Re: [PATCH 1/3] dt-bindings: mediatek: add pinctrl definition for mt8188

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 

On 18/07/2022 13:38, Hui Liu wrote:
> From: "Hui.Liu" <hui.liu@xxxxxxxxxxxx>
> 
> This commit adds mt8188 compatible node in binding document.
> 
> Signed-off-by: Hui.Liu <hui.liu@xxxxxxxxxxxx>
> ---
>  .../bindings/pinctrl/pinctrl-mt8188.yaml      | 306 ++++++++++++++++++
>  1 file changed, 306 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/pinctrl-mt8188.yaml
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8188.yaml b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8188.yaml
> new file mode 100644
> index 000000000000..43cc2424107f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8188.yaml

vendor,soc-ip
so:
mediatek,mt8188-pinctrl.yaml

> @@ -0,0 +1,306 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/pinctrl-mt8188.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: MediaTek MT8188 Pin Controller
> +
> +maintainers:
> +  - Sean Wang <sean.wang@xxxxxxxxxxxx>
> +
> +description: |
> +  The MediaTek's Pin controller is used to control SoC pins.

Too generic description. Just drop it or make it useful.

> +
> +properties:
> +  compatible:
> +    const: mediatek,mt8188-pinctrl
> +
> +  gpio-controller: true
> +
> +  '#gpio-cells':
> +    description: |
> +      Number of cells in GPIO specifier. Since the generic GPIO binding is used,
> +      the amount of cells must be specified as 2. See the below
> +      mentioned gpio binding representation for description of particular cells.

Comment does not make sense.

> +    const: 2
> +
> +  gpio-ranges:
> +    description: gpio valid number range.

Redundant description, skip it.

> +    maxItems: 1
> +
> +  reg:
> +    description: |
> +      Physical address base for gpio base registers. There are 8 GPIO
> +      physical address base in mt8188.

Redundant description, skip it. You should list the instead and describe
each of it.

> +    maxItems: 8
> +
> +  reg-names:
> +    description: |
> +      Gpio base register names.

Redundant description, skip it.

> +    maxItems: 8

You need to list the items instead.

> +
> +  interrupt-controller: true
> +
> +  '#interrupt-cells':
> +    const: 2
> +
> +  interrupts:
> +    description: The interrupt outputs to sysirq.
> +    maxItems: 1
> +
> +  mediatek,rsel_resistance_in_si_unit:

No underscores in property names.

> +    type: boolean
> +    description: |
> +      Identifying i2c pins pull up/down type which is RSEL. It can support
> +      RSEL define or si unit value(ohm) to set different resistance.

I cannot understand this description.

> +
> +# PIN CONFIGURATION NODES
> +patternProperties:
> +  '-pins$':
> +    type: object
> +    additionalProperties: false

Blank line. Missing ref to proper generic pinctrl schema.

> +    patternProperties:
> +      '^pins':
> +        type: object
> +        additionalProperties: false

Blank line. Missing ref to proper generic pinctrl schema.


> +        description: |
> +          A pinctrl node should contain at least one subnodes representing the
> +          pinctrl groups available on the machine. Each subnode will list the
> +          pins it needs, and how they should be configured, with regard to muxer
> +          configuration, pullups, drive strength, input enable/disable and
> +          input schmitt.
> +          An example of using macro:
> +          pincontroller {
> +            /* GPIO0 set as multifunction GPIO0 */
> +            gpio-pins {
> +              pins {
> +                pinmux = <PINMUX_GPIO0__FUNC_B_GPIO0>;
> +              }
> +            };
> +            /* GPIO56 set as multifunction SDA0 */
> +            i2c0-pins {
> +              pins {
> +                pinmux = <PINMUX_GPIO56__FUNC_B1_SDA0>;
> +              }
> +            };

Drop the code from here. Put it in example.

> +          };
> +        $ref: "pinmux-node.yaml"

Oh, why it's here. This should be just after type.

> +
> +        properties:
> +          pinmux:
> +            description: |
> +              Integer array, represents gpio pin number and mux setting.
> +              Supported pin number and mux varies for different SoCs, and are
> +              defined as macros in dt-bindings/pinctrl/<soc>-pinfunc.h
> +              directly.
> +
> +          drive-strength:
> +            enum: [2, 4, 6, 8, 10, 12, 14, 16]
> +
> +          mediatek,drive-strength-adv:
> +            description: |
> +              Describe the specific driving setup property.
> +              For I2C pins, the existing generic driving setup can only support
> +              2/4/6/8/10/12/14/16mA driving. But in specific driving setup, they
> +              can support 0.125/0.25/0.5/1mA adjustment. If we enable specific
> +              driving setup, the existing generic setup will be disabled.
> +              The specific driving setup is controlled by E1E0EN.
> +              When E1=0/E0=0, the strength is 0.125mA.
> +              When E1=0/E0=1, the strength is 0.25mA.
> +              When E1=1/E0=0, the strength is 0.5mA.
> +              When E1=1/E0=1, the strength is 1mA.
> +              EN is used to enable or disable the specific driving setup.
> +              Valid arguments are described as below:
> +              0: (E1, E0, EN) = (0, 0, 0)
> +              1: (E1, E0, EN) = (0, 0, 1)
> +              2: (E1, E0, EN) = (0, 1, 0)
> +              3: (E1, E0, EN) = (0, 1, 1)
> +              4: (E1, E0, EN) = (1, 0, 0)
> +              5: (E1, E0, EN) = (1, 0, 1)
> +              6: (E1, E0, EN) = (1, 1, 0)
> +              7: (E1, E0, EN) = (1, 1, 1)
> +              So the valid arguments are from 0 to 7.
> +            $ref: /schemas/types.yaml#/definitions/uint32
> +            enum: [0, 1, 2, 3, 4, 5, 6, 7]

No. Use logical units instead, so this should be either mA, no register
hard-coding in the bindings.

> +
> +          bias-pull-down:
> +            oneOf:
> +              - type: boolean
> +              - enum: [100, 101, 102, 103]
> +                description: mt8188 pull down PUPD/R0/R1 type define value.
> +              - enum: [200, 201, 202, 203, 204, 205, 206, 207]
> +                description: mt8188 pull down RSEL type define value.
> +              - enum: [75000, 5000]
> +                description: mt8188 pull down RSEL type si unit value(ohm).
> +            description: |
> +              For pull down type is normal, it don't need add RSEL & R1R0 define
> +              and resistance value.
> +              For pull down type is PUPD/R0/R1 type, it can add R1R0 define to
> +              set different resistance. It can support "MTK_PUPD_SET_R1R0_00" &
> +              "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" &
> +              "MTK_PUPD_SET_R1R0_11" define in mt8188.
> +              For pull down type is RSEL, it can add RSEL define & resistance
> +              value(ohm) to set different resistance by identifying property
> +              "mediatek,rsel_resistance_in_si_unit".
> +              It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001"
> +              & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011"
> +              & "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101"
> +              & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111"
> +              define in mt8188. It can also support resistance value(ohm)
> +              "75000" & "5000" in mt8188.
> +
> +              An example of using RSEL define:
> +              pincontroller {
> +                i2c0_pin {
> +                  pins {
> +                    pinmux = <PINMUX_GPIO56__FUNC_B1_SDA0>;
> +                    bias-pull-updown = <MTK_PULL_SET_RSEL_001>;
> +                  }
> +                };
> +              };
> +              An example of using si unit resistance value(ohm):
> +              &pio {
> +                mediatek,rsel_resistance_in_si_unit;
> +              }
> +              pincontroller {
> +                i2c0_pin {
> +                  pins {
> +                    pinmux = <PINMUX_GPIO56__FUNC_B1_SDA0>;
> +                    bias-pull-down = <75000>;
> +                  }
> +                };
> +              };

To the example.

> +
> +          bias-pull-up:
> +            oneOf:
> +              - type: boolean
> +              - enum: [100, 101, 102, 103]
> +                description: mt8188 pull up PUPD/R0/R1 type define value.
> +              - enum: [200, 201, 202, 203, 204, 205, 206, 207]
> +                description: mt8188 pull up RSEL type define value.
> +              - enum: [1000, 1500, 2000, 3000, 4000, 5000, 10000, 75000]
> +                description: mt8188 pull up RSEL type si unit value(ohm).
> +            description: |
> +              For pull up type is normal, it don't need add RSEL & R1R0 define
> +              and resistance value.
> +              For pull up type is PUPD/R0/R1 type, it can add R1R0 define to
> +              set different resistance. It can support "MTK_PUPD_SET_R1R0_00" &
> +              "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" &
> +              "MTK_PUPD_SET_R1R0_11" define in mt8188.
> +              For pull up type is RSEL, it can add RSEL define & resistance
> +              value(ohm) to set different resistance by identifying property
> +              "mediatek,rsel_resistance_in_si_unit".
> +              It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001"
> +              & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011"
> +              & "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101"
> +              & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111"
> +              define in mt8188. It can also support resistance value(ohm)
> +              "1000" & "1500" & "2000" & "3000" & "4000" & "5000" & "10000" &
> +              "75000" in mt8188.
> +              An example of using RSEL define:
> +              pincontroller {
> +                i2c0-pins {
> +                  pins {
> +                    pinmux = <PINMUX_GPIO56__FUNC_B1_SDA0>;
> +                    bias-pull-up = <MTK_PULL_SET_RSEL_001>;
> +                  }
> +                };
> +              };
> +              An example of using si unit resistance value(ohm):
> +              &pio {
> +                mediatek,rsel_resistance_in_si_unit;
> +              }
> +              pincontroller {
> +                i2c0-pins {
> +                  pins {
> +                    pinmux = <PINMUX_GPIO56__FUNC_B1_SDA0>;
> +                    bias-pull-up = <1000>;
> +                  }
> +                };
> +              };

The same.

> +
> +          bias-disable: true
> +
> +          output-high: true
> +
> +          output-low: true
> +
> +          input-enable: true
> +
> +          input-disable: true
> +
> +          input-schmitt-enable: true
> +
> +          input-schmitt-disable: true
> +
> +        required:
> +          - pinmux
> +
> +allOf:
> +  - $ref: "pinctrl.yaml#"

No need for quotes, especially that you use different here " than in
other places '.



Best regards,
Krzysztof
[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux