Re: [PATCH 11/11] arm64: dts: Add Pensando Elba SoC support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 07/04/2022 01:36, Brad Larson wrote:
> Add Pensando common and Elba SoC specific device nodes
> 
> Signed-off-by: Brad Larson <brad@xxxxxxxxxxx>
> ---
> Change from V3:
> - Changed to dual copyright (GPL-2.0+ OR MIT)
> - Minor changes from review input

Thank you for your patch. There is something to discuss/improve.

(...)

> +&i2c0 {
> +	clock-frequency = <100000>;
> +	status = "okay";
> +	rtc@51 {
> +		compatible = "nxp,pcf85263";
> +		reg = <0x51>;
> +	};
> +};
> +
> +&spi0 {
> +	num-cs = <4>;
> +	cs-gpios = <0>, <0>, <&porta 1 GPIO_ACTIVE_LOW>,
> +		   <&porta 7 GPIO_ACTIVE_LOW>;
> +	status = "okay";
> +	spi0_cs0@0 {

Generic node name needed matching the class of a devicxe.

> +		compatible = "semtech,sx1301";	/* Enable spidev */

This comment is a bit odd... did you just use random compatible from
spidev instead of defining proper compatible?


> +		#address-cells = <1>;
> +		#size-cells = <1>;

Why address/size cells?

> +		spi-max-frequency = <12000000>;
> +		reg = <0>;

Please put reg just after compatible. It's the most common pattern.

> +	};
> +
> +	spi0_cs1@1 {
> +		compatible = "semtech,sx1301";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		spi-max-frequency = <12000000>;
> +		reg = <1>;
> +	};
> +

(...)

> +
> +		emmc: mmc@30440000 {
> +			compatible = "pensando,elba-sd4hc", "cdns,sd4hc";
> +			clocks = <&emmc_clk>;
> +			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
> +			reg = <0x0 0x30440000 0x0 0x10000>,
> +			      <0x0 0x30480044 0x0 0x4>;	/* byte-lane ctrl */
> +			cdns,phy-input-delay-sd-highspeed = <0x4>;
> +			cdns,phy-input-delay-legacy = <0x4>;
> +			cdns,phy-input-delay-sd-uhs-sdr50 = <0x6>;
> +			cdns,phy-input-delay-sd-uhs-ddr50 = <0x16>;
> +			mmc-ddr-1_8v;
> +			status = "disabled";
> +		};
> +
> +		mssoc: mssoc@307c0000 {

Generic node name.

> +			compatible = "syscon", "simple-mfd";

This does not look correct. Syscon is okay, but why do you need
simple-mfd (there are no children here)?

> +			reg = <0x0 0x307c0000 0x0 0x3000>;
> +		};
> +	};
> +};


Best regards,
Krzysztof



[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux