This converts the Semtech SX150Xq bindings to dt-schemas, add necessary bindings documentation to cover all differences between HW variants and current bindings usage. Signed-off-by: Neil Armstrong <neil.armstrong@xxxxxxxxxx> Reviewed-by: Rob Herring <robh@xxxxxxxxxx> --- To: Rob Herring <robh+dt@xxxxxxxxxx> To: Krzysztof Kozlowski <krzysztof.kozlowski+dt@xxxxxxxxxx> Cc: linux-gpio@xxxxxxxxxxxxxxx Cc: devicetree@xxxxxxxxxxxxxxx Cc: linux-kernel@xxxxxxxxxxxxxxx --- Changes in v2: - fixed rob comments - added rob's Reviewed-by - Link to v1: https://lore.kernel.org/r/20221005-mdm9615-sx1509q-yaml-v1-0-0c26649b637c@xxxxxxxxxx --- .../devicetree/bindings/pinctrl/pinctrl-sx150x.txt | 72 ------- .../bindings/pinctrl/semtech,sx1501q.yaml | 208 +++++++++++++++++++++ 2 files changed, 208 insertions(+), 72 deletions(-) diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt deleted file mode 100644 index 4023bad2fe39..000000000000 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt +++ /dev/null @@ -1,72 +0,0 @@ -SEMTECH SX150x GPIO expander bindings - -Please refer to pinctrl-bindings.txt, ../gpio/gpio.txt, and -../interrupt-controller/interrupts.txt for generic information regarding -pin controller, GPIO, and interrupt bindings. - -Required properties: -- compatible: should be one of : - "semtech,sx1501q", - "semtech,sx1502q", - "semtech,sx1503q", - "semtech,sx1504q", - "semtech,sx1505q", - "semtech,sx1506q", - "semtech,sx1507q", - "semtech,sx1508q", - "semtech,sx1509q". - -- reg: The I2C slave address for this device. - -- #gpio-cells: Should be 2. The first cell is the GPIO number and the - second cell is used to specify optional parameters: - bit 0: polarity (0: normal, 1: inverted) - -- gpio-controller: Marks the device as a GPIO controller. - -Optional properties : -- interrupts: Interrupt specifier for the controllers interrupt. - -- interrupt-controller: Marks the device as a interrupt controller. - -- semtech,probe-reset: Will trigger a reset of the GPIO expander on probe, - only for sx1507q, sx1508q and sx1509q - -The GPIO expander can optionally be used as an interrupt controller, in -which case it uses the default two cell specifier. - -Required properties for pin configuration sub-nodes: - - pins: List of pins to which the configuration applies. - -Optional properties for pin configuration sub-nodes: ----------------------------------------------------- - - bias-disable: disable any pin bias, except the OSCIO pin - - bias-pull-up: pull up the pin, except the OSCIO pin - - bias-pull-down: pull down the pin, except the OSCIO pin - - bias-pull-pin-default: use pin-default pull state, except the OSCIO pin - - drive-push-pull: drive actively high and low - - drive-open-drain: drive with open drain only for sx1507q, sx1508q and sx1509q and except the OSCIO pin - - output-low: set the pin to output mode with low level - - output-high: set the pin to output mode with high level - -Example: - - i2c0gpio-expander@20{ - #gpio-cells = <2>; - #interrupt-cells = <2>; - compatible = "semtech,sx1506q"; - reg = <0x20>; - interrupt-parent = <&gpio_1>; - interrupts = <16 0>; - - gpio-controller; - interrupt-controller; - - pinctrl-names = "default"; - pinctrl-0 = <&gpio1_cfg_pins>; - - gpio1_cfg_pins: gpio1-cfg { - pins = "gpio1"; - bias-pull-up; - }; - }; diff --git a/Documentation/devicetree/bindings/pinctrl/semtech,sx1501q.yaml b/Documentation/devicetree/bindings/pinctrl/semtech,sx1501q.yaml new file mode 100644 index 000000000000..df429a396ba3 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/semtech,sx1501q.yaml @@ -0,0 +1,208 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright 2022 Linaro Ltd. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/semtech,sx1501q.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Semtech SX150x GPIO expander + +maintainers: + - Neil Armstrong <neil.armstrong@xxxxxxxxxx> + +properties: + compatible: + enum: + - semtech,sx1501q + - semtech,sx1502q + - semtech,sx1503q + - semtech,sx1504q + - semtech,sx1505q + - semtech,sx1506q + - semtech,sx1507q + - semtech,sx1508q + - semtech,sx1509q + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + '#interrupt-cells': + const: 2 + + interrupt-controller: true + + '#gpio-cells': + const: 2 + + gpio-controller: true + + semtech,probe-reset: + description: Will trigger a reset of the GPIO expander on probe + type: boolean + +patternProperties: + '-cfg$': + type: object + properties: + pins: true + + bias-disable: true + bias-pull-up: true + bias-pull-down: true + bias-pull-pin-default: true + drive-push-pull: true + output-low: true + output-high: true + drive-open-drain: true + + required: + - pins + + allOf: + - $ref: "pincfg-node.yaml#" + - $ref: "pinmux-node.yaml#" + - if: + properties: + pins: + contains: + const: oscio + then: + properties: + bias-disable: false + bias-pull-up: false + bias-pull-down: false + bias-pull-pin-default: false + drive-open-drain: false + + additionalProperties: false + +required: + - compatible + - reg + - '#gpio-cells' + - gpio-controller + +allOf: + - $ref: "pinctrl.yaml#" + - if: + not: + properties: + compatible: + contains: + enum: + - semtech,sx1507q + - semtech,sx1508q + - semtech,sx1509q + then: + properties: + semtech,probe-reset: false + - if: + properties: + compatible: + contains: + enum: + - semtech,sx1501q + - semtech,sx1504q + then: + patternProperties: + '-cfg$': + properties: + pins: + items: + pattern: '^gpio[0-3]$' + - if: + properties: + compatible: + contains: + enum: + - semtech,sx1502q + - semtech,sx1505q + then: + patternProperties: + '-cfg$': + properties: + pins: + items: + pattern: '^gpio[0-7]$' + - if: + properties: + compatible: + contains: + enum: + - semtech,sx1503q + - semtech,sx1506q + then: + patternProperties: + '-cfg$': + properties: + pins: + items: + pattern: '^gpio[0-15]$' + - if: + properties: + compatible: + contains: + const: semtech,sx1507q + then: + patternProperties: + '-cfg$': + properties: + pins: + items: + pattern: '^(oscio|gpio[0-3])$' + - if: + properties: + compatible: + contains: + const: semtech,sx1508q + then: + patternProperties: + '-cfg$': + properties: + pins: + items: + pattern: '^(oscio|gpio[0-7])$' + - if: + properties: + compatible: + contains: + const: semtech,sx1509q + then: + patternProperties: + '-cfg$': + properties: + pins: + items: + pattern: '^(oscio|gpio[0-15])$' + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c@1000 { + reg = <0x1000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + + pinctrl@20 { + compatible = "semtech,sx1501q"; + reg = <0x20>; + + #gpio-cells = <2>; + #interrupt-cells = <2>; + + interrupts = <16 IRQ_TYPE_EDGE_FALLING>; + + gpio-controller; + interrupt-controller; + + gpio1-cfg { + pins = "gpio1"; + bias-pull-up; + }; + }; + }; --- base-commit: 4fe89d07dcc2804c8b562f6c7896a45643d34b2f change-id: 20221005-mdm9615-sx1509q-yaml-7cfabf896fff Best regards, -- Neil Armstrong <neil.armstrong@xxxxxxxxxx>
[PATCH v2] dt-bindings: pinctrl: convert semtech,sx150xq bindings to dt-schema
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
- Subject: [PATCH v2] dt-bindings: pinctrl: convert semtech,sx150xq bindings to dt-schema
- From: Neil Armstrong <neil.armstrong@xxxxxxxxxx>
- Date: Thu, 13 Oct 2022 08:37:15 +0200
- Prev by Date: Re: [PATCH V6 3/8] libgpiod: Add rust wrapper crate
- Next by Date: Re: [PATCH 7/8] serial: 8250/ingenic: Add support for the JZ4750/JZ4755 SoCs
- Previous by thread: [PATCH AUTOSEL 5.15 18/47] gpiolib: rework quirk handling in of_find_gpio()
- Next by thread: [PATCH v2 0/1] Improved debugging for active GPIO causing wakeup
- Index(es):
 |