subnodes. Each of these subnodes represents some desired configuration for a
> -pin, a group, or a list of pins or groups. This configuration can include the
> -mux function to select on those pin(s)/group(s), and various pin configuration
> -parameters, such as pull-up, drive strength, etc.
> -
> -
> -PIN CONFIGURATION NODES:
> -
> -The name of each subnode is not important; all subnodes should be enumerated
> -and processed purely based on their content.
> -
> -Each subnode only affects those parameters that are explicitly listed. In
> -other words, a subnode that lists a mux function but no pin configuration
> -parameters implies no information about any pin configuration parameters.
> -Similarly, a pin subnode that describes a pullup parameter implies no
> -information about e.g. the mux function.
> -
> -
> -The following generic properties as defined in pinctrl-bindings.txt are valid
> -to specify in a pin configuration subnode:
> -
> -- pins:
> -	Usage: required
> -	Value type: <string-array>
> -	Definition: List of gpio pins affected by the properties specified in
> -		    this subnode.  Valid pins are:
> -		    gpio0-gpio113,
> -		        Supports mux, bias and drive-strength
> -		    sdc1_clk, sdc1_cmd, sdc1_data sdc2_clk, sdc2_cmd, sdc2_data sdc1_rclk,
> -		        Supports bias and drive-strength
> -
> -- function:
> -	Usage: required
> -	Value type: <string>
> -	Definition: Specify the alternative function to be configured for the
> -		    specified pins. Functions are only valid for gpio pins.
> -		    Valid values are:
> -		    adsp_ext, agera_pll, atest_char, atest_char0, atest_char1,
> -		    atest_char2, atest_char3, atest_gpsadc0, atest_gpsadc1,
> -		    atest_tsens, atest_tsens2, atest_usb1, atest_usb10,
> -		    atest_usb11, atest_usb12, atest_usb13, atest_usb2,
> -		    atest_usb20, atest_usb21, atest_usb22, atest_usb23,
> -		    audio_ref, bimc_dte0, bimc_dte1, blsp_i2c1, blsp_i2c2,
> -		    blsp_i2c3, blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_i2c7,
> -		    blsp_i2c8_a, blsp_i2c8_b, blsp_spi1, blsp_spi2, blsp_spi3,
> -		    blsp_spi3_cs1, blsp_spi3_cs2, blsp_spi4, blsp_spi5,
> -		    blsp_spi6, blsp_spi7, blsp_spi8_a, blsp_spi8_b,
> -		    blsp_spi8_cs1, blsp_spi8_cs2, blsp_uart1, blsp_uart2,
> -		    blsp_uart5, blsp_uart6_a, blsp_uart6_b, blsp_uim1,
> -		    blsp_uim2, blsp_uim5, blsp_uim6, cam_mclk, cci_async,
> -		    cci_i2c, cri_trng, cri_trng0, cri_trng1, dbg_out, ddr_bist,
> -		    gcc_gp1, gcc_gp2, gcc_gp3, gpio, gps_tx_a, gps_tx_b, gps_tx_c,
> -		    isense_dbg, jitter_bist, ldo_en, ldo_update, m_voc, mdp_vsync,
> -		    mdss_vsync0, mdss_vsync1, mdss_vsync2, mdss_vsync3, mss_lte,
> -		    nav_pps_a, nav_pps_b, nav_pps_c, pa_indicator, phase_flag0,
> -		    phase_flag1, phase_flag10, phase_flag11, phase_flag12,
> -		    phase_flag13, phase_flag14, phase_flag15, phase_flag16,
> -		    phase_flag17, phase_flag18, phase_flag19, phase_flag2,
> -		    phase_flag20, phase_flag21, phase_flag22, phase_flag23,
> -		    phase_flag24, phase_flag25, phase_flag26, phase_flag27,
> -		    phase_flag28, phase_flag29, phase_flag3, phase_flag30,
> -		    phase_flag31, phase_flag4, phase_flag5, phase_flag6,
> -		    phase_flag7, phase_flag8, phase_flag9, pll_bypassnl,
> -		    pll_reset, pri_mi2s, pri_mi2s_ws, prng_rosc, pwr_crypto,
> -		    pwr_modem, pwr_nav, qdss_cti0_a, qdss_cti0_b, qdss_cti1_a,
> -		    qdss_cti1_b, qdss_gpio, qdss_gpio0, qdss_gpio1, qdss_gpio10,
> -		    qdss_gpio11, qdss_gpio12, qdss_gpio13, qdss_gpio14, qdss_gpio15,
> -		    qdss_gpio2, qdss_gpio3, qdss_gpio4, qdss_gpio5, qdss_gpio6,
> -		    qdss_gpio7, qdss_gpio8, qdss_gpio9, qlink_enable, qlink_request,
> -		    qspi_clk, qspi_cs, qspi_data0, qspi_data1, qspi_data2,
> -		    qspi_data3, qspi_resetn, sec_mi2s, sndwire_clk, sndwire_data,
> -		    sp_cmu, ssc_irq, tgu_ch0, tgu_ch1, tsense_pwm1, tsense_pwm2,
> -		    uim1_clk, uim1_data, uim1_present, uim1_reset, uim2_clk,
> -		    uim2_data, uim2_present, uim2_reset, uim_batt, vfr_1,
> -		    vsense_clkout, vsense_data0, vsense_data1, vsense_mode,
> -		    wlan1_adc0, wlan1_adc1, wlan2_adc0, wlan2_adc1
> -
> -- bias-disable:
> -	Usage: optional
> -	Value type: <none>
> -	Definition: The specified pins should be configured as no pull.
> -
> -- bias-pull-down:
> -	Usage: optional
> -	Value type: <none>
> -	Definition: The specified pins should be configured as pull down.
> -
> -- bias-pull-up:
> -	Usage: optional
> -	Value type: <none>
> -	Definition: The specified pins should be configured as pull up.
> -
> -- output-high:
> -	Usage: optional
> -	Value type: <none>
> -	Definition: The specified pins are configured in output mode, driven
> -		    high.
> -		    Not valid for sdc pins.
> -
> -- output-low:
> -	Usage: optional
> -	Value type: <none>
> -	Definition: The specified pins are configured in output mode, driven
> -		    low.
> -		    Not valid for sdc pins.
> -
> -- drive-strength:
> -	Usage: optional
> -	Value type: <u32>
> -	Definition: Selects the drive strength for the specified pins, in mA.
> -		    Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
> -
> -Example:
> -
> -	tlmm: pinctrl@3100000 {
> -		compatible = "qcom,sdm660-pinctrl";
> -		reg = <0x3100000 0x200000>,
> -		      <0x3500000 0x200000>,
> -		      <0x3900000 0x200000>;
> -		reg-names = "south", "center", "north";
> -		interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> -		gpio-controller;
> -		gpio-ranges = <&tlmm 0 0 114>;
> -		#gpio-cells = <2>;
> -		interrupt-controller;
> -		#interrupt-cells = <2>;
> -	};
> -- 
> 2.34.1
>
[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux