[PATCH V2] dt-bindings: gpio: gpio-xilinx: Convert Xilinx axi gpio binding to YAML

[Srinivas Neeli <srinivas.neeli@xxxxxxxxxx>]

Convert Xilinx axi gpio binding documentation to YAML.

Signed-off-by: Srinivas Neeli <srinivas.neeli@xxxxxxxxxx>
---
Changes in V2:
- Updated mainter email with s-o-b.
- Updated few constraints.
- Addressed few other comments.
---
 .../devicetree/bindings/gpio/gpio-xilinx.txt  |  48 ------
 .../bindings/gpio/xlnx,gpio-xilinx.yaml       | 154 ++++++++++++++++++
 2 files changed, 154 insertions(+), 48 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/gpio/gpio-xilinx.txt
 create mode 100644 Documentation/devicetree/bindings/gpio/xlnx,gpio-xilinx.yaml

diff --git a/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt b/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt
deleted file mode 100644
index e506f30e1a95..000000000000
--- a/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt
+++ /dev/null
@@ -1,48 +0,0 @@
-Xilinx plb/axi GPIO controller
-
-Dual channel GPIO controller with configurable number of pins
-(from 1 to 32 per channel). Every pin can be configured as
-input/output/tristate. Both channels share the same global IRQ but
-local interrupts can be enabled on channel basis.
-
-Required properties:
-- compatible : Should be "xlnx,xps-gpio-1.00.a"
-- reg : Address and length of the register set for the device
-- #gpio-cells : Should be two. The first cell is the pin number and the
-  second cell is used to specify optional parameters (currently unused).
-- gpio-controller : Marks the device node as a GPIO controller.
-
-Optional properties:
-- clocks : Input clock specifier. Refer to common clock bindings.
-- interrupts : Interrupt mapping for GPIO IRQ.
-- xlnx,all-inputs : if n-th bit is setup, GPIO-n is input
-- xlnx,dout-default : if n-th bit is 1, GPIO-n default value is 1
-- xlnx,gpio-width : gpio width
-- xlnx,tri-default : if n-th bit is 1, GPIO-n is in tristate mode
-- xlnx,is-dual : if 1, controller also uses the second channel
-- xlnx,all-inputs-2 : as above but for the second channel
-- xlnx,dout-default-2 : as above but the second channel
-- xlnx,gpio2-width : as above but for the second channel
-- xlnx,tri-default-2 : as above but for the second channel
-
-
-Example:
-gpio: gpio@40000000 {
-	#gpio-cells = <2>;
-	compatible = "xlnx,xps-gpio-1.00.a";
-	clocks = <&clkc25>;
-	gpio-controller ;
-	interrupt-parent = <&microblaze_0_intc>;
-	interrupts = < 6 2 >;
-	reg = < 0x40000000 0x10000 >;
-	xlnx,all-inputs = <0x0>;
-	xlnx,all-inputs-2 = <0x0>;
-	xlnx,dout-default = <0x0>;
-	xlnx,dout-default-2 = <0x0>;
-	xlnx,gpio-width = <0x2>;
-	xlnx,gpio2-width = <0x2>;
-	xlnx,interrupt-present = <0x1>;
-	xlnx,is-dual = <0x1>;
-	xlnx,tri-default = <0xffffffff>;
-	xlnx,tri-default-2 = <0xffffffff>;
-} ;
diff --git a/Documentation/devicetree/bindings/gpio/xlnx,gpio-xilinx.yaml b/Documentation/devicetree/bindings/gpio/xlnx,gpio-xilinx.yaml
new file mode 100644
index 000000000000..f333ee2288e7
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/xlnx,gpio-xilinx.yaml
@@ -0,0 +1,154 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/gpio/xlnx,gpio-xilinx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx AXI GPIO controller
+
+maintainers:
+  - Neeli Srinivas <srinivas.neeli@xxxxxxxxxx>
+
+description:
+  The AXI GPIO design provides a general purpose input/output interface
+  to an AXI4-Lite interface. The AXI GPIO can be configured as either
+  a single or a dual-channel device. The width of each channel is
+  independently configurable. The channels can be configured to
+  generate an interrupt when a transition on any of their inputs occurs.
+
+properties:
+  compatible:
+    enum:
+      - xlnx,xps-gpio-1.00.a
+
+  reg:
+    maxItems: 1
+
+  "#gpio-cells":
+    const: 2
+
+  interrupts:
+    maxItems: 1
+
+  gpio-controller: true
+
+  gpio-line-names:
+    description: strings describing the names of each gpio line
+    minItems: 1
+    maxItems: 64
+
+  interrupt-controller: true
+
+  "#interrupt-cells":
+    const: 2
+
+  clocks:
+    maxItems: 1
+
+  interrupt-names: true
+
+  xlnx,all-inputs:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: This option sets this GPIO channel1 bits in input mode.
+
+  xlnx,all-inputs-2:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: This option sets this GPIO channel2 bits in input mode.
+
+  xlnx,all-outputs:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: This option sets this GPIO channel1 bits in output mode.
+
+  xlnx,all-outputs-2:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: This option sets this GPIO channel2 bits in output mode.
+
+  xlnx,dout-default:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: Sets the default value of all the enabled bits of
+                 channel1.
+    default: 0
+
+  xlnx,dout-default-2:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: Sets the default value of all the enabled bits of
+                 channel2.
+    default: 0
+
+  xlnx,gpio-width:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: The value defines the bit width of the GPIO channel1.
+    minimum: 1
+    maximum: 32
+    default: 32
+
+  xlnx,gpio2-width:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: The value defines the bit width of the GPIO channel2.
+    minimum: 1
+    maximum: 32
+    default: 32
+
+  xlnx,interrupt-present:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: This parameter enables interrupt control logic
+                 and interrupt registers in GPIO module.
+    minimum: 0
+    maximum: 1
+    default: 0
+
+  xlnx,is-dual:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: This parameter enables a second GPIO channel (GPIO2).
+    minimum: 0
+    maximum: 1
+    default: 0
+
+  xlnx,tri-default:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: This value configures the input or output mode
+                 of each bit of GPIO channel1.
+
+  xlnx,tri-default-2:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: This value configures the input or output mode
+                 of each bit of GPIO channel2.
+
+required:
+  - reg
+  - compatible
+  - gpio-controller
+  - "#gpio-cells"
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+        gpio@e000a000 {
+            compatible = "xlnx,xps-gpio-1.00.a";
+            reg = <0xa0020000 0x10000>;
+            #gpio-cells = <2>;
+            #interrupt-cells = <0x2>;
+            clocks = <&zynqmp_clk 71>;
+            gpio-controller;
+            interrupt-controller;
+            interrupt-names = "ip2intc_irpt";
+            interrupt-parent = <&gic>;
+            interrupts = <0 89 4>;
+            xlnx,all-inputs = <0x0>;
+            xlnx,all-inputs-2 = <0x0>;
+            xlnx,all-outputs = <0x0>;
+            xlnx,all-outputs-2 = <0x0>;
+            xlnx,dout-default = <0x0>;
+            xlnx,dout-default-2 = <0x0>;
+            xlnx,gpio-width = <0x20>;
+            xlnx,gpio2-width = <0x20>;
+            xlnx,interrupt-present = <0x1>;
+            xlnx,is-dual = <0x1>;
+            xlnx,tri-default = <0xFFFFFFFF>;
+            xlnx,tri-default-2 = <0xFFFFFFFF>;
+        };
+
+...
-- 
2.17.1