Re: [PATCH] spmi: pmic-arb: Add support for PMIC v7

[David Collins <quic_collinsd@xxxxxxxxxxx>]

On 12/2/21 3:06 PM, Stephen Boyd wrote:
> Quoting Vinod Koul (2021-11-30 23:27:18)
>> @@ -1169,8 +1270,12 @@ static int spmi_pmic_arb_probe(struct platform_device *pdev)
>>         pmic_arb = spmi_controller_get_drvdata(ctrl);
>>         pmic_arb->spmic = ctrl;
>>  
>> +       /*
>> +        * Don't use devm_ioremap_resource() as the resources are shared in
>> +        * PMIC v7 onwards, so causing failure when mapping
>> +        */
>>         res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "core");
>> -       core = devm_ioremap_resource(&ctrl->dev, res);
>> +       core = devm_ioremap(&ctrl->dev, res->start, resource_size(res));
> 
> What does this mean? We have two nodes in DT that have the same reg
> properties? How does that work?

PMIC Arbiter v7 has two SPMI bus master interfaces.  These are used to
communicate with two sets of PMICs.  The SPMI interfaces operate
independently; however, they share some register address ranges (e.g.
one common one is used for APID->PPID mapping).  The most
straightforward way to handle this is to treat them as two independent
top-level DT devices.

In this case the "cnfg" address is used in the DT node name as that is
unique between the two instances.

Here are the DT nodes used downstream on a target with PMIC Arbiter v7:

spmi0_bus: qcom,spmi@c42d000 {
	compatible = "qcom,spmi-pmic-arb";
	reg = <0xc42d000 0x4000>,
	      <0xc400000 0x3000>,
	      <0xc500000 0x400000>,
	      <0xc440000 0x80000>,
	      <0xc4c0000 0x10000>;
	reg-names = "cnfg", "core", "chnls", "obsrvr", "intr";
	interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
	interrupt-names = "periph_irq";
	interrupt-controller;
	#interrupt-cells = <4>;
	#address-cells = <2>;
	#size-cells = <0>;
	cell-index = <0>;
	qcom,channel = <0>;
	qcom,ee = <0>;
	qcom,bus-id = <0>;
};

spmi1_bus: qcom,spmi@c432000 {
	compatible = "qcom,spmi-pmic-arb";
	reg = <0xc432000 0x4000>,
	      <0xc400000 0x3000>,
	      <0xc500000 0x400000>,
	      <0xc440000 0x80000>,
	      <0xc4d0000 0x10000>;
	reg-names = "cnfg", "core", "chnls", "obsrvr", "intr";
	interrupts-extended = <&pdc 3 IRQ_TYPE_LEVEL_HIGH>;
	interrupt-names = "periph_irq";
	interrupt-controller;
	#interrupt-cells = <4>;
	#address-cells = <2>;
	#size-cells = <0>;
	cell-index = <0>;
	qcom,channel = <0>;
	qcom,ee = <0>;
	qcom,bus-id = <1>;
};

Note the inclusion of a new DT property: "qcom,bus-id".  This was
defined in a DT binding patch that isn't present in Vinod's submission.
Here is its definition:

- qcom,bus-id : Specifies which SPMI bus instance to use.  This property
		is only applicable for PMIC arbiter version 7 and
		beyond.
		Support values: 0 = primary bus, 1 = secondary bus
		Assumed to be 0 if unspecified.

Take care,
David